How do I calibrate my Hayward salt generator?
- Turn Salt System Off and On. With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”.
- Average Salt Reading. Wait until the numbers stop changing.
- Assess the Salt Cell Reading.
How to recalibrate Aqua Rite?
Does the Hayward Aqua Rite match the salt level?
Can you recalibrate Hayward Aqua Rite?
How do you calibrate a Hayward?
0:000:59Hayward Aqua Rite Salt Level Calibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what i do is i turn turn it off. Turn it to the minus zero and turn it up so whatever yourMoreSo what i do is i turn turn it off. Turn it to the minus zero and turn it up so whatever your reading is turn to auto.
How do you reset a salt chlorinator?
To reset, move the switch to 'Off' and then back to 'Auto'. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to 'Super Chlorinate' and back to 'Auto'. It takes about 30 seconds for the unit to settle back on the default reading.
What should my Hayward salt chlorinator be set at?
between 2700-3400 ppmThe ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal.
What if my Hayward salt chlorinator reads high salt?
The High Salt LED will be ON when the cell amperage is above the maximum limit. High Salt LED may also be ON if the control is set for the wrong Turbo Cell type. The LCD display will read 'HI'. Verify salt level is 2700-3400ppm and check with independent test to ensure accuracy.
How do I reset my Hayward salt chlorinator?
Reset AquaRite Salt Chlorination Inspect Cell Light If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
How do you recalibrate the salt level on a Hayward Pro Logic?
You must reset the system by entering the 'Diagnostic Menu' and then hitting the right arrow key once and then pushing the plus (+) key once. This should reset the light and message. Lastly, follow the instructions on page 16 to reset the salt level after cleaning the cell.
What percentage should salt cell be set on?
We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it's high you can lower the percentage.
Why is my Hayward salt system not generating chlorine?
Water flow The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
What happens if I put too much salt in my pool?
Bottom Line. A little bit of extra salt in your pool doesn't generally result in any concerning issues. However, putting in excessive amounts of salt, resulting in salt levels 5000 ppm or more, can lead to corrosion of your metal pool equipment. Not to mention, having too much salt will also make the pool saltier.
How do I know if my Hayward salt chlorinator is working?
0:252:22Tip 3 - How to check if your salt cell is working - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp we're looking to see the green lights. Come on as soon as the water is pumping through the systemMoreUp we're looking to see the green lights. Come on as soon as the water is pumping through the system.
Why is my salt cell Reading High?
The “High Salt” light indicates that there is a higher salt level than recommended. The “High Salt” light will stay on for several reasons including: cell amperage is above the maximum limit, the control is set to the wrong turbo cell, or, most commonly, there is too much salt in your pool.
How do you troubleshoot a Hayward salt cell?
1:184:19How To: Troubleshoot a Hayward AquaRite - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe high salt LED is illuminated. Check the salt level with a test kit if the salt level is too highMoreThe high salt LED is illuminated. Check the salt level with a test kit if the salt level is too high lower. It by draining some of the pool water via the pools wastewater.
Why is my salt chlorinator not working?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
How do I know if my salt chlorinator is working?
1:252:22Tip 3 - How to check if your salt cell is working - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat we're doing here and we turn it on is we're looking for bubbles or a fizzing. Effect. Once weMoreWhat we're doing here and we turn it on is we're looking for bubbles or a fizzing. Effect. Once we see the bubbles. And the fizzing. We know that it's actually working.
How do I know if my salt cell is bad?
If the salt cell bubbles, but only a little bit, then you probably have a bad cell. It is still a good idea to call a pool professional to confirm this diagnosis. If the salt cell bubbles vigorously, then it is working fine.
How do I reset my Hayward Swimpure plus salt chlorinator?
1:063:16Reseting Pool Salt Generator - YouTubeYouTubeStart of suggested clipEnd of suggested clipScreen. So you're going to turn the system off. And then you're going to turn the system back on andMoreScreen. So you're going to turn the system off. And then you're going to turn the system back on and then you're going to hit this five times.
How to recalibrate Aqua Rite?from inyopools.com
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. Click Here to View Salt Test Strips.
Does the Hayward Aqua Rite match the salt level?from inyopools.com
WRITTEN BY: Inyo Pools. Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. If the salt cell is clean but the salt reading is off, the Aqua Rite will need to be recalibrated. The following steps will provide a guide on how to recalibrate a Hayward Aqua Rite.
Can you recalibrate Hayward Aqua Rite?from inyopools.com
The Hayward Aqua Rite should now be successfully recalibrated. If the incorrect salt reading continues to be a problem, it may be time to replace the salt cell.
Step 1: Adjusting Salinity (Salt) level
Before the chlorine generator can be calibrated correctly, the salinity—or salt level in the pool water—will need to be at the correct level. For these systems, it should ideally be between 3200-3600 ppm (parts per million). This can be tested using a salt test meter or salt test strips.
Step 2: Locating the Calibration Screen
Once the salinity is adjusted to optimal level, the calibration process can begin. With the pump running and unit set to "Auto" position, press the "Diagnostics" button five times. The screen should display " - 0".
Step 3: Setting the Salinity Level
This step can get tricky and may need to be repeated. While on the calibration screen and with the pool pump still running, push the "Auto" switch down to the "Off" position for two seconds.
More About the Calibration Process
Step 3 takes some practice as it counts down very quickly. For example, if the salinity level in the pool water is 3300 ppm, when the switch is pushed from the "Off" position up to the "Auto" position, after 10 seconds, it will display a set of numbers that start going down immediately. It might start at, say, 4800 (could be higher or lower).
Questions & Answers
Question: My control board shows 3,500, but two independent tests say 2,700 and zero chlorine, and cell tests say it’s good. Which one is correct?
How to reset Hayward salt cell?
To reset your Hayward Salt Cell, position the switch to off and then turn back to Automatic. After that, you will need to be patient for five to ten seconds for the relay to click. During the point when the instant salt level is steady (and the negative indication is actually present), twist the switch to ‘Super Chlorinate and back to Automatic.
How to test salt cell?
The below step-by-step guides to testing your salt cell will help a lot: First, switch off the pump. Detach the salt cell but before you do that make sure you take a picture of the cell to avoid putting it in a reverse position. Clean the salt cell following the laid down procedures if required. Place the dummy cell back into the pipe where ...
How to avoid shock from salt cell?
Immerse the salt cell in the pool water but ensure electrical connections are not wet to avoid shock.
Why is my salt cell not bubbling?
If your salt cell is not bubbling, it might be due to a lack of power , or the cell is not good enough. Any salt cell that bubbles a bit is probably not working properly and needs professional diagnosis. A cell that provides excellent bubbles is working properly.
Is a salt cell not working?
Any salt cell that bubbles a bit is probably not working properly and needs professional diagnosis.
How to recalibrate Aqua Rite?
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. Click Here to View Salt Test Strips.
Does the Hayward Aqua Rite match the salt level?
WRITTEN BY: Inyo Pools. Occasionally the salt level on the Hayward Aqua Rite may not match the actual salt level of the pool. If the salt cell is clean but the salt reading is off, the Aqua Rite will need to be recalibrated. The following steps will provide a guide on how to recalibrate a Hayward Aqua Rite.
Can you recalibrate Hayward Aqua Rite?
The Hayward Aqua Rite should now be successfully recalibrated. If the incorrect salt reading continues to be a problem, it may be time to replace the salt cell.
