Remove the three torx-head screws along the bottom, front panel of the Whirlpool washer. Grab both sides of the bottom panel with your hands. Pull down on the panel while pulling the bottom of the panel away from the washer to expose the water pump.
How can I Reset my Whirlpool duet washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
- The motor has now been reset and is ready for you to start a cycle.
Is your Whirlpool duet dryer not spinning?
The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear.
Where is the drain pump on a whirlpool duet?
The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door. Unplug your Whirlpool Duet washer power cord from the wall outlet. Find the screws securing the lower access panel to the washer cabinet. Remove the screws with a 1/4-inch nut driver.
How to replace a seal on a whirlpool duet washer?
Pull the seal off the lip surrounding the door opening and push the seal inside the opening. Remove the front door panel by undoing the two screws on the bottom corner tabs, followed by the two screws on the top corner tabs.
Where is the drain pump on Whirlpool Duet washer?
Pull the bottom of the access panel toward you and pull it down to release it from the washer. The drain pump is under the Duet washer drum and has two hoses.
How do you replace a pump on a Whirlpool front load washer?
0:017:10Replacing the Drain Pump (Whirlpool Part # W10130913) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to show you how to change the drain pump on your washer. And it's a really easy job allMoreWe're going to show you how to change the drain pump on your washer. And it's a really easy job all we're going to need is a quarter inch nut driver 5/16 nut driver a flat blade screw driver and a
Where is the drain pump on a Whirlpool front load washer?
0:493:36Whirlpool Alpha Front-Load Washer Drain Pump Replacement ...YouTubeStart of suggested clipEnd of suggested clipUse a 5/16 inch socket or nut driver to unthread the drain pump mounting. Screws. With the screwsMoreUse a 5/16 inch socket or nut driver to unthread the drain pump mounting. Screws. With the screws unthreaded you can pull the old pump.
How do you test the pump on a Whirlpool Duet washer?
0:262:51Front Load Washer Won't Drain - How to Test the Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo set your meter domes. And touch the two terminals. And we're getting sixteen. So this motor isMoreSo set your meter domes. And touch the two terminals. And we're getting sixteen. So this motor is good basically and that's one test we'll move on to another test.
Why is my Whirlpool front load washer not draining?
The drain hose may be too far down inside the drainpipe (standpipe) or laundry tub. Drained water can siphon back into the washer if the drain hose extends too far. Make sure that the drain hose does not extend more than 4.5" (113 mm) into the drainpipe or laundry tub.
How much does it cost to replace a drain pump on a washing machine?
The price of a new washing machine pump is $25 to $40 on its own, not including labor. When hiring a professional, repair prices range from $200 to $450.
Where is drain pump on front load washer?
0:241:43How To: Clear The Drain Pump On Your Front Load Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe drain pump filter is usually located somewhere on the lower front of the washer.MoreThe drain pump filter is usually located somewhere on the lower front of the washer.
How do you clean a front load washer drain pump?
1:013:02Front Load Washer Pump Clean Out - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe filter clockwise to slow or stop the water flow while you empty the tray. Remove any particlesMoreThe filter clockwise to slow or stop the water flow while you empty the tray. Remove any particles in the filter. And slide the filter back into place turn the filter clockwise.
How do I clean the pump on my Whirlpool washing machine?
0:462:10Cleaning the Drain Pump Filter on a Front-Load Washer with no Access ...YouTubeStart of suggested clipEnd of suggested clipCheck inside the filter housing for any debris rinse. The filter clean remove the rubber seal. AndMoreCheck inside the filter housing for any debris rinse. The filter clean remove the rubber seal. And clean that to replace. The seal if it's damaged to prevent water leakage reinstall the rubber seal.
How do I know if my washing machine pump is bad?
The most common complaints are all obvious, and all involve wastewater. A common complaint is that the water in the washing machine drum will not drain, or that the washing machine has stopped mid-cycle with it still full of water.
How do I know if the pump is broken on my washing machine?
When the drain pump is either blocked or faulty these are the top symptoms that will be reported:Water in washing machine won't drain.Washing machine stopped full of water.Washing machine won't spin.Washing machine won't drain.
How do I know if my drain pump is clogged?
1:564:23How to Diagnose Washing Machine Drain and Pump Problems - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the noises are happening during the drainage. Then that could be an issue with the drainage pump.MoreIf the noises are happening during the drainage. Then that could be an issue with the drainage pump. If you've checked all of these areas for blockages.
How do I access the pump on my Whirlpool washing machine?
0:373:33Whirlpool Front-Load Washer Replace Drain Pump #WPW10425238YouTubeStart of suggested clipEnd of suggested clipSlide the panel to the right to fully detach disconnect the drain pump wire connector. Use pliers toMoreSlide the panel to the right to fully detach disconnect the drain pump wire connector. Use pliers to release the clamps securing the drain hose to the pump and pull the hose. Off.
How do I clean the drain on my Whirlpool front load washer?
0:462:10Cleaning the Drain Pump Filter on a Front-Load Washer with no Access ...YouTubeStart of suggested clipEnd of suggested clipCheck inside the filter housing for any debris rinse. The filter clean remove the rubber seal. AndMoreCheck inside the filter housing for any debris rinse. The filter clean remove the rubber seal. And clean that to replace. The seal if it's damaged to prevent water leakage reinstall the rubber seal.
How do you clean the pump on a Whirlpool washing machine?
Douse the pump with a spray solvent and scrub the interior with an old toothbrush. Remove as much of the dirt and debris as you can. Flush the pump with water for several minutes to ensure that it is clean.
How do you unclog a washing machine drain pump?
2:113:17Washer Repair: How to Unclog the Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipChoose a flat blade screwdriver release the spring clips you can slide the pump. Completely off andMoreChoose a flat blade screwdriver release the spring clips you can slide the pump. Completely off and access it or remove it completely.
Why does my Whirlpool water pump jam?
If the filter cup inside the pump fails to catch the item, it could catch inside the impeller and cause the pump to jam. Cleaning out the pump and removing any items impeding the impeller can repair your water pump and get your Whirlpool washer working again.
Why is my Whirlpool washing machine not draining?
When the water fails to drain from your Whirlpool front-loading washer, you may have a problem inside the water pump. Small items can travel from your washtub, through the drain holes, through the washtub drain line and into the pump. If the filter cup inside the pump fails to catch the item, it could catch inside the impeller and cause ...
How to clean a pump that is not caught by filter cup?
Reach inside the pump housing to clean any debris not caught by the filter cup. Insert an inspection mirror into the housing to view the impeller inside the pump. Look for any debris that may have jam med the impeller, keeping in from spinning. Remove the pump if it appears you have an object caught in the impeller.
How to get rid of obstruction in pump?
Look into the outlet port to see the back of the impeller for the obstruction. Attempt to shake the obstruction from the pump. Alternatively, use needle-nose pliers to grab any obstruction from the pump.
How to clean a septic tank filter?
Twist the handle on the front of the pump to the left to release the cover. Pull the cover from the pump housing along with the attached filter cup. Wipe the cup clean with a paper towel.
How to catch water from a water pump?
Fold a hand towel and place it under the pump to catch spilled water. Use channel pliers to compress the lugs on the spring loaded hose clamps securing the inlet and outlet hoses to the back of the pump. Move the clamps back, pull both hoses off, and withdraw the pump.
Why won't my washing machine shut off?
If your machine won’t shut off, or if it fails to drain, several possible causes might exist. The drain pump filter could be clogged, a foreign object like a sock might be blocking the drain hose or the drain pump is bad. Also, a foreign object such as a button might have broken the pump impellor or the motor might have burned out.
How to clean a washer that won't run?
First, try giving it a good cleaning. Use a cotton swab dipped in rubbing alcohol to clean the latch and any contact points. This will remove the lint, dirt, and product build-up that may be interfering with the electrical circuit.
What causes water to back up in washer?
Be sure the washer's drain hose is not inserted too far down the standpipe. It should only be inserted about six to eight inches. A severe clog in the drainage line could also cause a back-up of drainage water that seeps back into the washer.
Why is my washer accumulating water?
If the standing water is clear and clean, it is probably accumulating due to a failed inlet valve on the washer.
Where is the door lock tab on a door switch?
Located on the bottom of the door switch/lock unit is a tear-drop shaped tab.
Is Whirlpool a Cabrio?
Whirlpool is a leading manufacturer of washers and dryers around the world including the Cabrio and the Du et models of washer and dryers. The Duet models are a popular line; however, as with any home appliance, there can be Duet washer and dryer problems and a need for repairs.