How to Bind a Potholder?
- Step 1: Prepare the Layers Use scraps to cut out the top of a potholder. ...
- Step 2: Quilt or Trim the Corners Now, you have to trim the corners. ...
- Step 3: Pin Binding Next, open the binding and start wrapping it around the potholder edge. ...
- Step 4: Sew Binding The pins will hold the layers sturdily. ...
- Step 5: Make the Loop
Full Answer
How do you bind a pot holder with bias binding?
Unfold the bias binding and line up the edge with one corner of the pot holder of the backing side of the pot holder. Pin the binding along one edge of the pot holder. Sew the binding along that side in the first crease. Stop approximately 3/8″ away from the end of the fabric, and back-stitch or sew a locking stitch.
How to make a potholder?
How to make the potholder. Step 1. Layer your fabric pieces; the top fabric inner pieces /batting and the back piece should be layered and then quilted together Step 2. Take your bias tape and keep the edge ( any edge) of the potholder inside the bias tape and stitch from the top. Step 4. Stitch in place.
How do you sew a potholder with a sewing machine?
Sew along the open, long edge on your sewing machine using a straight stitch and a matching thread color. Fold the bias tape in half so that the narrow ends touch. Tuck it under 1 of the bias-taped corners on your potholder and secure it with a pin. The ends of the loop should touch the raw edges of your potholder.
How do you quilt a pot holder?
Quilt or sew through all of the layers in your preferred pattern eg horizontal, vertical or diagonal lines, stippling, or following the lines of the quilt block. Also sew around the outside of the pot holder, approximately 1/4″ from the edge of the top fabric – this will make binding the pot holder easier.
How to Bind a Potholder?
Which side should a potholder be layered on?
How to cut out the top of a potholder?
What is a potholder quilt?
How to make a binding section sharper?
How do you bind potholders?
6:1313:43How to Make a Pot Holder With Binding | The Sewing Room ChannelYouTubeStart of suggested clipEnd of suggested clipAnd place your binding down and then pin it in place. And pin across then from this side of the potMoreAnd place your binding down and then pin it in place. And pin across then from this side of the pot holder. From this edge right here. You're going to stitch into that corner.
What kind of interfacing do you use for potholders?
Insul-Bright is a needle-punched polyester insulating material. It is made of double-sided hollow polyester fibers with a reflective, metallicized poly center. This makes it ideal for potholders, table pads, oven mitts, ironing board covers, casserole cozies, baby warmers and more.
How wide is binding for potholders?
0:189:05How to Machine Bind a Potholder with a Hanging Loop - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor quick and easy projects to get the binding done quickly in order to do this you will cut yourMoreFor quick and easy projects to get the binding done quickly in order to do this you will cut your binding strips the strip two and a half inches wide.
Is one layer of Insul-bright enough for a potholder?
Use two layers of Insul-Bright to make your potholders extra heat-resistant. The Insul-Bright product directions state that it doesn't matter which side faces out, but I always place the two metallic sides facing the outsides of the potholders.
What is the best batting for potholders?
Insul-BrightThe best batting for pot holders is Insul-Bright, specifically because it is heat resistant. Quilt batting will also do. Honestly, you can use a wide variety of materials, such as heavy duty denim, drop cloths, or old dish rags. Just avoid using any lightweight fabrics.
What is the best material for potholders?
Popular fabric for pot holders is the cotton you find in the quilting fabrics. Make sure it is 100% cotton (no synthetic fibers that can melt). Other plant-based fibers such as linen or hemp will work but they are more expensive and do not come in all the fun patterns you can find in the cottons.
What material is inside a potholder?
A pot-holder is a piece of textile (often quilted) or silicone used to cover the hand when holding hot kitchen cooking equipment, like pots and pans. They are frequently made of polyester and/or cotton. Crocheted pot-holders can be made out of cotton yarn as a craft project/folk art.
How do you make a potholder without binding?
0:327:13No Binding Hanging Pot Holder - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll need one piece that is one and a half inches wide by five inches long and then you're goingMoreYou'll need one piece that is one and a half inches wide by five inches long and then you're going to need two 8 inch squares of cotton batting.
Do you have to use cotton thread for potholders?
When you make pot holders you want to make sure all of your supplies (thread, fabric, and batting) are 100% Cotton. If you use polyester fabric, and they catch fire, the fabric would melt. If cotton fabric catches fire it will just smolder.
Do you need to use batting with Insul-Bright?
Pro Tip: Insul-Bright is a specially made fabric that reflects hot and cold energy back to itself. This material needs to be used with at least one layer of cotton batting in order to absorb condensation.
Is there a right side to Insul-Bright?
If you are using the woven batting there is NO right or wrong side. If you are using an insulated batting with a clear visible metalized side called Therma-Flec, that would be the side you use to pick up your hot or cold items with, and you can cover the other side of batting with cotton fabric.
How do you make a heatproof potholder?
3:054:59How to make a pot holder or oven mitt - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a marker here but use something that won't show up as bright fold. In one of the short sidesMoreUsing a marker here but use something that won't show up as bright fold. In one of the short sides about half of an inch away from that Center mark and pin it in place.
How do you make a heatproof potholder?
3:054:59How to make a pot holder or oven mitt - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a marker here but use something that won't show up as bright fold. In one of the short sidesMoreUsing a marker here but use something that won't show up as bright fold. In one of the short sides about half of an inch away from that Center mark and pin it in place.
Do you need to use batting with Insul-Bright?
Pro Tip: Insul-Bright is a specially made fabric that reflects hot and cold energy back to itself. This material needs to be used with at least one layer of cotton batting in order to absorb condensation.
What material is inside a potholder?
A pot-holder is a piece of textile (often quilted) or silicone used to cover the hand when holding hot kitchen cooking equipment, like pots and pans. They are frequently made of polyester and/or cotton. Crocheted pot-holders can be made out of cotton yarn as a craft project/folk art.
How many layers of cotton batting are in a potholder?
Typically, two layers of batting are all you need for potholders. If you use cotton batting, you will need an extra layer. When you use Insul-Bright, two layers of batting are enough.
How to make a potholder with batting?
Step 1. Layer your fabric pieces; the top fabric inner pieces /batting and the back piece should be layered and then quilted together. Step 2. Take your bias tape and keep the edge ( any edge) of the potholder inside the bias tape and stitch from the top. I usually start from the middle of an edge.
How big is a potholder?
Note : Typically a potholder is an 8-inch square. But then it is your convenience.
How to make a binding strip?
Binding strip ( fabric cut in width of 1 1/2 inches and length equalling 4 * side length plus 3 1/4 inches. Fold the fabric strip 1/4 inch to the inside from both the sides. Press in place. Now press the strip by the middle. This is your binding strip.
Where to put bias tape loop?
You may want to keep a loop for hanging; insert it inside the bias tape edge.
Do you clip seam allowance before turning inside out?
Do not forget to clip the corner of your seam allowance before turning inside out – otherwise, your corners will not look as good.
Can you hang a pan with a loop?
If needed, you can also add a loop to hang it and keep it safe between holding pans and pots.
Can you do sashiko stitches after a potholder?
I have worked the sashiko stitches with the batting and top piece ; you can alternatively do the sashiko after the potholder is made and then these tiny running stitches will join the full layers of the potholder together
What is a potholder?
Potholders protect your hands while you handle hot pans and dishes during cooking or baking. There are lots of designs for potholders, but the most popular ones are the quilted kind and the woven kind. Both are easy to make, and once you nail down the process, you can make potholders for all sorts of gifts and occasions.
What fabric to use for potholders?
Use printed cotton to make season potholders. For example, use red cotton fabric with green Christmas trees to make Christmas potholders.
How to make a diagonal line?
6. Sew the diagonal lines using a straight stitch on a sewing machine. Start with the first line that you sketched, from the top-right corner to the bottom-left corner. Cut the thread, then do all the lines to the left of it, then all the lines to the right.
How far from corners should bias tape be?
Don't worry if the last set of lines are a little further than 1 inch (2.5 cm) from the corners. The bias tape will cover this up.
How to make a jar out of paper?
1. Cut a 9 in (23 cm) rounded square out of paper for the template. Use a pencil and a ruler to draw a 9 in (23 cm) square on a sheet of paper. Next, use a small jar as a stencil to round the corners. Cut the rounded square out when you’re done.
Where should the hook be on a loom?
Keep the hook woven across the bands. One end of the hook should be on the left side of the loom, and the other end of the hook should be on the right side.
Do you need to prewash a potholder?
If you don't plan on washing the potholder, then you don't need to pre-wash the fabric. If you do plan on washing the potholder, then you should wash, dry, and iron the fabric according to the instructions on the bolt. If you no longer have the instructions, look them up online based on the type of fabric you're working with.
How to make a potholder with binding?
Open binding and wrap around the potholder edge , starting at the center of one edge . Keep the binding fold centered on the side of the potholder , so that too much binding is not shifting towards the top or bottom of the potholder. You want the binding to be equal-width on both sides of the potholder to ease attachment.
How to secure corners of potholder?
To secure the corners, place pins perpendicular to the potholder corner. These pins will not go through all layers, so you'll need 3-4 pins per corner, some securing binding on the top side and some securing binding on the bottom side. Feel free to use as many pins as you like!
How to secure binding in place?
Use a pin oriented parallel to the potholder edge to secure binding in place. This pin should go through all potholder layers. Also, make sure the head of the pin is pointed to the right. This will make pins easy to remove when sewing.
How to make a quilt with batting and potholder?
Layer the pieces as follows: Backing (right side down), Heat-resistant batting (shiny side down), Regular batting and Potholder top (right side up). Center the potholder top on the other layers. Secure with basting pins, pinning through all layers to prevent shifting. Place a pin about every 2" in a gridlike pattern. If possible, place pins where they will not interfere with your first quilting lines.
What is a potholder quilt?
A potholder is basically a mini quilt with special heat-resistant batting. They're quick, useful and a great way to use scraps! The only tricky thing about potholders is the binding. Because they're so small, attaching traditional quilt-style binding is not such a fun process. This beginner-friendly tutorial shows how to finish potholder edges with store bought bias binding.
How to make a hanging loop for a binding?
Turn and loop the binding tail to make an attractive hanging loop. Pin the binding tail end at the zigzag binding seam.
How to hide raw end of binding?
Fold the cut, raw end of the binding tail towards the inner fold of the binding. Folding it back and into itself about 1/2" will hide that raw cut end. Pin binding closed at the end, with the raw edge tucked inside.
How to make a potholder?
How to Sew a Simple Potholder: 1. Cut out the following pieces from your fabric. You can decide which fabric designs to use on each part. cut two 9″ squares from fabric. cut two 9″ x 6 1/2″ rectangles from fabric. cut one 9″ square from thermal batting. cut one 9″ square and one 9″ x 6 1/2″ rectangle from quilt batting.
How to make a pocket piece with bias binding?
Add bias binding to one long edge of the pocket piece. Place one raw edge of the bias binding right sides together with the pocket edge. Stitch with a 1/2″ seam allowance, in the first fold of the bias binding. Press the binding up.
How long is a 1/2" double fold binding?
cut and make 1/2″ double-fold bias binding about 45″ long (2″ wide when unfolded)
Can you make bias tape for pot holders?
You also need to make your own bias tape. The bias tape that is most readily available at the craft store is a poly/cotton blend. It does not work for potholders! Bias tape is easy to make. If you need more detailed directions, you can look at my step-by-step bias tape post.
How to make a pot holder with binding?
For a simple pot holder with binding, you need 3 things: 1 Outer fabric made from natural fibres – quilting cotton is a great option.#N#Find kitchen-themed fabric at Fabric.com 2 Inner insulating material – I prefer to use one layer of Insul-Bright insulated lining and one layer of natural-fibre quilt batting (cotton or bamboo) or towelling. If you can’t find Insul-Bright, use two layers of natural-fibre quilt batting. 3 Double fold bias binding – enough to go around your pot holder + 4 inches for a loop
How many inches to make a pot holder?
While store-bought pot holders can be smaller, I prefer to make my pot holders 10 to 12 inches.
What material do you need for a pot holder?
For a simple pot holder with binding, you need 3 things: Outer fabric made from natural fibres – quilting cotton is a great option. Inner insulating material – I prefer to use one layer of Insul-Bright insulated lining and one layer of natural-fibre quilt batting (cotton or bamboo) or towelling. If you can’t find Insul-Bright, use two layers ...
How big should pot holders be?
While store-bought pot holders can be smaller, I prefer to make my pot holders 10 to 12 inches. This makes it much harder to burn your hand but is still a manageable size. A great scrap-busting project is to piece together fabrics or use a quilt block. For this tutorial, I’ve used a log cabin quilt block.
How to make a quilt block bigger?
Cut your front fabric (or quilt block) to the desired sized. Cut the two layers of insulating material approximately 0.5 inches bigger than the front fabric. Cut the backing fabric another 0.5 inches bigger than the insulating material.
How to keep potholder from shifting?
Lay your backing with right side down, then place 2 layers of the insulating batting ( or cotton batting) on top of that. Then, place the potholder top side with right side up. Fix using safety pins or spray baste the layers together. You can use Odif 505 to do so, for me this is the easiest way to prevent shifting.
What interfacing to use for potholders?
What interfacing To Use for a Potholder. I used two layers of Insul-Bright to make your potholders extra heat-resistant. And to make them thicker. You can use 1 layer of insul-Bright plus a layer of cotton batting. Also, you can use one single layer of thick cotton batting instead. Do not use polyester-based batting for potholders, ...
What is the best size for a potholder?
There are several standard sizes for square potholders, anything ranging between 6" and 10", I currently use 7" and 8" potholders in my kitchen. And here and then, I might borrow the miniature 5" pot holders from my daughter's play kitchen to use them as mug rugs for my morning coffee. If she let's me!
How to make a triangle with a hanging loop?
Pin and sew across the diagonal, catching the hanging loop into the seam. Then fold the sewn square back along the sewn line and press. You get a triangle. Sew a few stiching lines along the edge to secure the hanging loop and add some structure to this bit of fabric. Loop done.
How to cut binding for a quilt?
I cut mine at 2 ½ " from selvedge to selvedge to accommodate for the thickness due to 2 batting layers. You can get away with a slightly narrower binding, 2 ¼" should be fine too.
How many squares do you need for a potholder?
Please bear in mind that in this case, you'll need two diferent 8" squares in contrasting fabric - this will make two four-patch blocks. For the mini potholder, you'll need two 6" squares to make a 5 ½" raw front piece for the mini potholder.
Where do you fold raw edges?
fold the two long raw edges towards the center, then
How to make a potholder not unravel?
If you don’t have a curtain ring, you can also use a bit of fabric glue to seal the knot where you fasten off the last loop. This way, the potholder will not unravel in the wash.
How Do You Finish a Potholder Loom?
Finishing a potholder loom is quite simple, but it can seem daunting to a beginner.
What hook do you use to weave?
A weaving hook (optional but highly recommended): If you don’t have a weaving hook, you can use a crochet hook or even your fingers. However, a weaving hook will be more convenient since its defined rounded hook will make it easier to pull the loops and less likely to snag on your work while weaving.
How many pegs do you need for a potholder loom?
You can use a different sized loom, but make sure to use the appropriate sized loops as well. These looms usually have 18 to 20 pegs on each side.
What is a potholder loom?
A potholder loom is a great tool to introduce you to the art of weaving. This versatile tool is so friendly for beginners, and making potholders using a loom is a fun craft project you can work on even with young kids. The best thing about making potholders using a loom is that you can use recycled materials from old T-shirts or scrap fabric ...
How big of a potholder loom do you need to make a rug?
When making bigger garments, you can create a few squares with a 9” by 9” potholder loom, and sew the squares together to create a rug or blanket.
How many cotton loops are there in a potholder?
About 40 cotton loops that are approximately 7″ in length: If you are making a potholder that will need to handle heat well, make sure that the materials you are using are 100% cotton, since synthetic materials can melt when in contact with high heat.
How to Bind a Potholder?
As we have already told you, making the vest will only require equipment available at your house. If you are the one who is going to wear it, ask your mom to provide you with the necessary items.
Which side should a potholder be layered on?
The regular and potholder top should be layered from the right side up
How to cut out the top of a potholder?
Use scraps to cut out the top of a potholder. In this case, you need to trim the edges from 7.5 square inches. Once you have done that, cut the backing, along with the regular and heat resistant batting. Make sure to keep the measurement in 8 square inches, just we have stated above. If you feel complications while acquiring the accurate measurement, you can simply take the batting and lay the potholder top over it. Then cut with that measurement, you will get the required measurement.
What is a potholder quilt?
A potholder is actually a mini quilt that keeps the pot safe without letting the heat get through it. It is completely heat resistant and can be made easier with the scraps. You can easily get one of them from your nearest shop, but that can be a bit costly. Well, if you are really going to use them for your regular purpose, why don’t you make one by yourself, it won’t going to charge like those items in the market. It is quite easy and can be made easily from the scraps. The only tricky thing is the binding. Don’t worry; I will show you the exact way to get through this problem. So, leave all the rests and as for me how to bind a potholder.
How to make a binding section sharper?
Pull the binding tail gently when you reach the overlap section. If you pull too hard, it will make the binding section sharp. That’s why it is recommended to pull it gently.
