Screw the cutting blade bolt into the blade spindle by hand with the flat washer facing the blade. Slide the wooden block between the new cutting blade and the cutting deck. Finish torque the cutting blade bolt with a socket and torque wrench; torque the cutting blade bolt between 27 to 35-foot pounds.
How do you change a cutting blade on a craftsman mower?
Slide the wooden block between the new cutting blade and the cutting deck. Finish torque the cutting blade bolt with a socket and torque wrench; torque the cutting blade bolt between 27 to 35-foot pounds. Remove the wooden blocks from the cutting deck and in front and behind the rear tires.
How often should I Change my Craftsman lawn mower blades?
Craftsman lawn mower blades need to be changed at least once a year and more frequently if your yard includes sand, gravel or rocks. These materials will prematurely wear and damage your blades.
How much does a craftsman lt1500 cost?
Craftsman LT1500 (42") 420cc 7-Speed Lawn Tractor Craftsman LT1500 (42") 420cc 7-Speed Lawn Tractor Click to enlarge RRP: Price: $770.00 SKU: Vendor: Brand: Craftsman Condition: Weight:
How do you sharpen a craftsman drill bit?
Sharpen Craftsman blade with a drill powered blade sharpener. Power the drill with the blade sharpener attached. Place the flat guide of the sharpener along the flat portion of the blade with the cutting edge slot into the bevel. Move the sharpener up and down the length of the blade edge.
How do you take the blades out of a Craftsman riding lawn mower?
1:283:51Craftsman Riding Lawn Mower Blade Replacement #532422719 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the bolt on threaded you can remove the old blade install the new cutting blade by aligning itMoreWith the bolt on threaded you can remove the old blade install the new cutting blade by aligning it on the spindle shaft with the sharp edge facing away from the deck.
Are Craftsman riding mower blades reverse threaded?
Are Craftsman Mower Blades Reverse Thread? Yes. The bolts that hold the mower blades on a Craftsman mower in place are reverse threaded. That means that to tighten the bolt you must turn it to the left (counterclockwise), and to loosen it you must turn it to the right (clockwise).
How do you remove a lawn mower blade without removing the deck?
1:427:38Change Your Riding Lawn Mower Blades Without Taking Off the DeckYouTubeStart of suggested clipEnd of suggested clipSo what I do is just set a little block of wood right here on the lip of the deck. And then put a CMoreSo what I do is just set a little block of wood right here on the lip of the deck. And then put a C clamp on it going underneath the deck. And what that's going to do is stop your blade from turning.
How do you change the blades on a craftsman lt1000?
0:001:05how to remove blades on LT1000 lt2000 lt3000 - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut. So reach right in underneath. And put one arm on the right to grab onto the ratchet and grab onMoreCut. So reach right in underneath. And put one arm on the right to grab onto the ratchet and grab on to the blade with your leather glove and give it a tug. And it comes right off quite easily.
Which way do you turn the bolt to remove a lawn mower blade?
To remove the blade, you must turn the blade's retaining bolt to the left, or counterclockwise. Before undoing the blade, tip the mower on its side with the engine air cleaner facing up and block the blade with a piece of wood so it can't turn.
How do you loosen a lawn mower blade nut?
2:434:17How to remove a stubborn mower blade nut - YouTubeYouTubeStart of suggested clipEnd of suggested clipLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So itMoreLike I say I've got to come along to prevent it from shifting. And I'm going counterclockwise. So it should loosen hopefully whoa there we went.
How do you change a blade on a Craftsman lawn mower?
1:182:20Replace Your Mower Blade: Lawnmower Tutorial from Sears ...YouTubeStart of suggested clipEnd of suggested clipHold the blade against the blade adapter with one hand and thread the blade bolt with the otherMoreHold the blade against the blade adapter with one hand and thread the blade bolt with the other holding. The blade with a gloved hand tighten the bolt with the torque wrench.
How do you use the blade removal tool?
0:352:44How to use a blade removal tool | Troy-Bilt riding lawn mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the side of the tractor deck is shown tighten the clamping screw on to the tractor deck untilMoreAnd the side of the tractor deck is shown tighten the clamping screw on to the tractor deck until the tool is firmly in place the tool should not slide on the edge of the mower deck.
Do lawn mower blades turn clockwise or counterclockwise?
Since most lawnmower blades turn clockwise, the bolt often goes counter-clockwise. To check the mower's bolt, you have to turn it off, remove the spark plugs, and lay the lawnmower on its side. The bolt sits in the middle of the blades.
How do you install a new blade?
0:241:37Replacing the Blade on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow let's get started disconnect the spark plug wire from the spark plug remove the fuel tank cap.MoreNow let's get started disconnect the spark plug wire from the spark plug remove the fuel tank cap. Place a plastic bag over the fuel tank opening and reinstall the fuel tank cap to prevent gasoline
How do you change the blade on a craftsman lt2000?
2:4917:33Craftsman LT2000 Lawn Mower Blade Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipMinutes. Let's go ahead and use my pliers and i've got my gloves on to just remove this first pin.MoreMinutes. Let's go ahead and use my pliers and i've got my gloves on to just remove this first pin. Got my pin removed. And now i am going to detach this arm by just pushing it back out.
How do you know if mower blade is upside down?
If on the right side, move the blade in a counterclockwise direction, and if on the left side, move it in a clockwise direction.) When doing this, this sharp edge of the blade should be the edge that leads. If it does, then you have the correct lawn mower blade position. If not, you need to flip it over.
Are riding lawn mower blades reverse thread?
The lawnmower blades itself is not threaded, but most nuts that held the blade in place are reverse threaded. The reverse thread helps to secure the blade on the drive shaft such that the rotation of the blade does not loosen the nut. It is important to note that not all lawnmowers use a reverse threaded nut.
Do lawn mower blades turn clockwise or counterclockwise?
Since most lawnmower blades turn clockwise, the bolt often goes counter-clockwise. To check the mower's bolt, you have to turn it off, remove the spark plugs, and lay the lawnmower on its side. The bolt sits in the middle of the blades.
How do you take the blades off a MTD riding lawn mower?
0:202:01MTD Lawn Mower Extreme Blade Replacement #942-0741X - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a piece of wood or a comparable sturdy object to hold the cutting blade in place then use a 5/8MoreUse a piece of wood or a comparable sturdy object to hold the cutting blade in place then use a 5/8 inch socket and strike it with a mallet to help loosen the mounting bolt.
How do you remove pins from a lawnmower deck?
1:136:05How to remove mower deck Craftsman YTS 3000 TractorYouTubeStart of suggested clipEnd of suggested clipAnd then that way you'll come off the mower deck. And then push the pin out the rod just be carefulMoreAnd then that way you'll come off the mower deck. And then push the pin out the rod just be careful don't pinch your hands. And then the rod should come right out the front of the machine.
How to remove dull blades from a blade spindle?
Slide the cutting blade from the blade spindle by hand , taking care not to cut your hands -- dull blades also can cut. Remove stubborn or stuck cutting blades with a ball peen hammer; tap the top of the blade slightly with the hammer to drive the blade from the blade spindle.
How to remove stuck blades from a hammer?
Slide the cutting blade bolt, lock washer and flat washer from the blade spindle by hand. Slide the cutting blade from the blade spindle by hand, taking care not to cut your hands -- dull blades also can cut. Remove stubborn or stuck cutting blades with a ball peen hammer; tap the top of the blade slightly with the hammer to drive the blade from the blade spindle.
How to prevent rusting on cutting blades?
Apply a light coat of all-purpose grease to the cutting blade bolt threads to prevent the bolt from rusting and seizing to the blade spindle. Slide the lock washer followed by the flat washer onto the cutting blade bolt.
Can a broken blade damage a riding mower?
Worn and dull cutting blades tear the grass rather than providing a clean cut, and tearing the grass leads to your lawn becoming vulnerable to scalding and fungus. Bent or broken blades can damage the riding lawnmower cutting deck belts and pulleys from harsh harmonic vibrations.
When You Should Seek a Professional Sharpening Service for Your Craftsman Blades?
Lawn mower repair shops typically offer a mower blade sharpening service. I have my mower blades sharpened by a professional. The reason I choose to not sharpen blades myself is because I can’t put a sharp consistent edge on my mower blade like the tech can.
Why does my Craftsman mower blade wear?
Your mower blade and deck are designed to create a suction in the deck that makes the grass stand tall. In doing so, the mower blades pick up more than just grass. The pick up debris, such as stones and dirt, that cause the Craftsman blade to wear sooner when you operate your mower in dusty conditions with increased levels of dirt and gravel in your lawn.
How to tell if mower blade is bent?
Park your mower on a level surface and measuring from the ground to one end of the blade. Rotate your blade 180 degrees to measure the other end of the blade. If there is more than an 1/8” difference, your blade is bent and should be replaced.
How to remove chips from lawn mower blade?
Chips and dings: Hitting items in the yard can result in chips and dings in your mower blade. You can typically remove small chips from your blade by sharpening it. If you see large gouges in the blade, you should replace it.
What does it mean when a lawn mower blade is balanced?
The blade is properly balanced. This will reduce vibration, damage to your mower and personal injury.
How to reinstall a mower blade?
Some mower blades are marked “Bottom” to help you determine which side should be on the bottom or facing the ground. Install the blade and secure with the blade bolt. Tighten the blade bolt between 75-90 ft. lbs. using a torque wrench. Do not over tighten as you can damage the spindle.
How to balance a blade?
If you don’t have a blade balancer available you can place the center hole of the blade over a nail on the wall. If one end of the blade hangs lower than the other end, you will need to sharpen the end that hangs lower until they are equally balanced on the nail. While this isn’t the most accurate way to balance your blade, it’s the best option when you don’t have a balancer.
Can you change blades without removing deck?
You should look for help from a family member or neighbor to avoid any accidents. That way, you’ll get it done faster and in a safer manner. Hopefully, this will help you change blades without removing the deck on your riding lawnmower.
Can you replace blades on Craftsman riding mower?
Even though the blade replacement process is supposed to be performed after removing the deck , you can still get the job done with the deck intact. So, if you’re looking to change blades on your Craftsman riding mower without removing the deck, follow the method mentioned below.
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
