Instructions
- Remove the agitator Pull the fabric softener dispenser off of the top of the agitator. ...
- Remove the agitator dogs Pull the top auger off of the agitator assembly. ...
- Install the new agitator dogs Push the new agitator dogs into the cam. ...
- Reinstall the agitator Push the agitator down on top of the agitator shaft. ...
- Restore the power Plug the washer into the electrical outlet. ...
How do you replace the agitator dogs on a Kenmore washer?
Take off the plastic bearing that rests on top of the agitator dogs. Remove the agitator dogs from their holder and replace them with new ones. After the new agitator dogs are installed, place the plastic bearing back on the cam and put the cam back into the agitator.
How do you remove the agitator from a whirlpool washing machine?
Pull the fabric softener dispenser off of the top of the agitator. Pull the dust cap out of the agitator. Use a 7/16" socket with an extension to remove the agitator bolt. Pull the agitator out of the washer and set it on a work surface.
Should I remove the agitator from my Maytag front load washer?
This will reduce the cycle time by a few minutes, so it is recommended that you remove the agitator only if you have a top-loading HE washing machine. The agitator is a critical part of any front-load Maytag washer. It functions as the primary agitator, moving clothes in a circular motion to help remove stains and dirt from your clothing.
How do I know if my washing machine agitator dogs are bad?
If you are able to manually spin it in both directions, the agitator dogs are no longer functioning properly and will need to be replaced. If you have noticed your washing machine’s agitator is working to a much weaker degree, the agitator dogs could possibly be the issue.
How do you remove the agitator from a Maytag top load washer?
0:573:07How To: Whirlpool/KitchenAid/Maytag Agitator Assembly WP22004042YouTubeStart of suggested clipEnd of suggested clipAnd simply pull straight up which will remove. It. You're going to use a ratchet with 1/2 inchMoreAnd simply pull straight up which will remove. It. You're going to use a ratchet with 1/2 inch socket and extension to remove the bolt that's down in the center that holds the agitator in place.
How do you remove the agitator from a old Maytag washing machine?
0:092:09How to replace the Agitator Auger and Base Assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll see a spot where there's a quarter inch hex head screw. We're going to loosen that screw aMoreYou'll see a spot where there's a quarter inch hex head screw. We're going to loosen that screw a couple of turns. And then we should be done if that agitator. Completely off of the agitator shaft.
How do I put my agitator back together?
2:345:36Whirlpool/KitchenAid/Maytag Complete Agitator Assembly 285565YouTubeStart of suggested clipEnd of suggested clipFirst thing we're gonna do is put the seal on the inner cap all you have to do is stretch. AroundMoreFirst thing we're gonna do is put the seal on the inner cap all you have to do is stretch. Around get it in the groove. Then we can lift off the upper agitator.
How do you take an agitator apart?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd then write down the center of the agitator as a little wound yard remove that just hold theMoreAnd then write down the center of the agitator as a little wound yard remove that just hold the agitator as you unscrew anticlockwise.
How do you remove a Maytag Performa agitator?
0:372:00See how to check & replace the agitator in a Performa washerYouTubeStart of suggested clipEnd of suggested clipScrew in the holding screw and install the fabric softener dispenser remove the fabric softenerMoreScrew in the holding screw and install the fabric softener dispenser remove the fabric softener dispenser remove the agitator holding screw remove the top part of the agitator on.
How do you clean the agitator on a Maytag washing machine?
You don't need to clean your agitator separately from the rest of the washer. When you run a cycle to clean the tub, the agitator will be cleaned along with it. If you notice dirt or grime on the agitator, wipe it down with a damp cloth and mild soap or affresh® washing machine cleaning wipes.
How long do agitator dogs last?
The plastic material used to make the dogs just deteriorates over time and after aprox ten years needs to be replaced. The dogs also wear down due to heavy loads, and or overloading.
How do you change an agitator dog washer?
0:421:41How to Replace the Agitator Dogs on a Whirlpool Vertical ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitatorMorePull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitator bolt. Pull the top auger off of the agitator assembly. And set it on a work surface dump.
How do you remove clothes from under agitator?
1:423:49Clothes Stuck in the Wash? Here's How to Get Them Out! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt up so I guess it can face so what I did. So I got this rope. This is already done so I'm doing itMoreIt up so I guess it can face so what I did. So I got this rope. This is already done so I'm doing it easier than it was. But you got to slide it underneath.
Can you unscrew the agitator from a washing machine?
With the bolt sufficiently loosened, you can pull the agitator straight up to remove. Alternatively, on some models where the agitator has an upper and lower section, you may need to use a square drive bit to unthread a retainer that will allow you to pull the upper portion of the agitator off first.
How do I fix my agitator?
0:296:51How to Fix Washer Top Agitator Not Working - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes this comes off by hand other times you may need to actually use the ratchet. Hold theMoreSometimes this comes off by hand other times you may need to actually use the ratchet. Hold the agitator down bottom in place he needs.
How do I clean my washing machine agitator without removing the agitator?
Turn off water, add in baking soda and vinegar. Dip cleaning cloth in water/baking soda/vinegar mixture, and clean all around the inside and top of the washer. Use Q-tips, a pipe cleaner, or toothbrush to reach the nooks and crannies and remove all the built up gunk. Rinse and scrub the inside of the agitator.
How do you loosen the agitator bolt?
1:134:08How To: Whirlpool/KitchenAid/Maytag Agitator Bolt WPW10076270YouTubeStart of suggested clipEnd of suggested clipOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonnaMoreOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonna have to reach down and hold it while you break the bolt. Free.
How do you remove clothes from under agitator?
1:423:49Clothes Stuck in the Wash? Here's How to Get Them Out! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt up so I guess it can face so what I did. So I got this rope. This is already done so I'm doing itMoreIt up so I guess it can face so what I did. So I got this rope. This is already done so I'm doing it easier than it was. But you got to slide it underneath.
How do you get a stuck agitator out of a washing machine?
ANSWER: To remove a tightly-fitted agitator or one that has become firmly glued in place by soap residue, first unplug the washer and remove the agitator cap. Then, if there is room between the bottom edge of the agitator and the tub bottom, work a completely deflated bicycle tire in underneath the agitator.
What size bolt is in Maytag agitator?
Washer agitator bolt with rubber gasket and thread sealant. Head is 7/16 inches in diameter.
What is the one way ratcheting motion of an agitator dog?
That one-way motion combines with the back-and-forth motion at the bottom of the agitator to move garments through the water during the agitate cycle.
How to remove agitator spring retainer?
Tip: If your agitator has a plastic spring retainer above the agitator bolt with a 1/2" square hole at the top, use a 1/2" ratchet drive extension and ratchet to remove the spring retainer.
What to do if your top load washer spin basket is damaged?
If the spin basket on your top-load washer is damaged, you can replace it with a new one. Just follow these step-by-step instructions.
Why does my washer spin when the basket is empty?
If the washer spins when the basket is empty but not when the basket is full, the problem could be the clutch assembly. These steps explain how to replace it.
What do you wear to protect your hands?
Wear work gloves to protect your hands.
What to do if your timer doesn't advance?
Replace the timer if it doesn't advance or work properly.
Is it dangerous to repair an appliance?
Warning: Undertaking repairs to appliances can be hazardous. Use the proper tools and safety equipment noted in the guide and follow all instructions. Do not proceed until you are confident that you understand all of the steps and are capable of completing the repair. Some repairs should only be performed by a qualified technician.
How many bolts does a washer agitator have?
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.
What is a washer retainer ring?
This is a genuine OEM thrust spacer for your washer , and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in the agitator assembly of many direct drive washing machine models.
What is an agitator repair kit?
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.
What is the agitator in a washer?
The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction.
How to hold a bolt in the socket?
To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket.
How to remove plastic cup from agitator?
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
What happens if your agitator is not working?
If your agitator is no longer agitating properly, your clothes will not tumble, and will not be washed properly. The agitator repair kit includes an agitator cam, 4 directional cogs, a bearing, thrust spacer, inner cap seal, and a washer. It is constructed of plastic and rubber, and comes in black/white. See more...
Why is my agitator dog not working?
Symptoms The Agitator Dogs Are Failing. As we said earlier, a malfunctioning agitator is often caused by worn agitator dogs. Usually, the failure is simply due to normal wear and tear or old age, but overloading your washing machine on a regular basis can also speed up the deterioration of the part. The top section of your agitator should only spin ...
How to tell if agitator is working?
Taking the agitator apart is the only way to tell if this is truly the problem. The upper half of your machine’s agitator pulls the clothing to the bottom of your appliance tub. If the agitator is not working properly, due to failing agitator dogs, your clothes will remain at the top of the tub. Safety Warning: As with any washer repair, safety ...
How to repair a washing machine that is unplugged?
After you have unplugged your washing machine, open the lid and remove the top cover of the agitator. Reach into the agitator and take out the dust cap. With the dust cap removed, you should see a bolt in the middle of the agitator.
What is an agitator dog?
Agitator dogs, which are also known as dog ears, ratchet cogs, or agitator cogs control what direction the top section of a dual action agitator moves in. Basically, the upper part of your washer’s agitator should only move in a single direction, while the lower portion has the ability to rotate in multiple directions.
Why does my washer have a spindle?
That rotation dispenses the laundry detergent, keeps the load from clumping up in the washer’s tub and removes the dirt from your clothes. Like any part of an appliance, the agitator can malfunction. Often, the main culprit of a failing agitator is caused by worn agitator dogs. If you’ve never heard of agitator dogs, don’t worry, we’re here to help you better understand their function and how to replace them.
How to remove agitator dogs from holder?
To do this, simply pull the two sections apart. Once the top and bottom sections are disconnected, turn the top half upside down. The cam, which holds the agitator dogs will fall out. Take off the plastic bearing that rests on top of the agitator dogs. Remove the agitator dogs from their holder and replace them with new ones.
Can you spin an agitator in both directions?
The top section of your agitator should only spin in one direction. If you are able to manually spin it in both directions, the agitator dogs are no longer functioning properly and will need to be replaced.