Stir product occasionally throughout application. Use a 3/8” nap roller, nylon/polyester brush, pad applicator or airless sprayer. Airless spray is recommended for experienced applicators only; use a.015 -.019" tip.
Why choose Behr premium ® semi-transparent stain&sealer?
WHY CHOOSE BEHR PREMIUM ® SEMI-TRANSPARENT STAIN & SEALER? Our most advanced formula weathers it all. Behr’s Semi-Transparent Stain is formulated to protect wood from drying out and cracking under direct sunlight, keeping your deck looking great summer after summer. Our water resistant formula ensures that surface water beads on contact.
Does Behr premium weatherproofing stain work on mold?
– Behr Premium Weatherproofing Stain had some mold growing on the flooring near the home and on top of the rail cap. – Applying the Behr Premium Stain is like painting your deck except it does not apply evenly.
Is Behr premium stain like painting a deck?
– Applying the Behr Premium Stain is like painting your deck except it does not apply evenly. We have stained 1000’s of decks and have never found a stain to be more difficult to apply than Behr. It dries extremely fast and will show overlaps if not careful.
Can you use Behr stain on wood?
Use a product such as BEHR PREMIUM® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood. BEHR PREMIUM® NO. 63 All-In-One Wood Cleaner MUST be used following NO. 64 to clean, brighten & neutralize wood.
See more
How do you apply semi-transparent stain and sealer?
0:532:22How to Apply a Clear, Toner or Semi-Transparent Wood StainYouTubeStart of suggested clipEnd of suggested clipApply one thin coat with a high-quality brush roller paint pad or by spray equipment. To help avoidMoreApply one thin coat with a high-quality brush roller paint pad or by spray equipment. To help avoid lap marks. Apply to a few boards at a time keeping a wet edge. Always back brush for best results.
How do you spray Behr semi-transparent stain?
0:200:52BEHR® Paint | How to Apply Stain - YouTubeYouTubeStart of suggested clipEnd of suggested clipApply the stain evenly in the direction of the grain. Two or three boards at a time moving from endMoreApply the stain evenly in the direction of the grain. Two or three boards at a time moving from end to end we know this seems obvious.
Does Behr stain need 2 coats?
Over application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily. Two thin coats required.
How long does it take for Behr waterproofing stain and sealer to dry?
Wait 24-48 hours before light foot traffic. 72 hours for full cure.
How do you spray Behr stain and sealer?
0:321:05BEHR Stain & Finish Project How To's: Fences - YouTubeYouTubeStart of suggested clipEnd of suggested clipApplication apply finish following the grain of the wood working. From top to bottom make your oldMoreApplication apply finish following the grain of the wood working. From top to bottom make your old sense look beautiful. It's easy with the right bear. Products you.
How long does it take for Behr semi-transparent stain to dry?
1-2 hours before recoat. Allow 72 hours for full cure.
How long does Behr waterproofing stain and sealer last?
BEHR PREMIUM® Solid Colour Waterproofing Stain & Sealer. Protect and beautify with BEHR PREMIUM Solid Colour Weatherproofing All-In-One Wood Stain & Sealer. This 100% acrylic formula seals out the elements, and the sun's harmful UV rays, for up to 10 yrs. on decks and up to 25 yrs.
Do you need two coats of semi-transparent stain?
Skip a Second Coat With a solid stain, CR typically recommends putting on two coats because these are more like a regular paint and will dry one on top of the other. But with a clear or semi-transparent wood stain, a second coat will just sit on the surface of the first coat.
How long should you wait to apply second coat of stain?
How Long to Wait Before Second Coat of Stain. Wait an hour before applying a second coat of standard wood stain. You may need to wait for longer for gel stains—about six to eight hours before adding a second coat. In any case, the product label should always indicate how long for stain to dry before the second coat.
How long does Behr semi-transparent stain last?
This 100% acrylic formula seals out the elements, and sun's harmful UV rays, for up to 6 yrs. on decks and up to 8 yrs. on fences & siding. It's available in 60 custom colors to help you create a look that's as beautiful as it is durable.
Is Behr semi-transparent waterproofing stain and sealer oil-based?
BEHR Premium Semi-Transparent Waterproofing Wood Stain & Sealer is a penetrating oil-based stain that beautifies and protects your exterior wood surfaces. This product is available in popular exterior premix colors and can also be tinted to a range of other exterior colors.
How long should Behr paint dry before second coat?
After your first coat of paint is dry, it's safe to recoat typically after four to six hours. A good rule of thumb is to wait at least three hours to recoat your paint or primer if it's water-based. Waiting 24 hours is best for oil-based paint and primer.
Is a second coat of stain necessary?
We always recommend two coats of stain for any wood project, but you should only apply as much stain as the wood can absorb. Extremely dense hardwoods may only be able to absorb one coat of wood stain. The general rule of thumb is to apply only as much as the wood can absorb.
Should you stain wood twice?
For one thing, it'll take a long time to finish the project. You have to wait for each layer of stain to completely dry before adding the next. Otherwise, the new coat will dissolve the previous coat and you'll have a real mess on your hands.
Will more coats of stain make it darker?
Apply a second coat of stain after the first has dried fully. This will usually produce a darker coloring, but it adds a step to the process and slows production. Substitute a glaze or gel stain for the liquid stain. Glazes and gel stains usually contain a higher ratio of pigment.
Do you sand between coats of stain?
Note: Sanding between coats is not necessary, but it will provide a better finish. After a coat has dried, use 220 or 240 grit sandpaper or extra fine steel wool to lightly sand surface. This will ensure good adhesion of the succeeding coat.
How long is Behr Process Corporation warranty?
Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 8 years on vertical surfaces and 6 years on horizontal surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Color fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. This warranty excludes (1) labor and costs of labor for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Note to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. To obtain warranty service, call 1-800-854-0133. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
How long does acrylic sealer last?
Enhance your wood's natural patterns while providing increased protection from the elements. This 100% acrylic formula seals out the elements, and sun's harmful UV rays, for up to 6 yrs. on decks and up to 8 yrs. on fences & siding. It's available in 60 custom colors to help you create a look that's as beautiful as it is durable.
What is the best product to remove latex and acrylic paint from wood?
Use a product such as BEHR PREMIUM® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
How to prevent lap marks on wood?
Apply product end-to-end or to board lengths to prevent lap marks. Over application of stain will lead to surface failure including peeling and cracking. Avoid applying stain too heavily. For optimum performance, coat all six sides of wood.
What is the best product to remove mill glaze?
On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood. Lightly sand to remove remaining wood fibers/fuzz.
How to get rid of lap marks on board?
Maintain a wet edge when applying. Apply product end-to-end or to board lengths to prevent lap marks.
How long does a Behr stain last?
How a stain wears is also really important. I tell my clients to expect Behr to last them 3-5 years here in Minnesota. We have rather harsh weather and I consider 3-5 years a success on a deck.
How long does it take for Behr deck stain to dry?
How Long Does Behr Deck Stain Take To Dry. From my experience, Behr Deck Stain is typically dry to the touch in about 30 minutes. It typically needs 1-2 two hours before you can re-coat and 72 hours before full traffic on your deck may resume.
What is Behr deck over?
Behr Deck Over is a solid deck stain that goes on incredibly thick and is only meant for covering up decks where the wood is in terrible shape.
What does it mean when a deck stain is peeling?
Many deck stains will start to peel or wear very unevenly. Peeling means that it never absorbed into the wood and when you apply your new stain, it will look blotchy and uneven.
How do I remove stain from a deck?
Power washing and sanding are great ways to remove existing deck stain. Behr also makes a chemical stain stripper called Behr Wood Stain and Finish Stripper. Personally, I like to power wash, then sand the deck with a random orbital sander and finish using Wood Stain and Finish Stripper if needed.
What size brush should I use to stain a deck?
I always apply my deck stains with a thick 4″ deck brush. Deck brushes are made to hold a lot of stain, allow you to apply stain quickly, and allow for the most control (and best finish in my opinion).
When to use solid deck stain?
I recommend using solid deck stain when your old stain is blotchy and uneven, but the wood is still in good shape.
Where is Behr Process located?
To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty. Read Warranty Information.
How long is Behr Process Corporation warranty?
Behr Process Corporation warrants to you, the original residential consumer purchaser, the performance of this product as described on this label for 8 years on vertical surfaces and 6 years on horizontal surfaces, from the date of purchase. THIS WARRANTY IS NOT VALID WHEN THE PRODUCT IS NOT PROPERLY APPLIED TO A PROPERLY PREPARED SURFACE OR CARED FOR IN ACCORDANCE WITH THE LABEL DIRECTIONS. Color fading and slight natural graying of the wood may occur during the warranty period, especially in areas exposed to heavy foot traffic or excessive weather. This warranty is not transferable. If this product is found not to perform as specified on the label during the warranty period, Behr Process Corporation will, at its option and upon presentation of proof-of-purchase (the original receipt), either furnish an equivalent amount of new product or refund the original purchase price of this product to you. The clause of limitation of liability which follows is inapplicable in Québec. This warranty excludes (1) labour and costs of labour for the application or removal of any product, and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. The above provisions are not intended to operate where prohibited by law. This limited warranty is the only warranty provided by Behr Process Corporation unless extended by a provincial consumer statute. To obtain warranty service, call 1-800-854-0133 ext. 2, or contact Behr Process Corporation at 2750 Centre Avenue N.E., Calgary, AB T2A2L3. Behr Process Corporation reserves the right to inspect any and all application of the product prior to processing your claim made under this warranty.
How to remove stains from wood?
Preparation#N#Blank space if empty. 1 Use a product such as BEHR PREMIUM ® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood. 2 BEHR PREMIUM ® NO. 63 All-In-One Wood Cleaner MUST be used following NO. 64 to clean, brighten & neutralize wood. 3 When NO. 64 is not needed, use a product such as NO. 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold, mildew, algae & fungus. Rinse thoroughly and allow to dry before coating. 4 On new wood, use a product such as NO. 63 to remove mill glaze and open the pores of the wood. Lightly sand to remove remaining wood fibers/fuzz.
What is semi gloss sheen?
A semi-gloss enamel sheen is sleek and radiant with a hard, durable finish. It is formulated to withstand wear, and will also resist moisture, fading and stains.
What is the best product to remove latex and acrylic paint from wood?
Use a product such as BEHR PREMIUM ® NO. 64 Wood Stain & Finish Stripper to remove loose wood fibers, latex, oil-based and 100% acrylic coatings on new or weathered wood.
What is satin enamel sheen?
A satin enamel sheen has a pearl-like finish that's easy to clean.
What is matte sheen?
A matte sheen has a low-luster, reflective finish that is durable, easy to clean, touches up well and also hides minor surface imperfections.
