Spray a liberal amount of penetrating oil onto the front and back sides of the pulley hub until they are thoroughly soaked. Spray the pulley retaining bolt and pulley shaft with the oil. Allow about 30 minutes to two hours for the penetrating oil to loosen the rusted pulley and other parts.
How do you replace a bad pulley on a lawn tractor?
When a bearing within the pulley goes bad, you will hear squealing and grinding. When this happens, you must pull the pulley off the spindle so you can replace the bearing. Do this with a spindle puller or gear puller. Remove the mower deck from the lawn tractor.
What does the pulley on a lawn mower do?
The two largest pulleys hold the mower blade in place. The smaller pulleys are idler or tensioner pulleys, and they are there to help route the belt in the correct direction. When a bearing within the pulley goes bad, you will hear squealing and grinding.
What causes a lawn mower belt to squeal?
There are different reasons for each pulley. The two largest pulleys hold the mower blade in place. The smaller pulleys are idler or tensioner pulleys, and they are there to help route the belt in the correct direction. When a bearing within the pulley goes bad, you will hear squealing and grinding.
How do I replace the pulley on my Kenmore dryer?
Remove the screws that hold the pulley guards over the pulleys and then place the pulley guard off to the side. Remove the bolt from the center of the pulley with a wrench.
How to remove pulley guards?
What are the two largest pulleys on a lawn mower?
What is a spindle pulley?
About this website
How do you replace a pulley on a riding lawn mower?
1:403:19Craftsman Riding Lawn Mower Large Deck Pulley #532196106 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the nut unthreaded remove the old pulley. Before you install the new large deck pulley firstMoreWith the nut unthreaded remove the old pulley. Before you install the new large deck pulley first confirm that the mounting bolt and belt guide are in position. Slide the new pulley on to the bolt.
How do you remove a pulley from a riding lawn mower deck?
1:273:29Craftsman Riding Lawn Mower Spindle Pulley #532195945YouTubeStart of suggested clipEnd of suggested clipNow use the 7/8 inch socket to loosen and unthread the pulley mounting dot we recommend using anMoreNow use the 7/8 inch socket to loosen and unthread the pulley mounting dot we recommend using an impact driver to make this easier with the nut removed lift off the old pulley.
How do you install a pulley on a lawn mower?
1:543:54Briggs & Stratton Lawn Mower Spring & Pulley Replacement #498144YouTubeStart of suggested clipEnd of suggested clipAnd remove the old rewind spring and pulley from the housing install the new rewind spring in pulleyMoreAnd remove the old rewind spring and pulley from the housing install the new rewind spring in pulley by aligning the spring hook with the housing post rotate the pulley to make sure the spring is
How do you remove the crankshaft pulley on a riding lawn mower?
0:315:06How to remove a stuck drive pulley on your Briggs and Stratton, Kohler, or ...YouTubeStart of suggested clipEnd of suggested clipSo i'm pulling down on the pulley. And pushing up on the gun. And. Just. Don't slip and hit theMoreSo i'm pulling down on the pulley. And pushing up on the gun. And. Just. Don't slip and hit the pulley it's come off a couple times but i've not damaged the pulley.
How do you remove a pulley without a puller?
Can You Remove the Power Steering Pump Pulley Without a Puller?With the pump taken off the vehicle, place it in a vice and use a piece of metal pipe and a hammer to tap the wedge between the pulley and the pump.Heat the center of the pulley with the blowtorch and pull it off.More items...•
How do you remove an engine pulley?
1:213:03How to Remove a Crankshaft Pulley in Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipThey get the puller assembly. Put it over and get one nut bolt and screw it into the little hole.MoreThey get the puller assembly. Put it over and get one nut bolt and screw it into the little hole. Then screw another bolt and washer until the hole on the opposite side you have both on snug.
How do you replace the pulley on a Craftsman riding mower?
1:303:17Craftsman Riding Lawn Mower Idler Pulley, Middle #532194326YouTubeStart of suggested clipEnd of suggested clipWith the nut removed pull off the old pulley install the new idler pulley by sliding it onto theMoreWith the nut removed pull off the old pulley install the new idler pulley by sliding it onto the mounting bolt. Hold the bolt in place as you re thread and tighten the nut.
How do you remove the mandrel pulley on a lawn mower?
1:133:38Replacing a Mandrel Assembly on a Riding Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut a wood blocks between the blade and mower deck to keep the cutting blade from moving remove theMorePut a wood blocks between the blade and mower deck to keep the cutting blade from moving remove the pulley mounting nut and detach the pulley. Pull out the wood block and flip the mower deck.
Which side of belt goes against pulley on lawn mower?
4:066:31How To Install A Belt On A Riding Lawn Mower Tractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe V side of the belt goes into your V pulley. That is correct right there.MoreThe V side of the belt goes into your V pulley. That is correct right there.
How do you remove a belt pulley?
0:344:11Belt Tensioner Pulley, How to replace (EASY and CHEAP) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt I get down in here loosen that holy pull the bolt out. And then pull the pulley off.MoreIt I get down in here loosen that holy pull the bolt out. And then pull the pulley off.
How do you remove the pulley on a John Deere engine?
Lay under or near the John Deere engine.Fit the proper-sized socket onto the bolt that holds the drive belt pulley to the base of the engine's crankshaft.Hold the pipe wrench with one hand, and with your other hand unscrew the bolt using the socket wrench.Pull down on the pulley until it slides off the crankshaft.
How do you remove the pulley from a John Deere mower deck?
9:4417:21How to change the belt, pulleys and spindle on your 42" John Deere ...YouTubeStart of suggested clipEnd of suggested clipSocket. Got it off. Next we're going to remove the spindle from the deck using our 10 millimeterMoreSocket. Got it off. Next we're going to remove the spindle from the deck using our 10 millimeter socket it has four bolts holding. It.
How do you remove a mandrel pulley?
1:133:38Replacing a Mandrel Assembly on a Riding Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut a wood blocks between the blade and mower deck to keep the cutting blade from moving remove theMorePut a wood blocks between the blade and mower deck to keep the cutting blade from moving remove the pulley mounting nut and detach the pulley. Pull out the wood block and flip the mower deck.
How do you remove a pulley from a keyed shaft?
Start by removing the threaded fastener that holds the pulley in place, loosening the pulley nut, and prying off the pulley with a pry bar or screwdriver. Then, grip the key, which is the semicircular piece inset into the shaft, with pliers and pull it off. You can also use a gear puller to remove the key.
How do you remove a belt pulley?
0:344:11Belt Tensioner Pulley, How to replace (EASY and CHEAP) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt I get down in here loosen that holy pull the bolt out. And then pull the pulley off.MoreIt I get down in here loosen that holy pull the bolt out. And then pull the pulley off.
6 Steps For How to Remove Pulley from Riding Lawn Mower
5. Remove The Pulley. Lock the 3 jaws of the spindle puller under the pulley and position the screw in the center of the pulley so that it’s resting on the spindle shaft. Use a wrench to turn the screw clockwise. As you turn it, the jaws will pull the pulley off the spindle.
How to Get a Rusted Pulley Off a Lawn Mower Motor
How to Get a Rusted Pulley Off a Lawn Mower Motor. Riding lawn mower motor pulleys are made of metal and can rust, especially in an older mower and a mower left exposed to the elements. The ...
How to remove pully from mower deck spindle - Restorations ...
:omg: I need help on how to remove the pulley from a 42 mower deck spindle. I would like to remove the last two spindles from my mower deck to repaint the shell but cannot figure out how to get them off without destroying them. Any suggestions would be greatly appreciated. In trying to pry on the...
How to remove pulley guards?
Remove the screws that hold the pulley guards over the pulleys and then place the pulley guard off to the side.
What are the two largest pulleys on a lawn mower?
The two largest pulleys hold the mower blade in place. The smaller pulleys are idler or tensioner pulleys , and they are there to help route the belt in the correct direction. When a bearing within the pulley goes bad, you will hear squealing and grinding.
What is a spindle pulley?
Spindle pulley. Wrench set . Most mowers have several pulleys. If you look at the mower deck on your lawn mower, you will see several pulleys mounted to the top. There are different reasons for each pulley. The two largest pulleys hold the mower blade in place.
How to remove pulley guards?
Remove the screws that hold the pulley guards over the pulleys and then place the pulley guard off to the side.
What are the two largest pulleys on a lawn mower?
The two largest pulleys hold the mower blade in place. The smaller pulleys are idler or tensioner pulleys , and they are there to help route the belt in the correct direction. When a bearing within the pulley goes bad, you will hear squealing and grinding.
What is a spindle pulley?
Spindle pulley. Wrench set . Most mowers have several pulleys. If you look at the mower deck on your lawn mower, you will see several pulleys mounted to the top. There are different reasons for each pulley. The two largest pulleys hold the mower blade in place.
