Use star washers under the bolts and you'll find a 3/8" ratchet with a 12" extension will make life a whole lot easier. Now, to align the blade to the slots turn the saw on it's back end, so you can see the bolt holes and still measure to the miter slots.
How do you align a craftsman table saw?
The nine steps to a perfectly tuned tablesaw
- Align the drive pulleys. If you have a direct-drive saw, you obviously can skip this step. ...
- Level the table insert. ...
- Level the extension wings. ...
- Check the blade for alignment with miter slots. ...
- Align the blade parallel with the miter slots. ...
- Set the bevel stops. ...
- Adjust the blade guard and splitter/riving knife. ...
- Set the miter gauge. ...
- Align the fence. ...
How to make a table saw alignment tool?
Table Saw Class
- Easy Table Saw Sled: 16 Steps (with Pictures) Easy Table Saw Sled: A table saw sled (or cross cut sled) makes cutting wood against the grain safer, and much easier.
- SawStop Outfeed Extension. ...
- DigiAlign-Table-Saw-Jointer-Drill-Press-and-Router-Alignment-Tool. ...
- Shop Notes Box Joint Jig. ...
- Thin strip rip jig for the table saw. ...
How to adjust a craftsman table saw blade?
How do you align a Craftsman table saw?
- Click any image to view a larger version.
- To align the blade at 90°, shift the rear trunnion bracket left or right until the blade is perfectly parallel to the saw's miter slot.
- To align the blade at 45°, lower one or both trunnion brackets by inserting shims under the table. This brings the blade back into alignment.
How to align a table saw?
Tools & Supplies
- Table Saw (I’m guessing you have one of those since you clicked on this post … )
- Framing Square
- Speed Square
- Combination Square
- Level
- Lumber for test cuts
How do you adjust the alignment on a table saw?
4:186:29How to Align Your Table Saw Blade for Safe and Clean Cuts - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe way we're going to do that is by loosening the three bolts in these corners and leaving thisMoreThe way we're going to do that is by loosening the three bolts in these corners and leaving this back corner tight to act as a pivot. I'm going to tap. That front corner of the table.
How do you square a Craftsman table saw fence?
0:522:56Craftsman 10” Table Saw Fence Setup Tutorial CMXETAX69434502YouTubeStart of suggested clipEnd of suggested clipUp where your red hash mark lines up with in this case the 12-inch. Position you've got 12 inches onMoreUp where your red hash mark lines up with in this case the 12-inch. Position you've got 12 inches on the right side of the saw. Ten inches on the left side of the saw that you can measure to.
How do you realign a table saw blade?
2:306:22How To Align a Table Saw Blade to Miter Slot and Fence - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the blade is off by the same amount at both 90 degrees and 45 degrees then the table simply hasMoreIf the blade is off by the same amount at both 90 degrees and 45 degrees then the table simply has to be moved sideways to align the miter slot and the blade.
How do you adjust the trunnion on a table saw?
13:4815:46Table saw not working right? The proper way to adjust/align it...YouTubeStart of suggested clipEnd of suggested clipProcess than the cabinet. Saw in this case you'll place your shims between the trunnions on theMoreProcess than the cabinet. Saw in this case you'll place your shims between the trunnions on the underside of the table. Either the front two or the back.
How do I make my table saw fence accurate?
1:023:59How to Align Your Table Saw Fence | Rockler Skill Builders - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo do this simply place your finger on the sidewall of the miter saw it closest to the fence. NextMoreTo do this simply place your finger on the sidewall of the miter saw it closest to the fence. Next slide the fence over until the face of the fence is flush with the side of the miter slot.
How do you calibrate a table saw fence?
0:324:524 Easy Ways to Align a Table Saw Fence - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis first method is probably the easiest. Even if it's not the most exact. Put a combination squareMoreThis first method is probably the easiest. Even if it's not the most exact. Put a combination square in your miter track pressed against the edge of the track then lock your fence next to the ruler.
How do you adjust the blade on a old Craftsman table saw?
0:141:38How to Adjust a Craftsman Table Saw Blade - YouTubeYouTubeStart of suggested clipEnd of suggested clipTighten the blade-tilt locking knob raise. The blade to its highest cutting position push the redMoreTighten the blade-tilt locking knob raise. The blade to its highest cutting position push the red button on the blade guard and lift off the blade guard assembly mark.
Why is my table saw not cutting straight?
2:599:59Why Does My Table Saw Not Cut Straight? - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst of all you need to make sure that your fence is exactly perpendicular or a 90 degree angle toMoreFirst of all you need to make sure that your fence is exactly perpendicular or a 90 degree angle to the surface of the saw to the table. Top. This is not an easy thing to adjust. But it is adjustable.
Where is a trunnion on a table saw?
3:047:14MAGNIFICENT DIY Table Saw with Trunnions - YouTubeYouTubeStart of suggested clipEnd of suggested clipTrunnions are basically concentric guides with their center point right at the surface of theMoreTrunnions are basically concentric guides with their center point right at the surface of the tabletop.
What is a trunnion on a table saw?
In a table saw, it is the attachment point of the Circular Saw 's Arbor to the underside of the table. The primary adjustment point for aligning the saw blade to the miter slot on the top of the saw's table, the Trunnion also handles the adjustment of the angles of the Blade .
How do you check the accuracy of a table saw?
0:008:13Table Saw Accuracy - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe blade square to the table and the fence squared of the table. The first step is to check to makeMoreThe blade square to the table and the fence squared of the table. The first step is to check to make sure that the miter slot and the blade are parallel.