How to Change a Line in a Homelite Electric String Trimmer
- Step 1: Unplug the Trimmer You don't want the trimmer to switch on by mistake while you're working, so pull the extension cord off the plug on the trimmer handle. ...
- Step 2: Remove the Spool ...
- Step 3: Prepare Two Lengths of String ...
- Step 4: Wind the Two Lengths Separately ...
- Step 5: Replace the Spool ...
- Step 6: Free the Strings ...
Full Answer
How do you replace trimmer line?
Method 1 Method 1 of 3: Changing the Line on a Single-Line Trimmer
- Prepare the line. The length and width of line you need varies based on your trimmer. ...
- Make sure your trimmer’s engine is turned off. If it has a gearbox, make sure it is cooled down. ...
- Remove the retaining cap from the trimmer head. ...
- Locate the starter hole in the spool. ...
- Line up the retainer with the slot on the outside of the head. ...
How to replace string on a Homelite Weed Eater?
How to Restring a Homelite Weed Wacker
- Ensure that the trimmer is shut off and disconnected from all power. If the model is a gas-powered weed eater, remove the spark plug to avoid accidental startup.
- Push in the tabs on the side of the spool retainer, and pull the spool upward to remove it from the trimmer head.
- Remove any old string still on the spool.
How to replace fuel line in Homelite gas Trimmer?
- Note the hole in the fuel tank in which the fuel filter attaches.
- Note the hole in the choke plate through which the filtered "in" line from the fuel tank passes to the carburetor.
- Note where on the carburetor the "in" line connects.
- Note where the carburetor "out" line passes through the choke plate.
How to replace string trimmer Edger line?
Part 2 Part 2 of 3: Replacing the Old Line
- Thread your new line into the holes designated on your spool. Purchase a .080 inch (2.0 mm) diameter round monofilament line from a hardware store.
- Wind the line around the spool, following the arrows on the spool. Feed the line through the hole and begin to wrap it around the spool.
- Secure the line to the spool and cut the line. ...
What size string does a Homelite trimmer use?
What is a Homelite electric trimmer?
How to put string in a trimmer head?
How to remove a trimmer head?
See 1 more
About this website
How do I change the line on my Homelite trimmer?
0:293:37How to replace string on Homelite grass trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipSide. So I want it to be pretty close to even on each on either side. And so that's so that's evenMoreSide. So I want it to be pretty close to even on each on either side. And so that's so that's even now.
How do you Respool a Homelite trimmer?
0:452:09* Homelite weedeater string refill how to - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay. So it looks like this you got it all lined up alright just drop the area to the ground. Now weMoreOkay. So it looks like this you got it all lined up alright just drop the area to the ground. Now we're going to take this. And we're gonna turn it one way or the other hold on clockwise.
How do I change the trimmer thread?
0:262:19Replacing a Weed Eater String (String Trimmer Line) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe bump knob and spool by pushing the tabs on the sides of the trimmer. Head. Cut a new piece ofMoreThe bump knob and spool by pushing the tabs on the sides of the trimmer. Head. Cut a new piece of string trimmer line typically 10 to 20 feet and thread half of it through the holes of the spool.
What size string does a Homelite Weedeater use?
0.080-inchIt uses dual 0.080-inch cutting lines on a 17-inch diameter head.
How do I remove the Headmer from my Homelite electric trimmer?
0:242:16HOW TO Remove Homelite Grass Trimmer Head - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes. I even put a bit of oil in there before. I put it back together.MoreSometimes. I even put a bit of oil in there before. I put it back together.
How do you fill a double line trimmer?
1:144:13Restring a Dual Feed Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst thing we have to do is to remove the cap. This is usually done by pressing in the tabs on bothMoreFirst thing we have to do is to remove the cap. This is usually done by pressing in the tabs on both sides. And lift off we then can remove the spool.
How do I change the string on my head trimmer?
0:163:58How to Replace a String Trimmer Head - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil it locks in place okay. Right there it just locked. So now the other thing is most time they'MoreUntil it locks in place okay. Right there it just locked. So now the other thing is most time they're threaded opposite. So usually it's righty tighty lefty loosey in this situation it's the opposite.
How do you remove the trimmer spool?
0:130:51How to Change a String Trimmer Replacement Spool - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo remove the old spool press the tabs on the spool cover and pull the cover straight off next liftMoreTo remove the old spool press the tabs on the spool cover and pull the cover straight off next lift the spool out of the hub.
Who makes Homelite string trimmers?
Beginning in the late 1970s, Homelite gradually expanded its power equipment line to include string trimmers, leaf blowers, push mowers, and hedge trimmers. John Deere acquired the brand in 1994. Techtronic Industries acquired Homelite from John Deere in 2001.
What is the fuel mixture for Homelite trimmer?
Fuel Mixture This Homelite gas trimmer runs on a 50:1 mix of unleaded automobile gasoline and two-cycle engine oil. That is equivalent to 2.6 fluid ounces (80 ml.) of oil to one gallon of gasoline or 4 tsp. (20 ml.)
Are Ryobi and Homelite the same?
A: Yes Ryobi and Homelite are both currently owned and manufactured by the same company - TTI (TechTronics Industries) if the part number your machine uses is the same, the part is the same. Helpful?
How do you adjust the carburetor on a Homelite trimmer?
0:512:18How to Adjust the Carburetor on a Homelite Weed Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the screw clockwise until the trimmer head starts to spin. Back off the screw slowly until theMoreTurn the screw clockwise until the trimmer head starts to spin. Back off the screw slowly until the head stops spinning locate the high speed screw or the screw to the right of the low speed screw.
How do you take off a spool?
0:001:27How to Replace the Spool on an Electric Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst off there are two tabs one on each side that we will need to press in before we can remove theMoreFirst off there are two tabs one on each side that we will need to press in before we can remove the spool. Next we can pull that spool cover and spool housing out of our trimmer.
What is the fuel mixture for Homelite trimmer?
Fuel Mixture This Homelite gas trimmer runs on a 50:1 mix of unleaded automobile gasoline and two-cycle engine oil. That is equivalent to 2.6 fluid ounces (80 ml.) of oil to one gallon of gasoline or 4 tsp. (20 ml.)
How do you put a universal trimmer head on?
0:001:41Universal Bump Trimmer Head Installation Method 3 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt place the nut inside of the head attach the head on to the male Bolton. Make sure the headMoreIt place the nut inside of the head attach the head on to the male Bolton. Make sure the head attaches.
How to Thread a 13-inch Homelite Weed Eater | eHow
The 13-inch Homelite String Trimmer comes with a dual line system that uses an auto feeder to push out more line. This line can break easily against concrete, walls, and fences, requiring frequent line replacement. Inside the trimmer head, a removable spool houses the line, which can be replaced whenever the old line gets too short.
Amazon.com: 10 FT 12 AWG 3 Prong Replacement Power Cord, 20 Amp 12 ...
LAKCZIO will continue to bring you value-for-money products, and continue to improve our products and customer service. We hope that all our customers have a good shopping experience and our products can bring you practical help. Produst: 12AWG 3 Prong Open End Replacement Extension Cord. Help: 1.
Rope & String Lights | HD Supply
Give you property some flair with our selection of string and rope lights
What size string does a Homelite trimmer use?
They use 0.065-inch-diameter string, which is the lightest available. Manufacturers color-code trimmer string to make identification easier, and the color for 0.065-inch string is blue. Advertisement. Homelite electric trimmers are among the least expensive trimmers on the market.
What is a Homelite electric trimmer?
Homelite electric trimmers are for light-duty jobs, such as garden weed management and mowing small patches of lawn.
How to put string in a trimmer head?
Feed the ends of the two lengths of string through the holes in the trimmer head and set the spool back in place on the shaft inside the trimmer head. Orient the retainer cover so that the tabs line up with the notches on the trimmer head and then push it down until it snaps in place.
How to remove a trimmer head?
Grasp the two tabs on either side of the trimmer head and squeeze them together. This will free the spool retainer and allow you to lift it off the trimmer head. Lift the line spool out and pull out any old string that happens to be there.
What is a homelite weed eater?
The Homelite weed eater is a lightweight gas-powered string trimmer that is useful for cutting long weeds and general yard maintenance. Several models are available, and the procedure for replacing the string is the same for all of them. The spool accepts two separate lengths of 0.080 microfilament line that automatically advance when you tap the string head on the ground. While you can replace the spool with a pre-strung spool when it's empty, not every hardware store carries them, and it isn't difficult to rewind the existing spool with replacement string.
How to unscrew weed eater?
Lay the weed eater on a flat surface and turn it so the string spool is facing you. Grasp the spool with one hand and the string head that encloses it with the other. Rotate the spool counterclockwise to unscrew and separate it. Pull the spool out of the head, ensuring that the spring stays attached to the spool.
Can you replace a spool with a pre-strung spool?
While you can replace the spool with a pre-strung spool when it's empty, not every hardware store carries them, and it isn't difficult to rewind the existing spool with replacement string.
What is a Homelite string trimmer?
Homelite string trimmers, such as the model 26CS, are suitable for use by homeowners to help control grass and weeds in hard to reach areas around the lawn. Although changing the trimmer line is necessary due to normal operation, loading line onto a spool can be a chore for some.
How to line up a trimmer head?
Hold the trimmer head with one hand and the spool retainer with the other hand. Line up the arrows on the spool retainer with the line holes in the trimmer head by rotating the spool retainer.
How to feed a short length of line from a trimmer head?
Push down on the spool retainer and pull the line at the same time to feed a short length of line from the trimmer head. Connect the spark plug wire back to the spark plug for use.
What to brush before using a trimmer?
Brush any dirt, grass or debris from the trimmer head and spool retainer before starting to help make the line loading process easier to accomplish.
How to use a 15 foot line trimmer?
Insert one end of the 15-foot length of line into the hole on one side of the trimmer head. Push the line through and out the opposite side of the head. Pull the line until there are equal lengths on each side.
How to load line onto spool?
Turn the spool retainer counterclockwise to load the line onto the spool. Stop turning when there is about 6 inches of line extending from the head on both sides of the trimmer head.
How to tie trimmer line to spool?
Locate the starter holes in the spool. Insert the tip of the first length of trimmer line into one starter hole, and wind in the direction of the arrows. Wrap the line in neat, straight rows, to prevent jams later on. When there are about 5” or 6” of line remaining, snap it into the retainer on the spool to hold it in place. Repeat this process with the second line. At this point, the line ends should be at opposite sides of the spool, to match the eyelets on the outside of the tri mmer head.
How to keep trimmer line from jamming?
Locate the starter hole in the spool . Insert the tip of the trimmer line, and wind in the direction of the arrows. Wrap the line in neat, straight rows, to prevent jams later on. When there are about 5” or 6” of line remaining, snap it into the retainer on the spool to hold it in place.
How to replace a retaining cap on a spool?
Line up the retainer with the slot on the outside of the head. Replace the spool into the trimmer head. Remove the line from the retainer, and pull it through the slot to make sure it is feeding smoothly. Reattach the retaining cap.
How many halves does a double line trimmer have?
Double-line trimmers typically divide the spool into two halves (one fore each protruding line).
What happens if you buy the wrong width of line?
The length and width of line you need varies based on your trimmer. If you purchase the wrong width of line, the trimmer will not work correctly, so don’t waste your money by simply guessing at the hardware store.
How to remove retaining cap on a trimmer?
Remove the retaining cap from the trimmer head. This will probably involve either unscrewing it, pressing one or multiple tabs, or a combination of the two. Some models use different mechanisms for removing the spool. These should be designed to be relatively intuitive, but contact your trimmer’s manufacturer if you are having trouble figuring it out.
How long should a trimmer line be?
If you are not sure what size line your trimmer uses, check online—the manufacturer’s website often has instructions, and if not the customer service department should be able to help you.The length to which the line should be cut also varies, from around 10’ to 25’.
How to recognize a string trimmer?
Some manufacturers offer convertible string trimmers, and you can recognize these by the locking nut or snap-together connection about midway up the shaft. Loosen the nut or press the spring-loaded release and the shaft separates into two parts. These manufacturers usually supply brush-cutter attachments, and it's always best to use the one supplied by the manufacturer of your trimmer rather than a generic one. Simply push the section of shaft with the cutter head onto the section with the trimmer motor and either snap them together or tighten the locking nut, and that's it.
How to use a string trimmer as a brush cutter?
If your trimmer is equipped for it, you can separate the trimmer head and a section of the shaft and replace it with a brush-cutter attachment. If your trimmer doesn't have a shaft that comes apart, you can often unscrew the trimmer head and replace it with a brush-cutter blade. Brush cutters need more power than string trimmers, so with a few notable exceptions, you'll need a gas-powered string trimmer to make an effective brush cutter.
How to loosen a trimmer head?
If you examine the trimmer head, you'll see a small hole. Insert a nail into the hole to stop the spindle from turning while you unscrew the trimmer head. The spindle has reverse threads, so you have to turn it clockwise to loosen it.
What is the best tool to trim knee high grass?
When you have to clear woody brush or mow through knee-high grass, a brush cutter is a better tool.
What do you need to use a brush cutter?
A brush-cutter blade can throw rocks and wood chips in all directions at high speeds, so you need to wear protective equipment, including goggles, steel-toed shoes, gloves and heavy pants at a minimum . If you're working with a high-powered trimmer, you should wear a hard hat with a face shield.
Can you replace a trimmer head with a brush cutter?
If your trimmer is equipped for it, you can separate the trimmer head and a section of the shaft and replace it with a brush-cutter attachment. If your trimmer doesn't have a s haft that comes apart, you can often unscrew the trimmer head and replace it with a brush-cutter blade. Brush cutters need more power than string trimmers, ...
What size string does a Homelite trimmer use?
They use 0.065-inch-diameter string, which is the lightest available. Manufacturers color-code trimmer string to make identification easier, and the color for 0.065-inch string is blue. Advertisement. Homelite electric trimmers are among the least expensive trimmers on the market.
What is a Homelite electric trimmer?
Homelite electric trimmers are for light-duty jobs, such as garden weed management and mowing small patches of lawn.
How to put string in a trimmer head?
Feed the ends of the two lengths of string through the holes in the trimmer head and set the spool back in place on the shaft inside the trimmer head. Orient the retainer cover so that the tabs line up with the notches on the trimmer head and then push it down until it snaps in place.
How to remove a trimmer head?
Grasp the two tabs on either side of the trimmer head and squeeze them together. This will free the spool retainer and allow you to lift it off the trimmer head. Lift the line spool out and pull out any old string that happens to be there.