Rustoleum Blacktop Driveway Sealer
- Clean the surface - I used a gas powered leaf blower, you can use a stiff bristle broom.
- Open a bucket of Rust-Oleum® EPOXYSHIELD® Blacktop Coating. Use a drill with a stirring attachment to mix the acrylic...
- Bring the bucket to the work area of the blacktop. You can dip the roller into the bucket and apply to the driveway, or...
How do you apply a driveway sealer?
Allow the entire driveway to dry once you've spread the first coat from the home-end of your driveway to the street-end. Apply the second coat by pouring more strips across and spreading them down the driveway like before.
How do I remove oil spots from my Driveway before sealing?
If there are oil spots on your driveway, wash the areas with an asphalt degreaser the day before applying driveway sealcoating. Trim any nearby shrubs with a trimmer and, if you have grass growing alongside your pavement, trim the edges near the asphalt using an edger. Tape all surfaces adjacent to the pavement to protect them from the sealer.
What is the warranty on Rust Oleum ultimate driveway sealer?
About Rust-Oleum Ultimate Driveway Sealer Solarlock Technology uses the power of the sun to lock in the Ultra Black Finish with unparalleled fade resistance, keeping your driveway beautiful and protected for over 15 years. 15 Year Warranty
How do you use Rustoleum paint on Blacktop?
Open a bucket of Rust-Oleum® EPOXYSHIELD® Blacktop Coating. Use a drill with a stirring attachment to mix the acrylic thoroughly with the rubberized polymers. Or use a paint stick; either way it mixes easily. Bring the bucket to the work area of the blacktop.
What is the best way to apply driveway sealer?
0:331:49Driveway Sealer - How To Apply - Menards - YouTubeYouTubeStart of suggested clipEnd of suggested clipSpread the sealer out at a 45 degree angle to get a thin coating. And make a pass back over for aMoreSpread the sealer out at a 45 degree angle to get a thin coating. And make a pass back over for a smooth finish. Continue this process until your entire driveway is sealed.
What is the best way to apply asphalt sealer?
0:526:18How to Apply a Driveway Sealer - Sealing a Driveway - YouTubeYouTubeStart of suggested clipEnd of suggested clipProduct. So you can either use just a piece of wood. And go after it or you can use a mixer on aMoreProduct. So you can either use just a piece of wood. And go after it or you can use a mixer on a drill. And I like this method. It does a nice job but take the time to do it a full 5. Minutes.
How many coats of sealer should you put on your driveway?
two coatsMost driveway sealer manufacturers recommend two coats with a minimum drying time of eight hours between coats, so this driveway sealing project will fill an entire weekend. The best asphalt driveway sealer materials cost about $100, but you'll save about $200 in labor over a professional job.
Can you use a roller to apply driveway sealer?
If you're applying an acrylic-based driveway sealer, which is designed for concrete or masonry surfaces, it can be applied with a roller. If you're applying an asphalt-based product, however, it must be applied with a squeegee.
Is it better to brush or squeegee driveway sealer?
Squeegee applications typically produce a better bond between the pavement's surface and the sealant. The pressure exerted by the squeegee forces the sealant into surface cracks and voids, creating a bond that is of higher quality while often yielding a smoother appearance.
Is it better to spray or squeegee driveway sealer?
Which Is Better? Squeegee and spray application sealcoating each have their pros and cons. Spraying is a much faster way to apply the sealer, and crews can cover larger lots and in a fraction of the time it takes to use a squeegee.
How much does a 5 gallon bucket of driveway sealer cover?
between 250-500 square feetAsphalt Sealer Prices Note: The typical 5-gallon sealcoat container can cover between 250-500 square feet depending on the material's condition and texture. For simplicity's sake, these examples use five gallons that cover the maximum 500 square feet.
Why did my driveway sealer peeling off?
Peeling is caused by sealcoating not bonding to oil spots or any other surface contaminants like dirt, grease, etc. or oxidized pavements. Prior to sealcoating application, the pavement surface shall be thoroughly cleaned, oil spots be treated with an oil spot primer.
How long should I wait between coats of driveway sealer?
Under ideal conditions, typically we recommend waiting 4-12 hours, and until the first coat is fully dry and cured all the way through the film. In optimal conditions, if the driveway is sealed early in the morning and the entire driveway is in full sun and is fully dry, you may apply a second coat the same day.
What type of roller do you use for driveway sealer?
Applying the Sealer With a Driveway Roller Use a 3/8-inch nap paint roller to apply the sealer. Stir the can of sealer with a clean stick before you begin so it's thoroughly mixed. Starting at the back center of the driveway, pour enough sealer directly onto the surface to coat at least a 10-foot by 10-foot area.
Should you wet driveway before sealing?
Plan for the Weather Make sure there is no forecast for rain for at least three days. You want the driveway to remain dry for at least one day before and one day after applying each layer of sealant. Avoid temperatures above 95 degrees Fahrenheit. This can cause the sealant to dry too fast.
Do you have to clean driveway before sealing?
Prep the driveway for sealing The last step before applying a sealer is to thoroughly clean the driveway. Start with a push broom and sweep away the heaviest debris. Then use a garden hose, or better yet, a pressure washer to rinse the surface clean of all loose dirt, sand, and grit.