Lay the guide bar on a flat surface. Install the new chain onto the guide bar; ensuring that the sharp side of the teeth (along the bottom of the chain) are facing the saw. Partially install the bar and chain assembly onto the saw, ensuring that the chain engages the drive sprocket on the clutch drum.
How do you remove the chain from a chainsaw chain?
Remove the clutch cover assembly. Remove the (2) nuts from the bar mounting bolts. Rotate the chain tensioner screw counterclockwise to release tension from the chain. Remove the clutch cover assembly. 2. Remove the chain. Remove the bar and chain assembly from the saw. Remove the chain from the guide bar.
How do I adjust the chain tension on my Chainsaw?
Using a long screwdriver, rotate the tensioner screw (in either direction) until the bar adjustment pin engages the hole on the bar. (The entire assembly should snap into place when this occurs). Once the adjustment pin engages the bar; rotate the tensioner screw in the opposite direction until the chain begins to tension.
How do you install a chain on a lawn mower?
Install the chain. Lay the guide bar on a flat surface. Install the new chain onto the guide bar; ensuring that the sharp side of the teeth (along the bottom of the chain) are facing the saw. Partially install the bar and chain assembly onto the saw, ensuring that the chain engages the drive sprocket on the clutch drum.
How do you replace a chain on a craftsman chainsaw?
Grasp and raise the distant end of the bar and chain assembly (opposite the engine) until the saw begins to rise. While holding the bar in the raised position, grasp the chain at the center (and top) of the bar. Lift the chain away from the bar assembly and inspect the gap between the two components.
How do you put a chain back on a Poulan electric chainsaw?
0:553:56How to Install a Chain on a Poulan Chainsaw : Lawn Care & Power ToolsYouTubeStart of suggested clipEnd of suggested clipSo the sharp edge is pointing back on the bottom of the bar. With a pointed the right direction I'llMoreSo the sharp edge is pointing back on the bottom of the bar. With a pointed the right direction I'll go ahead and wrap the cane around this rear sprocket into the groove on the bar.
How do you change the chain on a Poulan 14 inch electric chainsaw?
1:454:57Chainsaw Repair - Replacing the Chain (Poulan Part # 581562101)YouTubeStart of suggested clipEnd of suggested clipI'll remove the side cover by removing the two nuts and loosening the tension. Screw. With theMoreI'll remove the side cover by removing the two nuts and loosening the tension. Screw. With the clutch cover removed. Now I can remove the bar on the chain. Now installed the bar in the cane on.
What size of chain is a Poulan electric chainsaw?
050 Gauge 3/8 Pitch.
How do you loosen the chain on a Poulan chainsaw?
0:031:39HOW TO Adjust The Chain on Your Poulan Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd a half inch socket wrench first of all you want to loosen these two nuts with your half-inchMoreAnd a half inch socket wrench first of all you want to loosen these two nuts with your half-inch socket wrench and then this will be the adjusting screw right there. You don't want to take the nut.
What kind of oil do you use in a Poulan electric chainsaw?
Ideal Oil. Poulan encourages customers to use its own brand of 2-cycle oil for air-cooled engines, most commonly found in 3.2 ounce size. Poulan brand oil is was designed specifically for its chainsaws and thus it is the only oil the brand guarantees.
How do you put a chain back on a chainsaw?
0:321:58HOW TO PUT ON A CHAIN SAW CHAIN THE RIGHT WAY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo make sure your chain is facing the right way so put it on the chain. Bar. These teeth the pointyMoreSo make sure your chain is facing the right way so put it on the chain. Bar. These teeth the pointy bit is facing forwards. So I wrap the chain around the back. There.
Does an 18 inch chain fit an 18 inch bar?
General chain lengths, like 18 inches, are not interchangeable. That's because chainsaw chains actually have three measurements: number of drive links, pitch, and gauge.
What does S62 mean on a chainsaw chain?
The Oregon S62 is designed to fit all chainsaw brands, with models that require a 3/8 Inch pitch, .050 Inch (1.3 mm) gauge, with 62 drive links. Fits chainsaw models from several brands including Husqvarna, Echo, Poulan, Craftsman and more.
Will a Stihl chain fit a Poulan saw?
Product Description. STIHL 63 PM3-56 chainsaw chain made in Switzerland with high quality steel. This chain fits Homelite, Poulan, Echo, Craftsman, Remington and others with the same specs.
How do you tighten a Poulan chain?
Loosen the guide bar nuts and turn the adjusting screw counter-clockwise 1/4 turn to loosen the chain if it is too tight. Loosen the guide bar nuts and turn the adjusting screw clockwise 1/4 turn to tighten the chain if it is loose. Tighten the guide bar nuts firmly with the guide bar adjusting wrench or socket wrench.
How do you adjust a Poulan chainsaw?
3:477:40HOW TO ADJUST POULAN CHAINSAW CARBURETORYouTubeStart of suggested clipEnd of suggested clipSo when that happens usually the case is that you got a screw in the low screw which is the leftMoreSo when that happens usually the case is that you got a screw in the low screw which is the left screw. I'm going to turn it in half a turn half a turn and then I'll proceed start it again.
How tight should a chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can't pull the drive links out of the bar nose.
How do you tighten the chain on a Poulan peak chainsaw?
2:193:33Poulan pln 1514 electric chainsaw adjustment. pln1514 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it's two phillips head screws to tighten it back in they're long guys like this tighten it back.MoreAnd it's two phillips head screws to tighten it back in they're long guys like this tighten it back. And that's how you tighten the bar and chain on adjust the bar and chain on this electric.
Are chainsaw chains universal?
No, chainsaw blades are not universal, not every bar and chain will fit on your machine. Chainsaw chains need to have the correct specification to fit on your bar. If you have a chain that is too long or too narrow it will not fit. Mixing brands of chains is no problem as long as they are compatible.
How do you sharpen a chainsaw chain?
3:1820:36No Nonsense Guide to Chainsaw Sharpening. How To ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI hold both ends of the file. And give it a good firm. Stroke now i am pushing. It kind of into theMoreI hold both ends of the file. And give it a good firm. Stroke now i am pushing. It kind of into the tooth. So that i'm getting both that top edge. And the side edge this top edge here.
How do you start a Poulan Pro chainsaw?
6:127:44Poulan Pro - Chainsaw Operation - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bulb need not be completely filled pull the starter handle with your right hand and pull out theMoreThe bulb need not be completely filled pull the starter handle with your right hand and pull out the starter cord slowly. Until you feel resistance.
How to align drive links on a new chain?
Pull the bar assembly forward (away from the engine) to align the drive links (on the new chain) with the groove in the bar.
When is a chain tensioned correctly?
The chain is tensioned correctly when the weight of the chain does not cause it to sag below the guide bar.
How to raise a saw bar?
Grasp and raise the distant end of the bar and chain assembly (opposite the engine) until the saw begins to rise.
How to tell if a chain saw blade is dull?
As the blade becomes dull, you will notice that the saw doesn't cut as fast. You will see the sawdust change from thin shavings to a powdery dust. Often, you will notice smoke coming from the bar and chain while cutting.
What is a chainsaw?
Chainsaws are amazing tools. There is nothing quite like them for making quick work of removing a tree in your yard, pruning branches, or cutting firewood for the winter. When you think about how fast a chainsaw cuts, and the abuse the chain takes, it's amazing that the chain stays sharp as long as it does.
What happens when a chain is run with too little tension?
If a chain is run with too little tension, it may come free from the bar. This is a dangerous situation, and it usually leads to a damaged chain. When the chain leaves the bar, it often damages the driver links. Those are the spurs on the inside of the chain (which fit into the bar). Inspect the driver links for burrs.
Can you cut down a tree with a chain?
Often, you will notice smoke coming from the bar and chain while cutting. A single chain can easily cut down an entire tree (or more), as long as the wood is clean and debris free. A single stone, nail (or the like) will almost immediately dull a chain (if struck).
What are the main parts of a chainsaw?
The main chainsaw parts are involved in a guide bar, engine, and sprocket. As a chain becomes twisted and dull, it radically decreases the productivity of the machine. As you most likely know, chainsaws work at high RPMs, and these chain related issues can affect the safety of operation and cause lethal injury.
Where is the tensioning screw on a chain?
The next thing is to find the tensioning screw. It is usually found inside the guide bar. When you discover it, loosen it with your flat head screwdriver a little so that the new chain will slip on easier.
Do You Need To Replace Your Chainsaw Chain?
The main chainsaw parts are involved in a guide bar, engine, and sprocket. As a chain becomes twisted and dull, it radically decreases the productivity of the machine. As you most likely know, chainsaws work at high RPMs, and these chain related issues can affect the safety of operation and cause lethal injury. For instance, kickback is considered to be the number one cause of chainsaw related injuries.