How to Replace the Drum Support Rollers on a Whirlpool LE5200XTW0 Dryer
- Unplug the Whirlpool LE5200XTW0 dryer from the electrical outlet.
- Remove the lint screen and set it aside. Remove the two screws near the lint trap opening, using a Phillips screwdriver.
- Insert a putty knife into the crease between the dryer's top and front panel. ...
- Unplug the door switch wiring connector plug. ...
How do you replace the rollers on a dryer?
· http://www.partselect.com/PS347627-Whirlpool-349241T-Drum-Support-Rollers.htm?SourceCode=3&SearchTerm=PS347627 Click here for more information on this part, ...
How do you replace the drum on a whirlpool dryer?
How do you change the rollers on a Whirlpool dryer? Unplug the dryer. Pull the lint screen out of the housing in the top panel of the dryer. Use a Phillips screwdriver to remove the 2 screws that secure the lint screen housing to the top panel. Push a putty knife under the lid near the left and right edges of the front of the dryer.
How do you replace the drive belt on a whirlpool dryer?
· Need help replacing the Drum Support Roller (Part #WPW10314173) in your Whirlpool Dryer? Watch this how to video with simple, step-by-step instructions for a...
Can you replace a drum roller shaft on a Kenmore dryer?
Remove the plastic ring on the roller shaft. Pull the roller off of the shaft and remove the second plastic ring on the other side of the roller. Wipe the shaft with a rag to remove grease, dirt...
How do you remove a dryer roller?
InstructionsShut off the power. Unplug the dryer. ... Raise the top panel. Pull the lint screen out of the housing in the top panel of the dryer. ... Remove the front panel. ... Remove the drum. ... Remove the drum support roller. ... Install the new drum support roller. ... Reinstall the drum. ... Reinstall the front panel.More items...
How do I know if my dryer rollers are worn out?
1:325:17Electric Dryer Making Loud Noise - TOP 6 Reasons & Fixes - All DryersYouTubeStart of suggested clipEnd of suggested clipAnd you'll hear a grinding noise coming from the front of the dryer. If you've determined that they'MoreAnd you'll hear a grinding noise coming from the front of the dryer. If you've determined that they're worn out you'll need to replace them.
How much does it cost to replace dryer drum rollers?
Replacing the rollers in a dryer averages $100 to $150. The rollers sit behind your dryer's back panel and hold the drum in place to rotate smoothly. Most machines require two rollers. If they break or wear down, you may hear unpleasant noises coming from the appliance.
How do you remove the drum from a Whirlpool dryer?
1:104:01Whirlpool Electric Dryer Drum Assembly Replacement #W10757750YouTubeStart of suggested clipEnd of suggested clipNow carefully lift up the front panel to fully detach it from the cabinet. Reach under the drum andMoreNow carefully lift up the front panel to fully detach it from the cabinet. Reach under the drum and unthread the belt from the pulley and motor shaft. You can use the belt to help lift out the drum.
What does a bad dryer drum roller sound like?
When the rollers are slightly damaged, they are more likely to make a squeaky noise. As they completely wear out, the effect on the dryer drum causes a loud thumping noise.
Do you lubricate dryer rollers?
You use grease on your bearings because it stays in place and does its job. Get some emery paper and clean of those shafts and then apply a general automotive grease to the shaft and bearing and then reassemble. you could always just but a new bearing and shaft too.
How long do Whirlpool dryers last?
Generally, Whirlpool dryers have a lifespan of 8-12 years. However, some may last longer if you maintain it properly. But if your Whirlpool dryer is at least ten years old, replacing it is more reasonable. Repairing the 10-year-old dryer will likely cost less.
How do I lubricate my dryer rollers?
Locate the rubber-rimmed rollers with roller bearings at the back of the drying casing. Squeeze two to three drops of oil on the front and back of each roller bearing.
Is it worth fixing a 10 year old dryer?
It's recommended as a rule of thumb that if your dryer is close to 10 years old, you're better off replacing it outright, especially if the quote for repairs comes in high.
How do you change drum rollers?
4:1410:26Dryer Repair - Replacing the Drum Rollers (Whirlpool Part # 349241T)YouTubeStart of suggested clipEnd of suggested clipWe slide it on the shaft. Take your triangular retaining clip press it into place. Now reinstallMoreWe slide it on the shaft. Take your triangular retaining clip press it into place. Now reinstall support bracket slide it over the front of the shaft. Take your new spring clip push on nut.
Why is my dryer drum not spinning?
A broken drive belt is the most common reason a dryer won't spin. To fix this issue, turn the drum by hand. A working belt should provide some resistance, so if the drum turns very easily and loosely, the belt is probably broken.
How do you change a drum glide on a dryer?
2:284:17Dryer Front Drum Glide - How it Works & Installation Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipBe aware if the glide is secured with rivets you may need to drill out the rivets to remove the oldMoreBe aware if the glide is secured with rivets you may need to drill out the rivets to remove the old glide to install the new drum glide hook it on the bearing tab on the drum.
How to fix a Whirlpool dryer that is squealing?
Lower the top panel and push down firmly to snap the spring clips into place. Plug the Whirlpool LE5200XTW0 dryer into the electrical outlet. Run a drying cycle and listen to ensure there is no more squealing noise.
How to remove a belt from a dryer?
Reach under the drum and push the pulley to release the belt's tension. Remove the belt from the tensioner pulley and off of the motor pulley. Lift the drum and remove it from the dryer.
Why does my Whirlpool dryer make a grinding noise?
If your Whirlpool LE5200XTW0 dryer is making squeaking or grinding noises while operating, the drum support rollers may need to be replaced. These rollers support the drum as it rotates during the drying cycle. The rollers have bearings at the center that can wear out over time, causing the noise. This repair requires you to disassemble the dryer, but it can be accomplished with just a few tools.
How to reinstall a drum?
Reinstall the drum and place it on the rollers. Guide the belt over the motor pulley and then over the tensioner pulley. Turn the drum by hand to ensure the belt is tracking true. Be aware that the front of the drum is not fully supported yet.
Raise the top panel
Pull the lint screen out of the housing in the top panel of the dryer.
Remove the front panel
Use a slot screwdriver to release the locking tab on the wire harness plug for the door switch. Disconnect the wire harness. Use a 5/16-inch nut driver to remove the front panel mounting screws from the inside of the dryer.
Remove the drum
Note the configuration of the belt on the idler pulley and the motor pulley before removing it—take a digital picture of it so you know how to reinstall it.
Remove the drum support roller
Use a slot screwdriver to pry the triangular washer off the front of the drum support roller.
Install the new drum support roller
Push the new drum support roller onto the shaft and secure it with the triangular washer.
Reinstall the drum
Place the rear of the drum on top of the support roller that's on the rear panel inside the dryer.
Restore power to the dryer
Plug the dryer into the wall outlet. If it's a gas dryer, turn on the gas supply to the dryer.
What does a drum roller do on a dryer?
Home Maintenance. By William Machin. Drum rollers on electric and gas dryers support the drum while it rotates by means of a belt. When rollers become worn or damaged, the drum may make thumping noises or the clothes will come out with black smudges.
How to remove a pan head?
Remove the side and back panels using the appropriate tools to loosen the pan-head screws or hex-head screws that hold the pieces in place. Save the parts and fasteners for re-installation.
Where to install wood shims?
Install wood shims in the gap between the lower portion of the drum and the inner panel or frame member to prevent the drum from lowering when the rollers are removed.
Can you work on a clothes dryer?
Do not attempt to work on a clothes dryer if you are not confident you can correctly do the repairs. William Machin began work in construction at the age of 15, while still in high school. In 35 years, he's gained expertise in all phases of residential construction, retrofit and remodeling.
How do I replace a dryer drum?
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost. Read more...
What is included in a dryer roller kit?
The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does not include a belt or idler pulley and rollers are not sold individually. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble.
Why does my dryer make a squeaky noise?
If your dryer is damaged, it may be making loud, squeaking, and/or squealing noises while the drum is turning. This is from normal wear and tear. The drum may eventually stop turning all together. This is a sign the part should be replaced. This is one complete maintenance kit.
How long is a drum roller shaft?
Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.
How long does it take to repair a dryer drum?
This repair has been rated as "medium" difficulty by our customers, generally taking between 30 and 60 minutes.
Do dryers have drum rollers?
The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate.
What is a drum support roller kit?
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If your dryer is damaged, it may be making loud, squeaking, and/or squealing noises while the drum is turning. This is from normal wear and tear. The drum may eventually stop turning all together. This is a sign the part should be replaced. This is one complete maintenance kit. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. The parts are constructed of plastic, metal, and rubber, and come in black/white/silver.
