Set the Water Level knob to the Auto Sensing setting and the washer will fill to a level that ensures the load engages the agitator. From this point, the electronic control will sense the load and determine if additional water is needed. Your washer may go through a series of small fills to get to the appropriate water level.
Why does my Whirlpool washer not fill?
When this occurs, you’ll need to replace the part by following these steps:
- Unplug the machine and turn off all water lines.
- Disconnect the water hoses on the rear of the machine. ...
- Remove the drain line from the wall to prevent it from pulling tight.
- Lay the washer down on its front. ...
- The part you need to access is located under the machine.
- Remove the shield by unscrewing the top and bottom screws. ...
How to repair my Whirlpool duet washer?
How do I fix my f28 error on my Whirlpool Duet washer?
- Unplug the electrical cord from the wall outlet.
- Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
- Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
- Find the control console unit reset lever and pull it toward you.
Does this washer automatically adjust water level?
The most striking difference in this washer is the low-water washplate wash system (on some models). Most washers automatically adjust the water level to the load size; no water level selector is needed (on some models). For best performance, it is recommended to load items in loose heaps evenly around the washplate.
How can I Reset my Whirlpool duet washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
- The motor has now been reset and is ready for you to start a cycle.
How do I get my Whirlpool washer to fill with more water?
If you would like the machine to automatically sense the appropriate water level for the load size and type, turn the Water Level knob to the Auto Sensing setting. If you would like to add the maximum amount of water to your wash cycle, turn the Water Level knob to the Deep Water Wash setting.
Where is the water level switch on a Whirlpool washer?
Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.
How do I control the water level in my washing machine?
The level sensor uses a pressure switch to detect the water level in the tub. This switch controls how high the tub fills with water. The big end of the hose connects to the bottom of the tub, while the small end connects to the switch.
Why is my Whirlpool washer not filling up all the way?
CLEAN OR REPLACE THE WATER FILTERS (WATER INLET SCREENS) Clogged water filters or inlet screens can cause your washer to not completely fill with water. These small water filters are located in between the water hoses and the water inlet valve on the back of the washer.
How do you test a water level sensor on a Whirlpool washing machine?
1:134:05How to Test the Pressure Switch on your Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that's a good reason if you do not get that reading when you hear the diaphragm inside theMoreSo that's a good reason if you do not get that reading when you hear the diaphragm inside the pressure switch click then the pressure switch is bad.
What is a water level switch?
These devices equip electrodes to detect liquid levels. They have been widely used in water works and sewers for buildings and housing complexes, industrial facilities and equipment, water treatment plants and sewage treatment facilities, and many other applications.
Do washing machines have a water level sensor?
These sensors identify a minimum and maximum level for various cycles to ensure the appropriate amount of water depending on your laundry load. This auto-sensing technology usually works out pretty well, but it can malfunction. Typically, it malfunctions in the sense that the machine overflows.
Why do HE washers use so little water?
HE washers offer more capacity than traditional machines, because they don't have a large agitator and they use less water. Washing more clothes at once means doing fewer loads!
Why is my washing machine not filling up with water?
0:187:25Washer Won't fill? - Top 5 Problems and Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne is located in the end of the fill hose. And the other is inside the inlet valve itself if theMoreOne is located in the end of the fill hose. And the other is inside the inlet valve itself if the washer won't fill it could be that the screens are clogged. So take your fill hoses.
How do you reset a Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.
How to test water level switch?
Pull the wires off the water level switch to expose the connectors. Set a multimeter, a device used to test electrical current, to the X1 setting. Touch one probe to the first connector and the other probe to one of the two others. Test in pairs. You should always receive a reading of infinity or zero. Otherwise, remove the switch and replace.
Why does my washing machine flood?
Too much water may cause flooding. Washing machines fill with water during the wash cycle. To prevent overflowing, or too much water from entering the tub of the machine during the wash cycle, a water level switch is installed. The water level switch is connected to the console with a tube running down into the machine.
