how do you change a swamp cooler float

Instructions

• Open Up the Swamp Cooler. Remove the access panel on the side of the swamp cooler to gain access to the float valve and...
• Disconnect the Water Supply Line. Disconnect the water supply line by removing the 1/4-inch nut connecting the supply...
• Remove the Old Float Valve. Hold the valve with one pair of pliers and remove the housing nut with a second pair. If...

Full Answer

How do I choose the best float valve for my swamp cooler?

The cost of a new float valve can vary quite a bit, but even the best models are not very expensive. It's best to purchase a valve in the mid-range or better. Low-end valves tend to be hard to adjust to the correct water level and usually don't last as long as better valves. Shut off the water supply to the swamp cooler.

How do you turn off the water to a swamp cooler?

Shut off the water supply to the swamp cooler. There should be a dedicated valve on the unit's cold water supply line; if not, shut off the water to the house at the main shutoff or at the water meter. Remove the access panel on the side of the swamp cooler to gain access to the float valve and water line.

Why is my swamp cooler leaking water?

If the pads on your cooler are worn, replace them for a new set before using the swamp cooler.You should then check the float valve. Water may be impeded from flowing into the reservoir by a broken valve, and this can cause leaks.

How do you replace a float valve on a pool pump?

Install the new float valve in the same position as the old one. As you tighten the nut, make sure that the float will go up and down perpendicular to the water level. You may have to hold the float valve in place and tighten the nut at the same time, so the valve doesn't turn.

How do you change a float valve on a swamp cooler?

0:362:55How To Repalce A Swamp Cooler Float - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the socket on one end and on the swamp cooler float will actually hold one end of it with ourMorePut the socket on one end and on the swamp cooler float will actually hold one end of it with our hands and start loosening the nut to remove the swamp cooler float.

What does the float in a swamp cooler do?

Float. The evaporative cooler float is found on the bottom of the swamp cooler. When the water in the bottom of the swamp cooler reaches a certain level, the float rises on top of the water and shuts off the water supply valve. If this float stops working, the swamp cooler may not work or may overflow.

How do I adjust the water level in my swamp cooler?

2:192:44How to Adjust a Float Valve for Proper Water Level Settings - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater level if the float valve needs adjusted it's a very simple process there's a set screw on theMoreWater level if the float valve needs adjusted it's a very simple process there's a set screw on the side of the valve that controls the angle of the arm loosen. The setscrew adjust. The arm angle.

Why is my swamp cooler leaking water?

If the pads on your swamp cooler are the wrong size or placed incorrectly, water can get through and drip onto your floor. Cracked reservoir: If water is dripping from the bottom of the swamp cooler, and the float valve isn't the culprit, you likely have a cracked reservoir.

Do swamp cooler pads need to be changed every year?

Generally, it is recommended to clean the pads at least once every year or twice a year (before and after use) and replace them after 2-3 years.

How do you change the pads on a swamp cooler?

2:486:11How to replace Evaporative Swamp cooler pads - YouTubeYouTubeStart of suggested clipEnd of suggested clipVery simple you just push them in there with your fingers. They.MoreVery simple you just push them in there with your fingers. They.

How do you set a water float?

0:210:57How to Adjust a Toilet Float - YouTubeYouTubeStart of suggested clipEnd of suggested clipEither way you'll have a float adjustment screw like this one just turn it clockwise to lower theMoreEither way you'll have a float adjustment screw like this one just turn it clockwise to lower the water level to that wench from the top height. Check by flushing.

How long should I run the pump on my swamp cooler?

Most evaporative coolers without thermostats have separate switches for the fan and pump. If your unit lacks a thermostat, allow your pump to run a few minutes before turning on the fan. This saturates the cooler pads.

How do you remove a float valve?

0:202:25How to Replace a Toilet's Concentric Float Valve : Toilet MaintenanceYouTubeStart of suggested clipEnd of suggested clipThe first thing you want to do is shut off the water at the base of the toilet and drain all theMoreThe first thing you want to do is shut off the water at the base of the toilet and drain all the water in the back of the tank. After that's done go ahead and remove the back of the tank.

How high should the water be in a swamp cooler?

Check the water level in the bottom tray. It should be about one inch below the top of the tray, and below the top of the overflow pipe. If the water level is too high or too low, adjust the float arm. Make sure your float valve is working properly.

Do you leave water pump on for swamp cooler?

You need to have the pump on while running the cooler, to keep water running through the unit. A lot of times we will respond to repair calls where the pump was not turned on and only hot air was being pushed in the home by the fan.

How do you fix a leaking evaporative cooler?

Inspect the drain hole on the bottom of the cooler for leaks. If you see water leaking, check to see that the overflow pipe is screwed securely into place in the drain hole. Tighten the overflow pipe. If that doesn't work, you may need to replace the drain fittings and/or the overflow pipe.

Why is my water cooler leaking from the bottom?

Most often, water leaks are caused by cracks and holes in the water jug, not the cooler itself. Sometimes when the jugs are being transported, they incur damage resulting in tiny cracks or holes. Other times, when the air pressure of a jug changes, it may start to leak.

How do I stop my cooler from leaking?

0:153:59How to Fix a Leaking Water Dispenser/Water Cooler (It may be ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to spin them clockwise. And make sure they're both tight that could cause the cooler toMoreYou want to spin them clockwise. And make sure they're both tight that could cause the cooler to leak from the spigots. It could also uh if if these if it seems like these are very loose.

How do I know if my swamp cooler pad is bad?

The evaporative cooler pad in your system should be examined regularly for damage, preferably prior to the start of each season. Signs to look for that indicate excessive wear and tear are a loss of thickness, rips, cracks and fraying edges. If you notice any of these signs, it's likely time to replace the pad.

How do you remove calcium deposits from swamp cooler pads?

#3 How to Remove Calcium Deposits from Swamp Cooler Pads The best cleaner is a simple mix of white vinegar and water. You should clean the water pan reservoir at the bottom of the cooling unit at least once a month throughout the season to prevent minerals from building up inside.

How often should you drain a swamp cooler?

Keep reading to get all of your questions answered. An evaporative cooler should dump water every six to 12 hours if it has a dump-style drain valve. It should also dump when it turns off. The minimum standard for dumping water is once every 24 hours.

How often should swamp cooler pads be replaced?

every 3-5 yearsFor homeowners that have Mastercool swamp coolers and a water softening system on their home, you should clean the pads annually and replace them every 3-5 years.

How often should aspen pads be replaced?

every three to five yearsAspen cooling pads generally need to be changed right at the beginning of every season or perhaps sooner, depending on how many mineral deposits have built up on them since their last changing. Cellulose pads are designed to last a little longer. You might need to only change them every three to five years.

How many years does an evaporative cooler last?

But, while swamp coolers don't cost much to buy, they are a lot of work and money to maintain. Not only that, they are only warrantied to work for 5 years. Refrigerated air systems can last up to 20 years if properly maintained.

Why replace a swamp cooler float?

It might be corroded and rusted out. When it breaks your swamp cooler will keep on filling with water causing it to over flow possible making a flood. Now that you have turned off the water to the swamp cooler remove the doors. And you are ready to remove the water line.

How to get a nut off a cooler?

To help get the nut off. Remove the float and put the new float in. Install the new nut on the float. And hold the float with your hand. And tighten the nut with the socket. Make sure when you tighten the nut that the float is straight in the cooler. So where the water comes out it is straight.

Why do swamp coolers need to be repaired?

Another common need for swamp cooler repairs is caused by the fan breaking down. This may be caused by a number of factors. Remove the fan from the cooler, and examine the condition of the fan paddles. If they are damaged or corroded, discard the fan and start again. Look at the motor and belt which drives the fan.

How to get swamp cooler out of retirement?

Once you get your swamp cooler out of retirement, you will need to perform a quick check of the machine. Plug it into a safe socket (which has a circuit breaker device installed), and then operate it for a full cycle.

What to do if swamp cooler pads are worn?

If the pads on your cooler are worn, replace them for a new set before using the swamp cooler.You should then check the float valve. Water may be impeded from flowing into the reservoir by a broken valve, and this can cause leaks. Replace the valve is necessary.

What is swamp cooler?

The swamp cooler is a water-based device that cools the air by increasing the humidity. There are many complex parts to a swamp cooler, including the water reservoir, the air pumps, the electrical connections, and then fan. A lot of these items can become broken just by sitting in storage during the winter, so you will need to practice ...

How to get mold off a washing machine?

Remove mold by using a combination of water, vinegar, and bicarbonate of soda, and scrub away at the inside of the machine.