Ensure that your material is properly secured on the K4 before you start drilling into it. To adjust, loosen the lock nut, and turn the rubber foot to the desired length. When you bring the clamp handle down, you should feel it “lock” into position.
How to set up the KREG pocket hole jig?
The Simple Rule for Joining Different Thicknesses with Pocket Holes
- Using pocket holes to join materials of different thicknesses can be confusing. ...
- The Simple Rule for Joining Different Thicknesses with Pocket Holes. ...
- More Tips for Pocket Hole Joints. ...
- FREE Pocket Hole Mistakes Guide. ...
- Pocket Hole Questions. ...
- Final Thoughts. ...
How to highlight your KREG jig?
- A drill guide, on the jig itself
- A clamp that helps hold the wood in place (also attached to the jig)
- A material thickness gauge
- A drill bit to create the pocket hole
- A depth collar to set the depth for the pocket hole (more on this in a minute)
- A square driver bit to drive the screws into the pocket hole
How to use a KREG jig?
Instructions
- Measure the thickness of the material you are using with the thickness gauge.
- Set the drill bit depth by using the hex wrench in the thickness gauge to set the collar on the drill bit.
- Place the workpiece in the jig and clamp with the Automaxx clamp.
- Using a power drill, drill pocket holes in the workpiece through the drill guides. ...
How to make pocket holes with KREG jig?
Supplies:
- Measure the Depth of your Wood Alright y’all, let’s get started with the basics. ...
- Set Your Kreg Jig Now that we know our board width it’s time to set up our little Kreg Jig! Don’t worry y’all this is super simple. ...
- Clamp your Wood and Kreg Jig Together
How do you adjust a Kreg k4?
0:051:03How To Set Up a Kreg Jig in Three Simple Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy just aligning that thickness mark and locking it down next you need to set the stop collar on theMoreBy just aligning that thickness mark and locking it down next you need to set the stop collar on the bit again you use the thickness. And line up the steps part of the bit. Then lock the stop collar.
How do I set the depth on my Kreg jig?
0:171:23Quick Tip: Set Up Your Kreg Jig® R3 in 3 Simple Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust slide the drill bit in move the stop collar. Until it aligns with the thickness that you need.MoreJust slide the drill bit in move the stop collar. Until it aligns with the thickness that you need. And then tighten it down now you're all set to drill pocket holes at the perfect depth.
How do you use the Kreg pocket hole jig k4?
1:083:04Kreg K4 Pocket Hole Jig - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're working with simply loosen the pin adjust. And lock in place your timber thickness also helpsMoreYou're working with simply loosen the pin adjust. And lock in place your timber thickness also helps you select the correct screw length the drilling block has three holes in it for variable.
What depth should I set my Kreg jig for 2x4?
Match the line to the edge of the assembly for your material thickness setting. This one is set to 1-½” for drilling into a 2×4.
How do you adjust a pocket hole jig?
0:071:07Kreg® 300-Series Pocket-Hole Jigs: Adjusting Your Jig Stops - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's easy just squeeze against the jig. And slide the stop until it clicks into place.MoreIt's easy just squeeze against the jig. And slide the stop until it clicks into place.
How do you measure the depth of a pocket hole?
0:051:10Kreg® 300-Series Pocket-Hole Jigs: Check Your Material ThicknessYouTubeStart of suggested clipEnd of suggested clipYou just need the material thickness gauge that comes with the jig. Simply hold the jig along theMoreYou just need the material thickness gauge that comes with the jig. Simply hold the jig along the edge of your material. And it will show you what thickness range your material falls in once.
Is the Kreg k4 discontinued?
Availability: Discontinued.
How do you use a Kreg jig for beginners?
3:165:29How to use a Kreg Pocket Hole Jig 320 - For Beginners - YouTubeYouTubeStart of suggested clipEnd of suggested clipBelow. First I measured and marked the longboard for the location of the middle boards. And then IMoreBelow. First I measured and marked the longboard for the location of the middle boards. And then I attached them using wood glue and one and a quarter inch pocket hole.
What angle does a Kreg jig drill at?
a 15° angleAs you drill, the stepped drill bit enters the wood at a 15° angle. That's what creates the distinctive oval shape. The pocket-hole jig ensures this angle is consistent, and that the bit is held steady as you work — making the process of drilling an angled hole entirely foolproof.
Does Kreg Jig k4 work on 2x4?
The Kreg Pocket-Hole Jig HD is optimized for working with 2x4s and 1 1/2" thick and larger stock.
What do I set my Kreg Jig at for a 2x4?
Kreg AdviceThickness refers to the thickness of your boards. if you're joining 2x4's you'll want to set the jig at 1.5 inches and if you're joining 1x6 you'll set it at 3/4 of an inch. ... Set the clamp as well as the setting on your drill collar to the thickness of the wood.
What are the measurements on a Kreg Jig?
Kreg Mini SetupBoard ThicknessDepth CollarJig Distance From Edge1/2"3-5/16"1/4" Over3/4"3-1/2"0"1-1/2"4-1/4"1-1/4" Back
Kreg Jig Settings Chart and Calculator
DISCLOSURE: THIS POST MAY CONTAIN AFFILIATE LINKS, MEANING I GET A COMMISSION IF YOU DECIDE TO MAKE A PURCHASE THROUGH MY LINKS, AT NO COST TO YOU. PLEASE READ MY DISCLAIMER FOR MORE INFO.
Kreg Jig Settings Calculator
Use this calculator to determine the settings you need for your Kreg Jig and drill bit. It will also tell you what length screw works best for your wood thicknesses. Make sure to choose the correct joint type for your joint.