Replacing Inground Swimming Pool Lights
- 1. Disconnect Electricity to Pool Turn the circuit breaker off to the swimming pool light. ...
- 2. Remove Screw Holding Light Housing Look for the single screw along the bottom of the pool light housing bezel. ...
- 3. Remove the Light Housing ...
- 4. Loosen Other Screws ...
- 5. Replace All Corroded Screws ...
- 6. Remove Original Bulb ...
- 7. Install the Replacement Bulb ...
- 8. Replace Pool Light Housing ...
How do you change the bulb in a pool light?
What Are The Steps Involved?
- Safety First! Turn Off the Power. ...
- Remove the Top Screw from the Light. Usually, there is only one screw holding the light fixture to the wall of your pool. ...
- Pry the Light Fixture Out. When the screw is out, put it in a pocket or baggy to make sure you don’t lose it. ...
- Test the Wiring. More safety precautions! ...
- Take the Fixture Apart. ...
- Remove the Old Light Bulb. ...
How to change an inground pool light fixture?
Part 3 Part 3 of 3: Reinstalling the Pool Light Fixture
- Replace the lens and reassemble the fixture. Place the gasket and the lens back in place covering the bulb.
- Replace all screws and lock in all tabs to close the light fixture. You’ll simply reverse the disassembling process to re-assemble the pool light fixture.
- Place the fixture back into light niche and screw in the top screw. ...
How many people are needed to change a light bulb?
If the bulbs are wholly or partially with in a distance where 1 person can change 2 light bulbs you would start at a minimum of 5 people and add more as needed until you had max of 1 person per light bulb or 9 people total.
Does it take to change a light bulb?
None. The light bulb has to want to change. 2. How many Mexicans does it take to change a lightbulb? Just Juan. 3. How many guys in the friendzone does it take to change a lightbulb? None, they just stand around complimenting it then get pissed when it doesn’t screw.
Why is my light bulb dimming?
What to do if light fixture is leaking?
What is the screw that holds a pool light?
How to remove a pool light?
How long to bleach LED lights?
How many testimonials does wikihow have?
How to test if pool light works?
See 4 more
About this website
How do I change the light bulb in my inground pool?
Safety always being the number one priority, be sure to read all the instructions before you begin, and don't skip any steps.Turn Off the Power. ... Remove the Pilot Screw from the Light. ... Pry out the Fixture. ... Test the Wiring. ... Take the Fixture Apart. ... Remove the Old Light Bulb. ... Add the New Light Bulb. ... Test the Light.More items...•
Do you have to drain pool to change light bulb?
Fortunately, the answer is no—the water typically does not need to be drained! Because the electrical cable is sealed, it's impervious to any water that will get into the conduit when the bulb is being replaced.
How do I change my pool light without draining?
There is no need to lower the water level in your pool to replace the burned-out bulb. Instead, you can remove the light housing from the side of the pool, pull the fixture up onto the side of the pool, and change the light bulb there.
How much does it cost to replace an inground pool light?
The average pool light replacement cost $625. Pool light repairs prices are a lot more budget friendly at $65 to $150 each. Simply replacing the bulbs is $20 to $100 for each one subject to type and function.
What happens if water gets into pool light?
If you are swimming with goggles, it's good to check your pool lights for leakage. Engineers design the light fixture to stay dry, and water in the housing means the bulb could blow at any moment. If you see a water line in your light, it means you have a warped or broken lens gasket, and it's time to get to work!
Do electricians change pool lights?
Make sure that you work with a qualified electrician who can handle all your swimming pool lighting needs. Our team of level 2 electricians in the Northern Beaches perform every task with safety at the forefront, especially when it comes to your pool. Such services include: Pool lighting installation.
Can pool lights be changed underwater?
And, like any light, the bulb can burn out and need replacing. Thankfully, pool lights are designed to be replaced without having to lower the water level of the pool. Simply detach the light's outer casing from the side of the pool, pull it out of the water onto the pool's edge and replace the bulb from there.
How often should a pool light be replaced?
Your pool lighting should give you few problems overall. Most incandescent bulbs will burn for 1,000 hours before bulb replacement is necessary. LED bulbs can burn for 25 years or more (or so they tell us).
How do I know if my pool light bulb is bad?
1:594:47How to fault test a pool light fixture - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's with me touching it so it changes resistance even just by me touching it right. So you testMoreThere's with me touching it so it changes resistance even just by me touching it right. So you test either of the two you test the black one the ground. You test the white one the ground.
Can you fix a pool light without draining the pool?
Replacing pool lights for your in-ground swimming pool does not require draining the water from the pool or hiring a professional. The design of the pool light's housing allows you to remove it from the pool without the need to disconnect any wiring.
Can I replace my old pool light with LED?
Replacing old halogen pool lighting with LED lights is much easier than you think! Their bright, glowing colours create an impressive underwater light show and you can change up the colors to fit the mood with a single click on the remote!
Do pool lights go out?
Obviously, there could be a number of reasons for your pool lights to not be working such as a burned out pool light bulb, water inside the fixture, bad GFCI (ground fault circuit interrupter) just to name a few. All of these issues should be inspected and diagnosed by a qualified repair technician.
Can you fix a pool light without draining the pool?
Replacing pool lights for your in-ground swimming pool does not require draining the water from the pool or hiring a professional. The design of the pool light's housing allows you to remove it from the pool without the need to disconnect any wiring.
How do you change a light fixture in a pool?
2:175:36How To: Replace a Pool Light Fixture - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull a light fixture out of the niche. You should have enough excess cable to be able to lay theMorePull a light fixture out of the niche. You should have enough excess cable to be able to lay the light fixture on the pool deck. Note how the excess cable is stored in the niche.
Do pool lights get water in them?
Water inside the Pool Light? If there is water inside the lens of the pool light, which you can usually see from on-deck, that doesn't mean that the light is leaking, but it does mean that the lamp gasket has failed, letting water leak inside and surround the bulb.
How do I change the bulb in my above ground pool?
0:385:47Changing the Light Bulb in an Above Ground Pool | AqualuminatorYouTubeStart of suggested clipEnd of suggested clipAnd it's actually quite simple what we're going to do is we're going to remove the cap. And we justMoreAnd it's actually quite simple what we're going to do is we're going to remove the cap. And we just basically have to lift up and kind of twist. And then you'll see some wires here.
How to Change a Pool Light Bulb: 11 Idiot Proof Steps
Uh-oh! Your pool light burnt out. Guess you’ll just have to swim on down to replace it… If only knowing how to change a pool light were that easy, right?
How to remove old gasket from pool lens?
Take care when disassembling these pieces and make sure not to drop anything in the pool. Grab a damp rag to remove any old gasket residue from the surface of the lens.
How to check if pool breaker is turned off?
Grab your voltage tester (multimeter) before touching the wires with your hands and test to make sure there’s no electricity running through there. If you’re multimeter registers anything, that means something hasn’t been turned off. Double-check your that your pool breaker is turned off before going on to the next step.
How to know what light bulb to use for pool?
Here, wattage and voltage are especially important. To work out which light bulb model you need, you can pull out your pool user manual to find out the exact type of bulb the fixture requires. Make sure that the new one you buy matches the size, brand, and serial number.
How to loosen a cord on a light fixture?
If the cord doesn’t unravel easily, grab the cord closer to the wall and try giving it a few gentle tugs to loosen it. (Note how the excess cord is stored so you can replace it the same way when you’re reinstalling the light later on.)
How to turn off the power to a pool?
The first (and most important step) is to turn off all power to your pool. Most commonly you’ll have a switch in your home’s circuit breaker box labeled “pool”. Switch this to the off position and then try to turn on the pool lights to make sure there is no power.
How long does it take for a pool light to burn out?
Just a quick peek to make sure the new bulb works and then turn the electricity right back off. If you leave the light on for more than 5 seconds , there’s a chance the bulb will burn out. Normally in the pool, these halogen bulbs have the water to cool them off. So without the water, they get extremely hot.
What to do if you don't see the switch in your pool?
If you don’t see the right switch in the main electrical box, have a look around your pool equipment to find the right box. Once you’ve checked that the power is off and no electricity is running to the pool… check it six more times. Getting electrocuted is not part of the process.
How to ensure power is off?
To ensure the power is off by turning the light switch to on or using a circuit tester. *Caution: For your safety, take all necessary precautions before working with electricity and water. If you are unsure how to work with electricity, do not attempt. Call a electrician or pool service professional. 2.
What is broken clamp?
Clamps are broken to secure fixture back into place. Where do I purchase clips?
Can you put a light bulb back in the water?
Once you change out the bulb and reseal the fixture using a new gasket you should be good to go to put light housing back into the water and reattach into the niche.
Can you change a pool light bulb?
When it comes to changing out your pool or spa light bulb its not quite as easy as just replacing a bulb in a lamp at home. There's some care to be taken here, and with our step by step how to change a pool light guide below, you should be good to go!
Can you upgrade pool lights to LED?
The only thing left to do is enjoy the illuminated paradise you've created with your new pool lights! Wheather you're upgrading to energy efficient LED bulbs or adding flair with new color changing lights the work of changing out the bulbs is sure to be well worth the work!
How much does a halogen light fixture cost?
After mark-up and labor a traditional halogen white light fixture is about $500 (LED lights are MUCH more expensive). There’s a big difference between $500 and $150! It’s not fair to the customer to have to pay $500 for a burnt-out bulb yet it’s bad business to constantly be warrantying lights with new fixtures.
How much does a pool light bulb cost?
A pool light bulb retails for about $30-40. A new pool light gasket for the fixture is about $25. Labor for the repair would be $100-150. Profit on a successful job would be about $120. The cost of a new fixture is about $200 (wholesale). So for every five bulb replacements I would make $600 and then have to eat $200 plus my call-back labor on the light fixture that leaked. So, that’s six times I’ve visited a pool and I’ve netted $400 in addition/ minus the extra warranty labor. All told that’s about $50 profit per job which just isn’t enough income to make light bulb replacement worth while : (.
Can a pool light bulb be replaced?
Its a tough situation but because pool light fixtures leak so often most pool service companies wont perform pool light bulb replacement.
How much does it cost to replace a pool light bulb?
As a general rule, you should purchase a new lens gasket whenever you need to swap out a pool’s light bulb. They’re pretty cheap, about $10 to $20, and they will greatly increase the safety of the new bulb.
How many screws are in a light fixture?
There is usually only one screw, and you’ll probably find it at the top-center portion of the fixture. It’s super easy to loose the screw. Use a magnetic screwdriver if you have one handy.
Can you hire someone to change pool light bulbs?
You can always hire someone else to do the job . However, many pool services don’t offer the option to hire them to change your pool lightbulbs. It ultimately isn’t very profitable because of how common it is for pool light fixtures to leak. If the company warranties their work, changes the bulb and fixture, and it fails a month later, it will eat away almost all of the profit.
How many screws are in a pool light?
Your swimming pool light fixture may have six to eight brass screws holding the lens and gasket to the housing if it is an older model. Check for any corrosion on the screws, and take precautions, so you do not break the screws if corroded. Check with your pool supply center for proper replacement screws if yours appear corroded.
How to turn off pool light?
1. Turn off the circuit breaker for the pool area lighting. Hold a noncontact voltage sensor next to the light switch that supplies power to your swimming pool light. Test the switch in the on and off positions. If electrical voltage is still present, the sensor reacts with both an audible and visual alarm.
How long does a pool light bulb last?
A pool light bulb should last around 1,000 hours, and its housing can last for decades. There are several options when it comes to replacing your swimming pool light bulb, but you must find one that fits the socket and housing. Take your original bulb and gasket to your pool supply center when purchasing replacements.
Who is Cecilia Harsch?
Cecilia Harsch has been writing professionally since 2009. She writes mainly home improvement, health and travel articles for various online publications. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.
Is a pool light necessary?
Home Improvement. By Cecilia Harsch. A swimming pool light isn’t necessary but adds to the aesthetics of your pool at night. You may not think about the advantages of a light until it burns out and you can't see what may lurk in the darkened waters.
How to tell if a pool light is a wattage or wattage?
If you find that there is no sticker or it is unreadable, there are a couple things you can try in order to identify the light. Check for a part number on the face ring and on the lens as manufacturers sometimes have part numbers molded into the parts. You can also see if the pool light bulb itself has any specs on it. If it is labeled with wattage, voltage and base type (R40 would be the base for a standard "flood" type bulb), you would have the necessary information needed to replace the bulb. Keep in mind this will not identify the gasket which should be replaced to ensure a proper seal on your pool light. Try measuring the outside diameter and thickness of the gasket and see if it matches the gaskets for the most common pool lights, the Hayward Astrolite or Pentair Amerlite .
How to get to the light bulb?
To get to the light bulb, you will need to remove the face ring, lens gasket and lens. Corrosion may have occurred so use care and the correct tools. Remove the screws or clamps holding the light fixture together. Gently pry off the face ring and then the gasket and lens. Clean any old gasket residue from the surface on the lens using a damp rag.
How to check if a new bulb works?
Find a friend to watch the light while you briefly turn on the electricity. This is to confirm that the new bulb actually works. These lights are not made to be turned on out of the water, so this has to be a very quick check.
Do you need a replacement pool light bulb?
You will first need to purchase the correct replacement pool light bulb and lens gasket for your light fixture. There is not one standard replacement bulb and gasket for all pool lights. That would be too easy! If you already know the make and model of your pool light, go to our Light Parts page to find the proper bulb and gasket.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Where is the manufacturer's name on a pool light?
The manufacturer name, model number, voltage and wattage of pool lights is typically found on a sticker on the back of the light housing (usually where the cord of the light attaches to the housing).
Why is my light bulb dimming?
This could be caused by various issues. Open up the fixture and make sure there isn't any water inside behind the lens. Dry the lens if it is wet. The dimming bulb may also need to be replaced.
What to do if light fixture is leaking?
If you’re worried that the light fixture may be leaking, you can also purchase a new rubber gasket to seal the fixture and prevent water from getting in .
What is the screw that holds a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock.
How to remove a pool light?
Roll up your sleeves, stick your arm beneath the surface of the water, and unscrew the screwlock. If the light is low on the side of your pool, or if your arm is too short to reach, you’ll have to get into the pool to unscrew the screw-lock and remove the fixture.
How long to bleach LED lights?
If the globe surrounding your LED is sealed, and there are no tabs or screws holding the piece together, place the light in a 2% bleach concentrate for 24 hours.
How many testimonials does wikihow have?
wikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 23 testimonials and 91% of readers who voted found it helpful, earning it our reader-approved status.
How to test if pool light works?
Turn the power on for 2-3 seconds to test the light and see if it works. Go back to the circuit breaker or pool electrical box and flip the switch back to “on.”. See if the light turns on. If it does, immediately turn the switch back to “off.”.
