how do you adjust a poulan pro chainsaw

by Cecil Osinski Published 2 years ago Updated 1 year ago

How do you adjust a Poulan Pro chainsaw?

Before you start the saw, locate a small flat-bladed screwdriver.
Begin by checking the saw's air filter.
Check the fuel level.
Start the engine and warm it up.
Begin by setting the idle speed.
Set the low speed fuel adjustment.
Go back to step (4) and reset the idle speed.

Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly. As soon as the chain starts to move, turn the screw counterclockwise until the engine idles without dying and the chain stops moving for the correct idle speed.

Full Answer

How to replace chain adjuster screw on Poulan chainsaw?

Place the saw on a flat bench and ensure there are no obstructions around the chain, which will spin during this procedure.
Unscrew and remove the three screws holding the engine cover and remove the cover.
Locate the idle adjustment screw.
Start the saw and let it idle for two or three minutes to warm up.
Tip.

What tool is needed to adjust CARB on Poulan chainsaw?

[Learn to Tune Right]

Reasons to Adjust Your Carburetor. If you don’t monitor the air and fuel needs of your chainsaw, the excessive smoke build-up can cause longtime damage to the saw’s engine.
The Three Carburetor Adjustment Slots. ...
Tools You’ll Need to Buy. ...

How to tune a Poulan chainsaw?

Tuning a Poulan Pro Chain Saw

Put on your gloves and take your Poulan Pro saw to a clear area with level ground. Make sure no bystanders are within reach of the saw.
Unscrew the three screws securing the black cylinder cover on top of the saw, and remove the cylinder cover and air filter cover.
Put the saw on the ground and set the start switch to the "On" position. ...

More items...

Are Poulan chainsaws better than McCulloch chainsaws?

Top positive review I use several saws from, Stihl, Homelite, Poulan and McCulloch. By far this McCulloch saw for the money is great. It is powerful and does not bog down easily. I would recommend this saw to anyone who is considering purchasing a fine chainsaw.

How do you adjust the high and low on a Poulan chainsaw?

6:297:40HOW TO ADJUST POULAN CHAINSAW CARBURETORYouTubeStart of suggested clipEnd of suggested clipI just checked it is about a turn and a half for the low screw. And one. And a half about one to oneMoreI just checked it is about a turn and a half for the low screw. And one. And a half about one to one and a half for the high. Try one and a half on both and then go from there.

How do you adjust the fuel and air mixture on a Poulan Pro chainsaw?

Replace the filter, start the saw and turn the "T" screw counterclockwise to increase the fuel mixture and the idle speed; turning the screw counterclockwise decreases both. You've achieved the proper fuel mixture when the engine idles smoothly but the chain doesn't spin.

How do you adjust a Poulan Pro?

2:237:01Carb Adjust on Poulon Pro 42cc Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow here is my pooling Pro okay so 42 CC Poulan Pro with a there's a chain tensioner which ain't noMoreNow here is my pooling Pro okay so 42 CC Poulan Pro with a there's a chain tensioner which ain't no big deal I mean but it's a nice little entry-level chainsaw for the size of them these chainsaws get

What is the L and H on a Poulan chainsaw?

The low end is when the trigger is first pulled. The H screw controls the air-fuel mixture of the high end of the chainsaw's throttle response. The high end is when the chainsaw's engine speed is topped out. Adjusting the L and H screws controls the chainsaws' throttle response, (low end), and high-end engine RPMs.

Why does my Poulan chainsaw dies when I give it gas?

A clogged fuel filter is often caused by leaving old fuel in the chainsaw. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the fuel filter and cause the engine to stall.

Why does my chainsaw bog down when I give it gas?

There are several factors may make your saw not work properly. First, it could be that the carburetor, spark arrestor or the air filter are dirty. Or, the carburetor adjustment might have simply slipped. This guide will explore some of the reasons why you chainsaw bogs down as well as the different ways to fix it.

What is the T adjustment on a Poulan chainsaw?

To adjust the carburetor idle speed, locate the idle speed screw labeled with a "T" just above the primer bulb. Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything.

How do you adjust the T screws on a chainsaw?

1:442:50Chainsaw Fuel Screws Adjustment to Correct Bog Down, Won ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo it's worth adjusting the third screw labeled t-screw or idling screw outwards anti-clockwiseMoreSo it's worth adjusting the third screw labeled t-screw or idling screw outwards anti-clockwise steadily until the engine revs lower and the chain.

What does LH and T mean on a chainsaw?

They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet). Your saw may be labeled differently (in the photos in the Gallery below, the idler jet is labeled “S”), but you'll have three screws that correspond to these descriptions.

What do H and L screws do on a carburetor?

This adjustment controls the fuel flow to the low speed or idle circuit. If the carburetor is too far out of adjustment to run, or has been disassembled, start with turning the L and H all the way in and then open 2 turns on each needle.

How do you adjust a carburetor?

0:412:42How To Adjust A Carburetor On Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd all you need is a screwdriver on the front turn it to the left makes it go slower turning to theMoreAnd all you need is a screwdriver on the front turn it to the left makes it go slower turning to the right makes it go faster. So with the engine running turn the screw. So it idles decently.

How do you adjust a Walbro carburetor?

0:332:02Hidden Adjustment Screw On Walbro Carburetors - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd after you've adjusted the small screw inside and it runs good just put the little plastic capMoreAnd after you've adjusted the small screw inside and it runs good just put the little plastic cap back on all you have to do is just simply put it on like this and push down.

Carburetor Function

In the same way as a carburetor on an automobile or other small engines works, a Poulan chain saw carburetor works in the same way. This can be accomplished by increasing the proportion of fuel and oil in the air mixture, or it can be accomplished by decreasing the proportion of fuel and oil to air in the engine mixture.

Problems with Idle Speed

When a carburetor fails to start after being started, is difficult to start, or fails to start when under load, adjustments must be made. In these instances, it is necessary to increase the fuel and oil ratio in relation to the air.

Safety must be prioritized

Before you can adjust the carburetor on your Poulan chainsaw, make sure it’s on a flat, level surface with the chain hanging over the edge, or clear the area of anything that might get in the way of the chain.

Knowledge Builders