How to remove and replace the belt on a Craftsman riding lawn mower?
- Step 1: Disconnect the spark plug First, the thing you need to do is to turn off the ignition switch and remove the key. Next, you will have to pull the mower hood upwards and disengage the spark plug wire.
- Step 2: Disassemble the mower deck ...
- Step 3: Pull out the old belt ...
- Step 4: Install the new belt ...
- Step 5: Reconnect the mower deck ...
Full Answer
How to replace a mower drive belt?
Replacing the Motion Drive Belt
- Park the lawn tractor on a level surface and press the parking brake.
- Move the attachment clutch lever, which is located to the right of the steering wheel, down into the "Disengaged" position.
- Pull the attachment lift lever, which is slightly right of the attachment clutch lever, forward to place it in the lowest position.
How to replace drive belt on statesman riding mower?
How To Repair the Drive Belt on a Riding Lawn Mower
- Position the mower to change the lawn mower belt. ...
- Check the engine temperature before replacing the lawn mower belt. If the engine is hot, allow the exhaust system to cool down before attempting any maintenance.
- Detach the spark plug wire. ...
- Remove the cutting deck and battery. ...
- Loosen the transaxle pulley. ...
- Relieve tension on the upper drive belt. ...
How do you change drive belt on Toro Lawn Mower?
● Front-wheel drive lawnmower:
- – Step 1: Preparation of the mower. This step was the same as described above. ...
- – Step 2: Remove the components. Next, you need to remove the components such as the belt cover and baffle, mower blades, traction spring, and belt guide.
- – Step 3: Removal of the worn-out belt. ...
- – Step 4: Reassembly. ...
How to install mower blades on your Craftsman riding mower?
Instructions
- Disconnect the spark plug. Park the tractor on a level surface and set the parking brake. ...
- Pull off the mower deck. Lower the mower deck to its lowest position. ...
- Remove the old blade drive belt. ...
- Install the new blade drive belt. ...
- Reinstall the mower deck. ...
- Reconnect the spark plug. ...
How do you change a belt on a CRAFTSMAN riding lawn mower?
0:003:57How to Replace the Belt on a Craftsman Riding Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust take it off every pulley. Slide it out push it back in put it around every pulley. The onlyMoreJust take it off every pulley. Slide it out push it back in put it around every pulley. The only difference is is the belt rides on the back side of the belt on this idler pulley.
How many belts are on a CRAFTSMAN riding lawn mower?
two beltsUsually there are two belts. One goes around two pulleys, a front pulley under the motor and one on the mower deck.
How does the Deck Belt go on a CRAFTSMAN Riding Mower?
1:493:06Craftsman Riding Lawn Mower Deck V-Belt Replacement #532429636YouTubeStart of suggested clipEnd of suggested clipInstall the new deck belt by aligning it on the outer pulleys with the v-groove side facing. In thenMoreInstall the new deck belt by aligning it on the outer pulleys with the v-groove side facing. In then align the belt on the inner pulleys with the flat side facing.
What size Deck Belt does a CRAFTSMAN riding lawn mower take?
CRAFTSMAN 42-in Deck Belt for Riding Mower/Tractors (0.53-in W x 96.5-in L)
Do you have to remove mower deck to replace belt?
To replace this belt, the deck should be off the lawn mower. You'll crawl underneath and locate the idler pulley(s) and loosen the cap screw at the center of the pulley to allow a wiggling movement in the pulley.
What is the difference between a deck belt and drive belt?
The "Deck Belt" goes around the pulleys right above the blades on the deck and then to a double pulley. The "Drive Belt" on your mower goes from the transmission, around an Idler pulley then over to the double pulley I mentioned before. The Drive belt also plays a role in making the wheels turn.
How do you put a belt back on a riding lawn mower?
1:082:12putting the BELT back on a riding mower (LT 1045 cub cadet)YouTubeStart of suggested clipEnd of suggested clipSo you can get it onto the pulley on the motor. When you do get the belt onto the motor pulley theMoreSo you can get it onto the pulley on the motor. When you do get the belt onto the motor pulley the spring pulls the belt tight. So now you have tension. So you can mow the grass.
How do you change a riding mower deck belt?
1:043:20Riding Lawn Mower Cutting Deck Belt Replacement Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can refer to your operators manual tighten the idler pulley nuts you loosened put the beltMoreYou can refer to your operators manual tighten the idler pulley nuts you loosened put the belt keeper rod back in place around the engine pulley.
How do you tighten the belt on a CRAFTSMAN lawn mower?
How to tighten the belt on a craftsman lawnmower, step by step:Step 1: Gather the necessary tools and remove the spark plug.Position your lawnmower on a leveled surface.Step 3: Remove the mower deck.Step 4: Tighten the belt bracket.Step 5: Tighten all pulley connections.Step 6: Double-check the blades.
What size belt does a CRAFTSMAN 42in deck take?
AYP / Craftsman / Sears Deck Belt fits 42", 46" & 50" Decks built since 1995. Size: 1/2" x 95-1/2". Replaces part numbers 532144959 and 144959.
How long is a CRAFTSMAN 42 inch Deck Belt?
AYP / Craftsman / Sears Deck Belt fits 42", 46" & 50" Decks built since 1995. Size: 1/2" x 95-1/2".
What size belt goes on a CRAFTSMAN 46 inch deck?
CRAFTSMAN 46-in Deck Belt for Riding Mower/Tractors (0.53-in W x 17-in L)
What size belt do I need for a 46 inch deck CRAFTSMAN?
CRAFTSMAN 46-in Deck Belt for Riding Mower/Tractors (0.53-in W x 17-in L)
How long is the deck belt on a CRAFTSMAN LT2000?
What is the craftsman LT2000 drive belt size? It's 1/2 x 95.5 inches.
How long is the CRAFTSMAN deck belt?
Drive Belt Craftsman mowers have primary and secondary drive belts. Both belts range between 42 to 50 inches long, depending on the mower's model. Craftsman's riding and push mowers use drive belts.
What size is the drive belt on a CRAFTSMAN LT1000 Riding Mower?
If you have an LT1000 riding mower, you may be able to do a Craftsman LT1000 belt replacement on your own. These mowers have 42-inch, heavy-duty decks, and the manufacturer's replacement drive belt part measures 1/2 inch by 95 1/2 inches. Its part number is 144959.
How to remove drive belt from crankshaft?
Remove one end of the drive belt by pulling the belt off the crankshaft pulley and then removing the crankshaft pulley .
How to keep a lawn mower from shifting?
Now that you have taken safety precautions by removing the spark plug or battery you will want to tilt your mower back on its handle. Secure the mower handle by strapping it down to the workstation or using something soft and heavy to keep your mower from shifting when working on it.
How to remove a crankshaft blade?
With your work glove on, firmly place your hand on the blade where the wooden block wedges it. Loosen the blade bolt and remove it from the crankshaft along with the blade and blade support.
How to remove the bottom drive cover?
Remove the bottom drive cover screws and debris shield bolts and remove the shield. Gently twist and remove it from the crankshaft pulley.
Do you need to align a crankshaft pulley when reinstalling?
There are indentations on the pulley that need to be aligned when you reinstall it. Roll the new drive belt onto the crankshaft pulley so it sits securely on the pulley.
Can you work on a push mower on the ground?
Make sure you secure your mower when using a workbench so it does not move and potentially fall off the bench. If a workbench or raised work surface is not available, it is fine to work on your push mower while it is on the ground.
Can you move a deck out of a lawn mower?
Now that the cable and spring are removed, verify you didn’t miss disconnecting any other component attaching your deck to the mower. You can completely move the deck out from underneath your lawn mower once you have confirmed nothing from your deck is attached to your mower .
How to check if mower belt is loose?
To see if your current drive belt is loose or not, start your engine and push your throttle lever to the highest. Next, engage the cutting blades by pushing the lever upwards.
Where is the drive belt located on a lawn mower?
It is situated underneath the mowing deck in case of riding lawnmowers. The belts usually wear out after continued use.
Why is my Craftsman mower not mowing?
Ever witnessed your Craftsman lawnmower not mowing properly or leaving patches of uncut grass? A loose drive belt might be the very reason. Luckily, the entire process is relatively easy, and all you’ll need for the adjustment is just a socket wrench. If you’ve never performed self-maintenance on your Craftsman lawnmower before, then don’t worry as we dissect this information for you in a step-by-step approach.
How to release belt keepers?
Roll the belt off the engine pulley and release the belt keepers.
What is a transmission belt?
Transmission belts in machine design may be of the V-type or synchronous design. V-belts have a wedge-shaped cross-section. Friction is the only force keeping the belt attached. On the other hand, synchronous belts have a notched profile along their inner circumference, much like gears. They are generally mounted on gears and pinions and are used in timing operations.
Why do drive belts wear out?
The belts usually wear out after continued use. Due to elongation in their tensile cords , drive belts have been known to become loose with time. Most often, the remedy is a replacement. However, in cases when elongation isn’t much, you can always adjust the belt tension, and we are looking at that in this article.
How to tell if a belt is loose?
Spring: The cable that comes from the lever is connected to a spring. Touch the spring to see if it’s completely stretched or loose. Also, touch your belt at the same time and notice if it appears loose. If it does, we shall move on towards the next step, adjusting the belt tension.
How to seal a Craftsman gas tank?
You need to tightly cover the fuel tank’s face well with a plastic sheet to prevent leaks. Open the fuel tank, cover the opening with a plastic sheet, and put the lid back on. Sealing the tank will prevent fuel loss during your work, especially if you need to tilt the Craftsman mower. If sealing it is a problem, you can also remove the gas from the tank.
What is a Drive Belt?
The drive belt is responsible for transferring power from the engine to the moving lawnmower components. It connects the engine of your machine to the crankshaft. If the drive belt is faulty, the power transmission will be affected, reducing the machine’s performance. Therefore, a healthy drive belt is crucial for the performance of a Craftsman lawnmower or any other lawnmower. To fix the problem, you should replace the faulty drive belt with a new one.
What to do if you find fault with lawn mower drive belt?
So if you find any fault with the drive belt of your lawnmower, you should take immediate steps to replace it. But at first, let’s know some important data regarding this replacement: Now it’s time to gather the necessary tools that are required to replace the drive belt.
How long does it take to replace a drive belt?
Approximate time frame: 20-30 minutes. Now it’s time to gather the necessary tools that are required to replace the drive belt. These tools will make your task smooth and toilless.
Why does my craftsman mower lose its ability to cut grass?
The reason behind this is grass gets stuck to the mower’s blade and the drive belt is torn down. Now come to the point.
How to turn a blade counterclockwise?
Using a socket wrench, turn the blade’s screws counterclockwise. Be careful when opening the screws so that the blade can not fall down.
How to replace crankshaft pulley?
Replace the crankshaft pulley in its previous position by rotating it clockwise. Attach the drive belt with the crankshaft pulley carefully.
How to free up drive belt?
Locate the crankshaft pulley and rotate it counterclockwise. When you bring out the crankshaft pulley, you can easily free up the drive belt.
How to settle a transmission belt?
Pull the front hood upwards and settle the drive belt with the transmission pulley. When the settlement is done, lower the front hood.
Symptoms common to all riding mowers & tractors
Choose a symptom to see related riding mower and lawn tractor repairs.
Repair guides common to all riding mowers & tractors
These step-by-step repair guides will help you safely fix what’s broken on your riding mower or lawn tractor.
Articles and videos common to all riding mowers & tractors
Use the advice and tips in these articles and videos to get the most out of your riding mower or lawn tractor.