Moen Kitchen Faucet Collar Diverter
- Locate the cap covering the set screw that holds the handle. It's plastic, and it bears the blue/red Moen logo. ...
- Remove the set screw with a hex wrench. ...
- Lift off the handle. ...
- Unscrew the Phillips screw holding the temperature limiter and lift it off the valve housing. ...
- Unscrew the retaining nut holding the cartridge in place using locking pliers. ...
Full Answer
What is the middle handle on a Moen shower?
What is a diverter collar?
What is a spout diverter?
How to get a spout off a valve?
Can a Moen shower valve fail?
Can you replace a Moen shower diverter valve?
Can you use a Moen sprayer without a repair?
See 4 more
About this website
How do you remove a Moen diverter stem?
Use pliers or a 3/4 deep wall socket wrench to unthread the brass diverter nut (#7) counterclockwise from the valve body (#9) and with pliers pull the diverter stem straight (#8) out.
How do you replace a Moen tub diverter?
0:372:26Bathtub Spout/Diverter Replacement EASY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it should slide right out you can see. Here. That's where the allen key goes in once you finishMoreAnd it should slide right out you can see. Here. That's where the allen key goes in once you finish doing that you can go ahead and put your new spout. In.
Where is the diverter on a Moen kitchen faucet?
In some models, the diverter is installed in the valve body; on other models it is installed around the valve body under the spout. If it is one of these models, make sure the spout is cleaned as well. If the side spray does not shut off completely, it would also need to be replaced.
How do you replace diverter valve?
Diverter Valve on a SpigotUnscrew the set screw. See how the spigot is attached to the wall. ... Unscrew spigot from the wall. Be careful! ... Wash Supply Pipe. Make sure that you clean off any bits of gunk from the supply pipe. ... Replace new spout on the copper pipe. ... Test it and make sure it works!
How does Moen tub spout diverter work?
A diverter tub spout will have a lift rod that you pull up and push down on to divert the water between the showerhead and tub spout. A non-diverter tub spout will not have a lift rod (generally, used in a tub only or a three handle tub and shower configuration).
How do you fix a broken shower diverter?
0:142:34How To Replace A Broken Shower Diverter - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd removing the seal from around the diverter it twists off turn left to loosen. If it's too tightMoreAnd removing the seal from around the diverter it twists off turn left to loosen. If it's too tight you might need to wedge a screwdriver in underneath to help loosen it up.
How do I know if my kitchen faucet diverter is bad?
Uneven water flow, low pressure when the pressure at other faucets seems all right, or troublesome switching back and forth from spray head to sink spout can be caused by a malfunctioning diverter valve or by a restricted hose.
Can you replace a faucet diverter?
If your diverter has a rotating valve, unscrew the nut at the stem of the diverter and remove the entire valve. If it has a gate-type valve, unscrew the threaded tub spout. Replace the diverter. To be sure you purchase the correct replacement, bring your old diverter with you to the store.
How does Moen diverter work?
How Do Shower Diverters Work? The water pipe that connects to your tub faucet also extends vertically to your showerhead. When the diverter valve is open, water flows directly through the faucet and into the tub. However, when you want to take a shower, you lift the knob or lever to close the diverter valve.
Do I need to turn off the water to change a diverter valve?
If you're only working on the diverter, you don't need to turn off the water supply to the faucet. While working, place a cloth over the tub drain to prevent any dropped screws from going down the drain. Some showers use a diverter built into the tub spout activated by lifting a button on the spout.
How do you remove a faucet diverter?
0:512:53Maintenance: Remove a Diverter - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlease note the diverter is located on the back of the housing. Using needlenose pliers carefullyMorePlease note the diverter is located on the back of the housing. Using needlenose pliers carefully remove the diverter by pulling the blade.
How do I know if my shower diverter valve is bad?
Here's a quick list of some problems a homeowner might experience related to diverter valves and what each one can mean.Water, Water Everywhere! One of the first signs that your shower diverter may be in trouble is leaks from the tub faucet while taking a shower. ... Valve Won't Engage. ... Rusty Water in the Tub.
How do I remove a Moen diverter tub spout?
There will be a small hole in the bottom of the tub spout, if you see a screw, you have a CC (Slip Fit) tub spout. If there is no screw, you have an IPS (threaded) tub spout. IPS (Threaded)- Threaded directly onto the pipe from the wall. Unthread the tub spout counter-clockwise to remove.
How do you remove an old tub diverter?
Step 1: Remove any caulking around the wall end of the tub spout with a putty knife or razor. Step 2: Unscrew the tub spout in a counterclockwise rotation until the tub spout is removed off of the brass adapter. Step 3: Use a 1/8" hex/Allen wrench and un tighten the Allen screw counterclockwise.
How do you fix a broken tub diverter?
How to Repair a Shower DiverterTurn off the water supply to your shower.Seal off your drain with tape so that small screws or other important parts are not lost down the drainpipe.Tighten the screws behind the faceplate of the diverter valve. ... Disassemble the shower diverter. ... Replace the diverter.More items...•
How do you remove a diverter tub spout?
0:143:21Repair Leaking Tub Spout Diverter Pull in Shower Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we'll take a look inside the tub spout in a little bit but first let's check out the washer. AndMoreSo we'll take a look inside the tub spout in a little bit but first let's check out the washer. And it looks fine maybe it just needs a little bit of cleaning. So when we look inside of the tub spout.
100885, 189801, 100886 Diverter Service Kits - Moen Solutions
Preparation: The water supply shut off valves must be turned off- see article How to Turn Off the Water Supply to the Faucet.; Recommended Tools: Pliers, Needle-Nose Pliers; The following instructions assume the handle and associated handle pieces have been removed.
How to contact a cartridge nut?
If you have an imbedded cartridge nut and would like additional help, feel free to contact us or call us for assistance at 1-800-BUY-MOEN ( 1-800-289-6636 ): 1224-install.mp4. Video Player is loading. Play. Mute.
What is the number to call for a faucet nut?
If you have an imbedded cartridge nut and would like additional help, feel free to contact us or call us for assistance at 1-800-BUY-MOEN ( 1-800-289-6636 ).
Is Moen faucet backed by a lifetime warranty?
Moen products have been manufactured under the highest standards of quality and workmanship. Most Moen faucets are backed by Moen's Lifetime Limited warranty. For more information about your Warranty, please visit our Warranty Information page.
Does the 4000 cartridge have a removal video?
This 4000 Cartridge does not have a Removal & Installation Video. Feel free to contact us or call us for assistance at 1-800-BUY-MOEN ( 1-800-289-6636 ). We're happy to help. TWO HANDLE FAUCET CARTRIDGES: Cartridge 1224 - Two-handle replacement cartridge (hot or cold).
What is the middle handle on a Moen shower?
If you have a Moen shower faucet with three handles, the middle handle is the shower diverter, and the actual valve takes the form of a plastic stem with holes in the end that control water flow. The procedure for replacing the diverter stem on a Moen shower valve, as detailed on the Moen website, calls for a screwdriver, socket wrench and needle-nose pliers, and you don't have to turn off the water to do it.
What is a diverter collar?
The two most common diverter styles are a collar that fits around the base of the valve or a button that fits inside it. Once you have the diverter in hand, you'll be able to match it to what you find inside the valve, and the procedure for replacing it — once you get the spout off — will be self-evident.
What is a spout diverter?
The spout diverter is that little button on the top or side of the spout that you pull up to get the shower to come on. It's fairly common for the seals on these types of diverter to fail, and because they aren't easy to remove from the spout, you usually have to replace the whole spout.
How to get a spout off a valve?
To get the spout off, grasp it firmly and wiggle it as you pull upward. Once it clears the O-rings, it will pop right off to reveal the diverter, which is either a collar that you can lift off or a button that you can pull out of the valve body with needle-nose pliers.
Can a Moen shower valve fail?
Don't worry, you probably won't ever have to do that, because a built-in diverter in a Moen shower valve seldom fails. Diverters on the spout can fail, though, and the same is true if your faucet has a Moen diverter stem. Both are fairly easy to replace.
Can you replace a Moen shower diverter valve?
The diverter on a Moen shower faucet works in the same way as a kitchen faucet. If the diverter is built into the valve, you can't replace it without replacing the valve. Don't worry, you probably won't ever have to do that, because a built-in diverter in a Moen shower valve ...
Can you use a Moen sprayer without a repair?
This is more of an annoyance than it is a serious problem, and many people simply continue to use the faucet and sprayer without doing any repairs. However, replacing a Moen diverter valve is not a complicated thing to do.
