How to Calibrate Salt Reading on Hayward AquaRite
- First, make sure your salt cell is clean. ...
- While the pump is running, slide the main switch from "Auto" to "Off," and then switch back to "Auto." ...
- When you hear the click, press the diagnostics button five times to display instant salinity. ...
- The number on the display will start high, and begin to go down. ...
- Your Hayward AquaRite is now calibrated!
How to recalibrate salt level on a Hayward Aqua rite?
How To Recalibrate the Salt Level on a Hayward Aqua Rite Step 1. Before recalibrating, test the water with salt water test strips to determine the correct salt level. Step 2. With the pump running, move the main switch from "Auto" to "Off" and then back to "Auto". Wait for approximately... Step 3. ...
How do I calibrate my aquarite control?
If the salt level displayed on your AquaRite control doesn't match the actual salt levels in your pool, you may need to calibrate your system. Here's how. First, make sure your salt cell is clean. A dirty cell can give a false salinity reading. While the pump is running, slide the main switch from "Auto" to "Off," and then switch back to "Auto."
How much salt should I add to my Hayward aquarite?
Test the water for an accurate salt reading, and add more salt according to your owner's manual recommendation of 2,700–3,400 ppm (parts per million). 3,200 ppm salinity is ideal for Hayward AquaRite salt systems. 5. "High Salt" Light On The only way to lower the salt level is by partially draining and refilling the pool.
How do I recalibrate my saltwater pump?
Before recalibrating, test the water with salt water test strips to determine the correct salt level. If the results from your test strip are not the same as the Aqua Rite, proceed to step 2. With the pump running, move the main switch from "Auto" to "Off" and then back to "Auto". Wait for approximately 10 - 15 seconds for a click inside the panel.
How do you recalibrate Aqua Rite salt Cell?
1:022:17Recalibrating an Aquarite Salt Chlorine Generator - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst step slide the main switch to the auto. Position. Second step push the diagnostic button untilMoreFirst step slide the main switch to the auto. Position. Second step push the diagnostic button until a T number appears on the display.
How do you reset the salt level on Aqua Rite?
To reset, move the switch to 'Off' and then back to 'Auto'. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to 'Super Chlorinate' and back to 'Auto'. It takes about 30 seconds for the unit to settle back on the default reading.
How do you calibrate a Hayward AquaRite salt cell?
Press the diagnostic button 8 times to get to the cell type menu. Flip the switch back and forth between "Super Chlorinate" and "Auto" until you see the correct T-Cell number displayed, and return the switch back to "Auto." Your Hayward AquaRite control unit is now calibrated for use with your new salt cell!
How do I reset my Hayward Aqua plus salt?
Turn the filter pump on. You must reset the system by entering the 'Diagnostic Menu' and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.
What if my Hayward salt chlorinator reads high salt?
The “High Salt” light indicates that there is a higher salt level than recommended. The “High Salt” light will stay on for several reasons including: cell amperage is above the maximum limit, the control is set to the wrong turbo cell, or, most commonly, there is too much salt in your pool.
What should my Hayward salt chlorinator be set at?
2700 ppm to 3400 ppmSalt Systems work best with approximately 3200 parts per million (ppm) of salt, which is roughly the equivalent to a teaspoon of salt per gallon. However, all Hayward Salt Systems are designed to operate with salt levels anywhere from 2700 ppm to 3400 ppm.
How do you calibrate a Hayward salt tester?
1:094:46Pocket Pro Salinity Tester #9531600 by Hach® - YouTubeYouTubeStart of suggested clipEnd of suggested clipYeah we're going to put the unit calibration mode by hitting this center button here. You see thatMoreYeah we're going to put the unit calibration mode by hitting this center button here. You see that little arrow on the far left hand and leads us in calibration mode.
Why is my instant salt reading 0?
If the level is above 4000ppm it will not make chlorine it will automatically stop the chlorine production and you will get a zero reading for the salt level.
How do I know if my Hayward salt cell is working?
The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.
What should salt level be in pool?
between 2700-3400 ppmThe ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. Before adding salt to your pool, test the water to check your salt level. If the level is low, determine the number of gallons in the pool and add salt according to the chart below.
Why is my check salt light flashing?
When both the “Check Salt” and “Inspect Cell” lights flash together, it is most likely an indicator that your salt level is below 2700 ppm. Keep in mind, your ideal salt level should be between 2800 ppm – 3200 ppm (parts per million).
How do you calibrate a Hayward Goldline salt system?
0:001:00Hayward Aqua Rite Salt Level Calibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you have to do it quick you go up to super chlorinate and then down auto again right whereMoreAnd then you have to do it quick you go up to super chlorinate and then down auto again right where approximately where it's at so we'll say 35 we want it approximately. So up down and just leave it.
How do I reset my Pentair salt cell?
Press the "More" button to cycle through each salt level, and then press the "Less" button to choose and save the display as the new salt level. The "PWR", "Cell", "Life", and "Flow" lights will flash 4 times, then the mode exits to normal.
Why is my instant salt reading 0?
If the level is above 4000ppm it will not make chlorine it will automatically stop the chlorine production and you will get a zero reading for the salt level.
How do I lower the salt level in my pool?
The only way to lower the salt concentration of your swimming pool's water is to dilute it. Unfortunately, this means you will need to partially drain your pool and refill it with fresh water. This is true because salt doesn't wear out, break down or evaporate; only your water will evaporate.
Why is my salt cell not reading correctly?
Be sure that the pump is running and the turbo cell is clean (buildup of calcium or debris in the cell can cause erroneous salt readings) and that the salt level in your pool water in within the recommended range of 2700 to 3400ppm. A salt level of 3200ppm is considered ideal.
Step 1: Adjusting Salinity (Salt) level
Before the chlorine generator can be calibrated correctly, the salinity—or salt level in the pool water—will need to be at the correct level. For these systems, it should ideally be between 3200-3600 ppm (parts per million). This can be tested using a salt test meter or salt test strips.
Step 2: Locating the Calibration Screen
Once the salinity is adjusted to optimal level, the calibration process can begin. With the pump running and unit set to "Auto" position, press the "Diagnostics" button five times. The screen should display " - 0".
Step 3: Setting the Salinity Level
This step can get tricky and may need to be repeated. While on the calibration screen and with the pool pump still running, push the "Auto" switch down to the "Off" position for two seconds.
More About the Calibration Process
Step 3 takes some practice as it counts down very quickly. For example, if the salinity level in the pool water is 3300 ppm, when the switch is pushed from the "Off" position up to the "Auto" position, after 10 seconds, it will display a set of numbers that start going down immediately. It might start at, say, 4800 (could be higher or lower).
Questions & Answers
Question: My control board shows 3,500, but two independent tests say 2,700 and zero chlorine, and cell tests say it’s good. Which one is correct?
How to test salt water in Aqua Rite?
Step One: Test the Water. The first thing is to test the water using a saltwater test strip to know the correct salt level. If you get a different reading from the one on your Aqua Rite, move to the next step. Step Two: Switch the Main Switch.
What is the salt level in an inspection cell?
The Inspect Cell and Check Salt LED – They flash together when the salt level is 2500-2600 ppm. Your system should continue to produce chlorine and work properly.
Why Does Salt Chlorinator Fail?
Your salt chlorinator can fail due to several reasons, the main one being lack of maintenance . When you maintain your system, you ensure that excess calcium does not get stuck on the plates and give a false reading.
How long does it take to hear a click on a pump?
While the pump is operating, move the switch from the “AUTO” to the “OFF” position and back to the “AUTO” position. Wait for about 15 seconds to hear a click in the panel.
Does Hayward Aqua Rite read the correct figure?
Your Hayward Aqua Rite should read the correct figure. If the issue continues, you might need to replace the salt cell.
What does 0 mean in salinity?
OTOH, the -0 instant salinity reading from the so-called new cell signifies that it is in not conducting as in completely dead! Not sure why Leslies claimed it passed the test. Forget about the recalibration, it does nothing at all but satisfies yourself! You can reference the above diagnostic readings to support your warranty claim.
How long does it take for a pool to turn solid after unplugged?
Correct! If the cell is unplugged, the check salt and inspect cell indicators should turn solid in about 50 secs after you hear the click. The same is true if the salt level falls below the minimum threshold of 2300ppm. I doubt you have zero salt in your pool. I think you should get a reliable salt test kit like the Taylor K-1766.
What does 32VDC mean on a mainboard?
The presence of 32vdc at the cell jack confirms that your mainboard is operational. However, the so-called new cell when plugged in is not returning feedback to the controller. Try to connect the old cell, press the diagnostic button within 50 secs after you hear the click and post all the numbers.
Does recalibration work with new cell?
As before, the recalibration did not work with the new cell.
How Does the Aqua Rite Salt System Work?
The Aqua Rite salt system is an easy-to-use salt electrolyzer. It works with Hayward’s TurboCell® technology, which ensures reliable and effective salt treatment. It allows to effectively treat the pool water through saltwater electrolysis.
Why Is My Salt Chlorinator Failing?
Your Aqua Rite chlorinator can produce different results because of so many reasons. One of these is the lack of regular maintenance.
Start By Inspecting the System
Incorrect Aqua Rite readings can occur because of many reasons. Therefore, you have to inspect the system in the following way:
How to Calibrate Aqua Rite System
The steps required for recalibrating the Aqua Rite salt system to ensure accurate reading once again are explained below:
The Problem Is Best Resolved With Maintenance and Calibration
The Hayward Aqua Rite salt chlorinator is designed to read accurate figures. If otherwise, you can reset the Aqua Rite salt system by recalibrating it.