Adjusting your shift cables.
- put the control into full forward wide open throttle position.
- Raise outdrive approximately 1/2 the distance under normal trim function (NOT TRAILER). Trim ram (stainless shaft exposure) should be approximately 1 ...
- have second person rotate prop counterclockwise until solid (no clicking or intermittent engagement) engagement.
- disconnect short shift cable and control cable from shift bracket.
- with plastic shift cable end PUSHED all the way in, confirm full forward engagement at the prop.
- Measure 6 inches ( NO MORE THAN 6) from the center of the eye in the plastic end to the center of the brass trunion. 1/16 of an inch LESS is ...
Full Answer
How to adjust transmission shift cable?
If you are only making an adjustment to the shift cable, follow these steps:
- Examine the shift cable closely for any damage.
- If it is damaged you must go for a full replacement.
- Do this inspection when the golf cart’s engine is off.
- Allow the engine to cool before you do this exercise.
- The adjustment has to be done at both ends.
- One is the transaxle end and the other end is where you use the handle to shift R and F.
How do I adjust shifter cable?
Steps for Shifter Cable Replacement
- Shift the chain onto the smallest front and rear cogs.
- Unwrap your bar tape in order to access the shifters.
- Clip off the end cap and remove the cable from the old housing.
- Fully remove the old cable from the shifter.
- Use the old housing as a guide measure, and cut the new lengths of cable housing.
How to adjust your MerCruiser shift cable?
Adjust the cable so it fits snugly between the studs, which are pre-mounted and hold the shift cable in position. If there is slack in the cable, then you need to make another adjustment. What causes shift cable to stretch on MerCruiser? Mercury Marine’s MerCruiser stern drive system consists of the engine, outdrive and operator controls.
How to remove shift cable?
- Push the clip towards the hole while lifting on the curved end with the pliers.
- Be sure retainer clip fully engages the pin.
- Lock the retainer by moving the angled section behind the straight section.
Can you adjust a shift cable?
1:443:29HOW TO ADJUST TRANSMISSION SHIFT CABLE LINKAGE ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're just going to get it okay like that to where it needs to be guys you need to do some testingMoreYou're just going to get it okay like that to where it needs to be guys you need to do some testing to make sure that. Everything performs correctly what I recommend.
How do you adjust a shifter cable on a manual transmission?
1:086:21VW MK4, MK5, and MK6 5 speed shifter adjustment for ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to pull the cable out or I pull all the slack out and then we're gonna turn the ringMoreSo we're going to pull the cable out or I pull all the slack out and then we're gonna turn the ring counterclockwise. And let it snap.
How do I know if my lower shift cable is adjusting?
1:396:16Mercruiser Alpha Shift cable adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce that's adjusted to 6 inches that is it that is the only adjustment on the lower shift cable andMoreOnce that's adjusted to 6 inches that is it that is the only adjustment on the lower shift cable and that stays.
How do I adjust my shifters?
2:307:40How to adjust a motorcycle shift lever (simple & basic) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat happens is you just rotate this and it'll either pull it in equally. Or pull it apart equallyMoreWhat happens is you just rotate this and it'll either pull it in equally. Or pull it apart equally all right and that'll make an adjustment.
How tight should gear cable?
0:282:11How to Adjust Rear Derailleur Cable Tension - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you've done that. And you'll get more than five millimeters of play here as a good indicationMoreOnce you've done that. And you'll get more than five millimeters of play here as a good indication that your cable is loose.
How do you fix a loose shift linkage?
0:534:09How to Fix a Loose Column Shifter - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see how they're both loose. And it allows a lot of slop in here a lot of play and that playMoreYou can see how they're both loose. And it allows a lot of slop in here a lot of play and that play gets transferred into this which then goes to your transmission and shifts the gears.
How do you adjust a lower shift cable?
0:286:12How To: Install a Sterndrive Assembly - Shift Cable Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we're going to remove the lower shift cable and we will just take off the nut on the front side.MoreNow we're going to remove the lower shift cable and we will just take off the nut on the front side. And the cotter pin on the back. Side. I'm going to go ahead and remove the cable.
How do you adjust a throttle and shift cable?
0:373:22Outboard control cable adjustment for shifting gears - forward / reverseYouTubeStart of suggested clipEnd of suggested clipWhen you push the cable the throttle goes slowly in and out so for example if you adjust the cable aMoreWhen you push the cable the throttle goes slowly in and out so for example if you adjust the cable a little bit. It will make a difference in the way it works.
What are the likely problems if the selector linkage is not correctly adjusted?
If the linkage is not correctly aligned, it will cause various problems, including an inability to engage drive or to start the engine. Keep in mind that the exact adjustment method depends on the transmission type and the design of the linkage.
How do I know if my shift linkage is bad?
Bad Shift Linkage Bushing SymptomsGrinding noise. If you notice a grinding sound from the transmission, it may be due to clashing gears. ... Odd sounds like thumping, bumping, squealing, and whirring. The odd noises coming from the shift linkage may be due to insufficient oil. ... Transmission oil leaks.
How do I know if my shifter cable is broken?
If the shift cable breaks, your shifter handle won't return to its neutral position on its own. If the horizontal cable breaks, you won't be able to shift. If the vertical cable breaks, you will only be able to shift to third or fourth gear.
How does a shifter cable work?
0:072:05Common Mistakes Installing Transmission- Shifter CablesYouTubeStart of suggested clipEnd of suggested clipAnd these cables nowadays these ends are made of plastic. And then they have a rubber bushing thatMoreAnd these cables nowadays these ends are made of plastic. And then they have a rubber bushing that goes inside that that cable that pushes onto a plunger that holds that cable on there.
How to keep shifter cable from moving?
Then tighten the locking screws to keep the cable sleeve from moving in the future. Vehicle Repairs.
What to do if your shift is not hitting the correct gear?
If your vehicle is not hitting the correct gear when you shift, you might have to adjust your shift cables. If you check the cable on both ends of the line on the engine and at the stick shift and the cable is not broken, you can fix them with an adjustment.
How to put a shifter in neutral?
Put the shifter into a neutral position. Once it is in neutral gear you will then go and check the position of your shifting arm on the transmission. Double check and make sure the stick is in a neutral position so that it is easier to line up the engine side of your cable.
