Instructions for How to Attach Fascia Board to Roof Trusses
- Remove old fascia boards including old nails that are sticking out.
- Starting at a roof corner, lift the first board into place and hold its top edge tightly against the bottom edge of the roof deck.
- Mark the place closest to the end of the board that aligns with the center of a joist.
How is fascia attached?
The fascia board is nailed to the rafter feet and usually has a rebate or lip for the soffit boards to slot into. They are then either fixed to a batten that is attached to the brickwork, or sat on top of the last course of brickwork.
What kind of fasteners should be used to attach fascia?
Trex recommends the use of Starborn® DeckFast® Fascia System, SplitStop™ Fascia Screws or Simpson Strong-Tie® Fascia Board Screws, for all composite Trex fascia profiles. For near water applications, you can also use Fascia System HeadCote® stainless steel screws.
How do you attach wood fascia?
2:359:45You put the one side of the fascia. Board up on the l bracket that we made. And then you just grabMoreYou put the one side of the fascia. Board up on the l bracket that we made. And then you just grab the other side as you just see me do there and carry it up the ladder.
Do you nail or screw fascia board?
I usually use stainless steel screws, but use hot dipped galvanized nails on occasion. Galvanized Nails are what's traditionally used. If you're going to use screws (star head) then make sure that it's protected from rusting out.
Should fascia be face nailed?
Never face nail fascia. *Keep nails lined up with soffit V-grooves for best appearance. Nail every 24", but do not nail too tight. Nails should penetrate a minimum of 3/4" into nailing surface.
Can I use screws for fascia?
0:321:07Your fascia board will hang from the screws. And thus can expand and contract if. You're using aMoreYour fascia board will hang from the screws. And thus can expand and contract if. You're using a standard deck screw then when you're faced your board expands.
What nails do you use for fascia?
What nails do you use for fascia?Galvanized nails.Aluminum nails.Stainless steel nails.
Can you use roofing nails for fascia?
Use 1 ½” roofing nails to install soffit. Use white panel nails to install aluminum fascia. Use tin snips to cut F-channel, vinyl soffit, and aluminum fascia. against the house to hold one side of soffit.
Should there be a gap between roof and fascia?
Ideally, there should be no gap between the fascia and the gutter. Any gap between the two will cause wind-driven rain to get to the fascia and travel down your house. What is this? The water can find its way into your soffit or down your walls, creating the perfect habitat for mold.
What goes on first roof or fascia?
Fascia and soffit are installed after the roof installation is finished. It is ideal that soffit and fascia materials be installed before you place tiles or any other type of roofing material on the roof. There are different types of finished and variations that can be used for the soffit.
Do you nail drip edge into fascia?
Tack the end into position with the roofing nails and press the nail within the drip edge and into the roof covering. But do not push it through the fascia. Arrange the shingles back into position as you continue along.
How far apart should fascia screws be?
The maximum spacing between the fascia fasteners is 18”. Using a 3/16” wood pre-dill bit, drill one hole in the middle of the spacer. Place a single fastener in the pre-drilled hole of the spacer and tighten until the fastener indents into the spacer. Do not over tighten as it could split the spacer.
What kind of nails should I use for fascia?
Aluminum Finish White Nails from Amerimax Home Products are designed for outdoor applications such as securing soffit, fascia, trim coil and roof drainage installations.
What type of screws are recommended to be used when attaching fascia brackets to the fascia board?
RECOMMENDED: Use two 25mm x 5mm roundhead brass or zinc screws when fitting fascia brackets.
What nails do you use for metal fascia?
Use white panel nails to install aluminum fascia. Use tin snips to cut F-channel, vinyl soffit, and aluminum fascia.
How do you fasten steel fascia?
1:052:19The tab should fold over towards the gable side of your roof. Fasten the lower section of fasciaMoreThe tab should fold over towards the gable side of your roof. Fasten the lower section of fascia wrap with screws 12 inches on center overlaps a fascia trim should be a minimum of six inches.
Can you remove a roof overhang?
Replacing a roof overhang involves removing fascia and soffit materials. Applying sealant coatings to the new pieces can help prolong the life of a new overhang structure. Replacing a roof overhang involves dismantling the fascia and soffit.
Can you cut the overhang off a truss?
Most truss manufacturers now have the equipment which allows them to precession cut and trim most any truss member by using component saws. Strangely, some of them still leave the “tails” of the trusses square on the overhanging end, rather than plumb cutting.
What is the minimum roof overhang?
Overhangs can vary from a few inches to a few feet depending on preference; however, the suggested width of an overhang is between 12” and 18” for eaves and no more than 8” for rakes. That said, overhangs can extend as far as 2′ without the need for external supports.
How much overhang should a tin roof have?
A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
What is the underside of a roof overhang called?
The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”. The soffit is basically, any finishing material, such as wood or fiber cement, that is installed to cover the underside of your roof overhang.
Can I cut off rafter tails?
Cut each rafter tail at the cut lines, using a circular saw. Once cut, the rafter tails are ready for installation of the fascia boards and roof sheathing.
How do you attach fascia to rafters?
Mark the place closest to the end of the board that aligns with the center of a joist. Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place.
