![image](http://www.doityourself.com/forum/attachments/basements-attics-crawl-spaces/7365d1357165262-hanging-drywall-concrete-basement-wall-camerazoom-20130102170359038.jpg)
How do you install a stringer?
- Get the stringer. ...
- Find your studs. ...
- Position the stringer where you want to install it.
- Drill through the stringer and into the studs behind it.
- Using lag screws, screw the stringer into your studs. ...
Can you install ledger board before stair hangers?
Can you use a hammer drill to connect stair stringers?
About this website
![image](https://www.trainqsc.com/uploads/1/1/9/1/119121911/img-20181214-100339.jpg)
Attach stringers to cinder block wall? | DIY Home Improvement Forum
Replacing old concrete steps with PT stringers w/composite treads. I will have 6 (4 step) stringers that need to attach to cinder block wall. Should I install a 2x10 ledger board and use joist hangers or can I install joist hangers directly to wall w/tapcons?
Can you install ledger board before stair hangers?
You can then slide a stair stringer in place and fasten it, using nails or screw fasteners. You don't need to install ledger board before the hangers, which will save you time and money during the project. Advertisement.
Can you use a hammer drill to connect stair stringers?
A hammer drill will allow you to connect stair stringers with ease. Several building manufacturers make hangers that you can use to fasten stair stringers to concrete. These hangers are adjustable to fit most types of wood structured stairs.
Where is the stringer mounted?
In the above image, the stringer is mounted outside the drywall- this is normally how stringers are used when they are used to mount wall mounted rigs and racks.
What is a stringer board?
A stringer is a board mounted horizontally and screwed into studs, that something else is then mounted to. For example, stringers are used in home construction to provide more support or strength for stair installation or bathtub installation (or pull-up bar, squat rack, or rig installation in your garage gym.)
Why do we use stringers to mount pull-up rigs, squat racks, and pullup bars?
Stringers increase structural strength in many cases- for example, spanning studs with a stringer, then mounting a rig into the stringer makes for a more secure installation
How long is a pull up stringer?
We typically recommend a 2x10" stringer for wall mount pull-up rig installation (with the length depending on the length of your wall-mount rig), two five foot long 2x6" stringers for our retractable pull-up racks, and usually 1-2 2x4" stringer (s) of about four feet in length are good for pullup bars. You can find this lumber at your local home supply store.
How many inches are studs?
Studs are generally installed in 16 or 24 inch intervals, but some older construction does not adhere to this spacing paradigm. In this case, you would install your stringers into the studs, then your pull-up rig into the stringer. Please note:
Do you need a stringer on a pull up bar?
As long as both sides of the pull-up bar are mounted to a stud, a stringer shouldn't be necessary. However, using a stringer would still provide better stability as the stringer would equally disperse the force being emitted on the pull-up bar equally to the two studs.
Can you install ledger board before stair hangers?
You can then slide a stair stringer in place and fasten it, using nails or screw fasteners. You don't need to install ledger board before the hangers, which will save you time and money during the project. Advertisement.
Can you use a hammer drill to connect stair stringers?
A hammer drill will allow you to connect stair stringers with ease. Several building manufacturers make hangers that you can use to fasten stair stringers to concrete. These hangers are adjustable to fit most types of wood structured stairs.
![image](https://4.bp.blogspot.com/-HBb0URr0M0I/T3glq6KeMCI/AAAAAAAAAHc/u1fJMKhafcI/s1600/ShapeBeam2.jpg)