Remove lawn mower belt:
- 1. Remove the right belt cover.
- 2. Remove the left belt cover.
- 3. Open the access cover.
- 4. Remove the belt finger from the PTO idler arm.
- 5. While wearing safety goggles, disconnect the PTO belt idler spring from the anchor bolt with a spring puller or similar tool.
- 6. Remove the PTO belt from the deck pulleys.
What size of belt goes on Gravely zero turn mower?
Gravely Lawn Tractor Mower Drive Belt 47-11/32 X 17/32.
Do you have to remove mower deck to replace belt?
To replace this belt, the deck should be off the lawn mower. You'll crawl underneath and locate the idler pulley(s) and loosen the cap screw at the center of the pulley to allow a wiggling movement in the pulley.
How do you change a lawn mower belt?
1:013:06Replacing the Drive Belt on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipRelease the height adjuster lever and pull the drive cover. Off pull off the belt keeper from theMoreRelease the height adjuster lever and pull the drive cover. Off pull off the belt keeper from the top of the transmission. Release the drive belt from the transmission pulley. And remove it push.
How do you change a belt?
1:192:22How to Replace a Serpentine Belt in Your Car (Fan Belt) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just hook it up here to the bolt that loosens attention her pulley and then pull on it. As youMoreYou just hook it up here to the bolt that loosens attention her pulley and then pull on it. As you pull it down the belt gets loose. Then you can just take it off. And out comes the old fan belt.
How long does it take to change a mower belt?
about 1.5 hoursReplacing a mower belt is easy and doesn't take too much time, even for those who don't have much, if any, mechanical experience. All it takes are a few wrenches, and about 1.5 hours on a Saturday morning.
How often does a mower belt need to be replaced?
There is no specific time length that mower belts need to be replaced. Some belts may last longer than others due to different operating conditions. One thing is for certain though, the more the mower is used, the sooner you will need to consider replacing the mower belt.
How do you remove a mower deck belt?
1:043:46How to Replace a Deck Belt on a Lawn Tractor Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd disengage the mower engagement lever lower the attachment lift lever to its lowest. PositionMoreAnd disengage the mower engagement lever lower the attachment lift lever to its lowest. Position clean all loose debris from the belt and deck area most tractors have a decal located on the deck.
What are the two belts on a riding lawn mower?
Riding mowers will often have V-belts from the engine to the transmission. Riding mowers will often have V-belts from the engine to the transmission, allowing the operator to vary blade speed, or mower speed. Most often the two are co-dependent on a single belt and transmission.
How do I know if I need a new mower belt?
1:473:07When Does a Mower Belt Need Replaced? From Moe's ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it looks like it's derailed off of a pulley. At some point and it's got like a groove down theMoreAnd it looks like it's derailed off of a pulley. At some point and it's got like a groove down the center of it. And if you look up at look at it up close you can kind of see that. It's it's pretty
Can I replace engine belt myself?
Automatic belt tensioners, standard in most cars now, make changing a serpentine belt a simple DIY repair. Follow the clear photos and step-by-step instructions and you'll be done in 15 minutes.
How long does it take to change a belt?
How long it takes to replace a drive belt depends on your skill, but the average time is about one hour. A very skilled technician could perform a drive belt replacement in less than 30 minutes.
What tools do I need to replace belt?
Tools/Supplies Needed:ratchet and socket set.torque wrench.new replacement belt.new tensioner.new pulley.wrench set.jack and axle stands or ramps.
Is there a difference between a deck belt and a drive belt?
The "Deck Belt" goes around the pulleys right above the blades on the deck and then to a double pulley. The "Drive Belt" on your mower goes from the transmission, around an Idler pulley then over to the double pulley I mentioned before. The Drive belt also plays a role in making the wheels turn.
Is a deck belt and drive belt the same?
The deck belt is the one that powers the blades and the drive belt powers the tractor's motion. The deck belt comes with the deck when you remove the deck but the drive belt remains with the tractor.
How do you change a drive belt on a riding lawn mower?
1:504:42Replacing a Ground Drive Belt on a Riding Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe drive belt from the transaxle pulley pull out the ground drive belt loop the ground drive beltMoreThe drive belt from the transaxle pulley pull out the ground drive belt loop the ground drive belt over the transaxle pulley. Position the battery box in the opening.
How do you put a deck belt back on?
1:313:00How to Change the Deck Belt on a Cub Cadet Riding Lawn ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the belt covers back on the outer pulleys. Slide the cutting deck back under the mower rout theMorePut the belt covers back on the outer pulleys. Slide the cutting deck back under the mower rout the deck belt around the engine pulley and secure the belt keeper.
When to replace a Gravely mower belt?
When to replace a mower belt. Gravely ® suggests replacing a hydrostatic drive belt as soon as it shows signs of wear. Though the recommendations outlined in Gravely operator's manuals suggest a belt will last for a good portion of the mowing season, taking an extra minute or two each day to ensure the belt is without cracks, burns or damage, ...
How to install hydro drive belt?
1. Feed the hydro drive belt from above the transaxle and toward the unit interior from either the left or right side of the unit. Engage the belt around the transaxle pulley on whichever side the belt was fed into. 2.
What is a hydro belt?
Hydro belts, transaxle drive belts, hydrostatic drive belts and ground drive belts. Different terminology, same thing. Whatever you call it, its function is to transfer power from the engine to the transaxles, powering the drive wheels on a zero turn lawn mower.
How to tell if lawn mower belt is worn?
Mower belt edges should be smooth and even throughout the entire length of the belt. If even a small portion of the belt is worn, it's at risk of breaking and should be replaced .
What happens if a belt is cracked?
If it appears shiny, glazed or burned, it will need to be replaced. The belt is cracked. If the belt appears brittle and is deteriorating to the point that it has cracks, even shallow cracks, it's at high risk of breaking and needs to be replaced.
Can Gravely repair your lawn mower?
Gravely dealers are your best resource for service help, but immediate service isn't guaranteed during the busy season. If you work with a dealer who doesn't always have capacity to repair your machine at a moment's notice, consider learning simple procedures, like belt replacements, yourself. Gravely commercial lawn mowers are designed so most people can complete light service tasks like belt replacements on their own and without special tools.
Can Gravely OEM belts be wiped out?
No matter how healthy the supply of Gravely OEM belts is at our distribution centers, a dealer could be wiped out of their inventory on any given day during the busy season. Don't put yourself at the mercy of a dealer's supply. Stock up on belts early and keep extras on hand. Breaking a belt in the field is enough of a challenge, but not having a replacement belt to get a mower back in business will turn a couple hours of downtime into a couple days of downtime.
What is a PTO belt?
The PTO belt is an extremely important part of the mower. It is the belt that gives power to the blades to the engine to make them spin. A damaged or worn belt means your blades won’t spin properly and your grass won’t get cut as nicely as it should. Luckily, replacing the PTO belt is easy! Here’s How!
Where to pull idler arm?
Pull the idler arm towards the outside of unit until PTO belt can be routed around the left mower deck pulley
What to do before servicing a Jack's Power?
Jack’s Safety Tips: Before servicing or repairing any power equipment, disconnect the spark plug and battery cables. Remember to wear appropriate safety glasses and gloves to protect against harmful chemicals and debris. View our Disclaimer.
What happens when a transaxle belt breaks?
When a transaxle drive belt breaks, the drive wheels of the lawn mower stop turning, leaving the lawnmower stranded wherever it sits, even if it's in the middle of your yard.
How to install hydro belt?
Hydro belt installation: 1. Install the transaxle drive belt and route around the engine pulley, transaxle pulleys and idler pulleys as shown in the belt routing diagram in the operator's manual. 2. Reinstall the clutch stop bracket onto the clutch stop and secure to the transaxle brace.
How does a belt turn when an engine is running?
When the engine is running, the belt is turned by the engine pulley and the belt then turns the transaxle pulleys , supplying power to the transaxles and allowing them to drive the wheels when the steering levers are moved by the operator.
What is a transaxle belt?
What's a transaxle belt? Transaxle drive belts, hydro belts, transmission belts, hydrostatic belts, and pump belts are varying terminology for the same belt that powers the transaxles of a zero turn lawn mower. Without getting too far into the technical weeds, transaxles are the motors that operate the drive wheels of a zero turn lawn mower.
How does a zero turn lawn mower work?
When the steering levers are pushed forward on a zero turn lawn mower, the shafts on the transaxles turn the wheels forward. It's as simple as that. The Hydro-Gear ® transaxles on an Ariens ® zero turn lawn mower are not directly driven by the lawn mower engine itself, but by a belt. The transaxle drive belt is routed through an engine pulley, ...
How to remove hydro belt?
Hydro belt removal: 1. Remove the left belt cover from the deck and gently pull the PTO belt out of the left spindle pulley. 2. Disengage the PTO belt from the clutch. 3. With a pliers, hold the hooked end of the tensioner bolt located under the gas tank while loosening the nut on the other end of the bolt.
What happens if a mower belt is worn?
Mower belt edges should be smooth and even throughout the entire length of the belt. If even a small portion of the belt is worn, it's at risk of breaking and should be replaced. 2. The belt has a glazed or burned sidewall. Look at the belt edge that contacts the pulleys.
