How to Replace Your Maytag Washer’s Water Inlet Valve Assembly
- 1. Unplug the washer and turn off the water supplies. First, unplug the washer. ...
- 2. Disassemble the machine to access the water inlet valve assembly under the console. First, you will need to flip the top panel of the washer over. ...
- 3. Remove the water inlet valve assembly. ...
- 4. Replace the water inlet valve. ...
- 5. Install the new wire harness. ...
- 6. Reassemble the machine. ...
How to save energy by not connecting to hot water line?
How long does it take for a washer to reset?
How to clean a clogged water hose?
What can restrict water flow in a hose?
Can a washer run with only one incoming water?
See 2 more
About this website
How do you check a water inlet valve on a Maytag washer?
1:552:50Washer Not Filling? Water Inlet Valve Testing, Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or aMoreDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or a washtub.
How do I remove my Maytag water inlet screen?
1:003:40How To: Whirlpool/KitchenAid/Maytag Inlet Valve Screen WP96160YouTubeStart of suggested clipEnd of suggested clipWe're just gonna reach in with a small flat-head screwdriver and try to break it free and pull itMoreWe're just gonna reach in with a small flat-head screwdriver and try to break it free and pull it out of the. Valve. Once you have the inlet valve screen out you can pull it off the washer.
How do you know if your water inlet valve is broken?
Signs pointing to a faulty inlet valve include:Leaks that fill the dishwasher when it's off.Inadequate water for a cycle. ... A bad inlet valve can lead to leaks from the dishwasher onto the kitchen floor. ... Most inlet valve malfunctions stem from a defective seal or solenoid failure.
Where is the water inlet valve on a Maytag?
2:096:12How To: Whirlpool/KitchenAid/Maytag Water Inlet Valve WP8540751YouTubeStart of suggested clipEnd of suggested clipIt's right here on the back of the valve.MoreIt's right here on the back of the valve.
How do you remove water from inlet screen?
1:102:56How To: LG/Kenmore Water Inlet Valve Filter Screen AGM73269501YouTubeStart of suggested clipEnd of suggested clipThe water inlet hoses from the washer. Use a towel to catch any water left in. There. Using theMoreThe water inlet hoses from the washer. Use a towel to catch any water left in. There. Using the pliers pull the old filter screens. Out.
Why is my Maytag washer dripping water inside?
The tub seal might be torn, causing water to leak from the seal. If the tub seal is leaking water, water may leak through the tub seal and into the tub bearings. This can cause the bearings to fail. For this reason, if the tub seal is leaking water, replace both the tub seal and the tub bearings.
How do you change a water inlet valve?
0:532:06How to Replace the Water Inlet Valve on a Whirlpool Vertical ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the water valve out of the washer. Set it aside for disposal push the new water valve intoMorePull the water valve out of the washer. Set it aside for disposal push the new water valve into position reinstall the mounting screws plug. The wire harness into the correct connector.
How long do water inlet valves last?
In most cases, the original valve should last an average of 9 years but some of the earlier part numbers have averaged 5 or 6 years. If and when a valve does go bad there are some obvious signs to look for.
Why is there no water going into my washing machine?
You could have a faulty lid or water level switch, or your hot and cold water supplies could be turned off or have kinks in the hoses. A clogged water inlet screen or a malfunctioning electronic control could also be the reason a washer isn't filling with water.
How do you change the inlet valve on a washing machine?
0:372:08Replacing the Water Inlet Valve on a Front-Load Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a Phillips screwdriver to remove the two mounting screws remove the old water inlet valveMoreUse a Phillips screwdriver to remove the two mounting screws remove the old water inlet valve assembly. Position the new water inlet valve assembly lining.
Where do I find the model number on my Maytag washer?
Where to Look:On the back, behind the control panel.Inside the washer lid, right bottom corner.On the back on the baseframe to the left.
What is a water inlet valve?
What Is a Washing Machine Water Inlet Valve? The washing machine water inlet valve on your washer is the part that connects the two water hoses to the machine, and it controls the flow of both hot and cold water.
How do you remove an inlet filter on a washing machine?
1 Remove the hot and cold water inlet supply hoses from the back of the washing machine. 2 Locate the inlet hose filter inside of the hot and cold water inlets on the back of the washing machine. 3 Remove the filters by pulling them straight out by the tab in the center of the filters.
How do I remove the filter from my Maytag washer?
1:573:58How To: Whirlpool/KitchenAid/Maytag Washer Filter Plug Kit 285868YouTubeStart of suggested clipEnd of suggested clipAnd pry the old filter. Out with a flat head screwdriver installing the new filters make sure thatMoreAnd pry the old filter. Out with a flat head screwdriver installing the new filters make sure that this tab goes to the center of the tub. And points at the transmission.
How do you remove an inlet filter on a Whirlpool washer?
0:171:56See how to clean or replace the water valve filters Whirlpool washerYouTubeStart of suggested clipEnd of suggested clipUse the skinny screwdriver to remove the filters. If the filters are full of sediment and rust cleanMoreUse the skinny screwdriver to remove the filters. If the filters are full of sediment and rust clean them if you can and if you can't clean them get new ones.
How do I remove the inlet hose from my washing machine?
0:491:34How to Replace Washing Machine Hoses - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn off the water supply valves. Usually located behind the washing. Machine disconnect the oldMoreTurn off the water supply valves. Usually located behind the washing. Machine disconnect the old hoses. First from the washing machine and then from the valves.
SOLVED: Washer will not fill with water - iFixit
William, the problem would have to be inside one of the water inlet valves. If your getting voltage to the valve and no water is entering the machine then the mechanics of the valve aren’t opening to let the water through. Sediment from the water can coat the inside of the valve with a cement... - Maytag Washer MVWB765W
Maytag Washer fills slowly or will not fill at all - Repair Clinic
Start Right Here Find appliance parts, lawn & garden equipment parts, heating & cooling parts and more from the top brands in the industry here. Click on Shop Parts, or select the kind of product you're working with on the left and we'll help you find the right part. SHOP PARTS
Not Filling or Long Fill - Product Help | Maytag
Thank you for your inquiry. Our chat service hours are Monday - Friday from 8 a.m. - 8 p.m. EST. Saturday from 8 a.m. - 4:30 p.m. EST.
What is the water inlet valve assembly on a Maytag washer?
The water inlet valve assembly controls and distributes water to different dispensers in your Maytag washer. But if the body cracks, water can leak throughout the machine. Over time, the solenoids can also fail and won’t distribute water correctly. You can replace this part yourself. Order replacement part #W10364988 for most Maytag washer models and follow these steps to install it.
How to lock a washer on a washer?
First, remove the belt and then carefully swing it down until it rests on top of the machine. Make sure the corner holes near the lid line up with the bolts on top of the washer. Once it’s down and in place. press it firmly down until you hear the locks engage.
How to connect a thermistor to a wire box?
Start with the blue thermistor wires. Insert the wires into each of the mounting tabs along the length of the wire box. Use a flathead screwdriver to carefully open the tabs and push the wires into place. Lace the end of it under the other wire harness and add a new zip tie to attach the one the rmistor wire to the other bunch of wires. Then plug in the thermistor wires.
How to get wire out of gray wiring box?
You may need to use a flathead screwdriver to pry the wire out of each tab without damaging either the wires or the plastic tabs. The wiring goes all the way to the right side of the gray wiring box. Once you’ve reached the right side, detach the two wide wire harnesses that slot into the right side of the box by depressing the mounting tabs on each one .
How to remove a hose head from a hose?
Each hose is clamped in place. Use pliers to compress and loosen the clamp. Then slide the clamp away from the hose head and remove each hose head from the ports.
How to secure a washer console?
Line up the five mounting tabs at the interior edge of the console with the body of the washer. Then flip the console over and click the three back tabs with the screws into place. Tighten the screws to secure the console.
Where is the blue thermistor wire?
Orient it so the blue thermistor wires are over the gray wiring box and the other half of the wiring harness is over the blue water inlet assembly. Lay it loosely on top so you can start installing the different elements of it.
What is the lid lock on a Maytag washer?
The lid lock on Maytag Bravos washing machines is a two-part mechanism. It has a magnetic switch that senses when the lid is in the closed position; it also has a locking tab that must be extended in the locked position to allow the washer to continue with any of its washing functions. The lid lock is responsible for three possible error codes: “ dU ” (Door/Lid cannot unlock), “ dL ” (Door/Lid cannot lock) and “ lid “ (Lid Opened) The lid lock can be checked for resistance in it’s various states with a voltmeter at the washing machine control board.
How many ways can a water inlet valve fail?
The water inlet valve can fail in three ways.
How many solenoids are needed for a washing machine?
Note: For water to flow through a dispensing cup or into the washing machine’s tub two valve solenoids must be energized at a time, the primary hot and/ or cold-water inlet valves and one secondary valve. (Detergent dispenser, fabric softener dispenser, bleach dispenser, or fresh fill) “ Water Valve Diagnostic Tests ”
What is the suspension system on a Cabrio washer?
The suspension system on the Cabrio, Bravos, and Oasis washing machines is about as simple as it gets. The outer tub is suspended on four spring-loaded suspension rods. This design enables the washer tub to absorb a great deal of vibration and shock by using the weight of the tub as a counterbalance.
What is the drain pump on a Whirlpool Cabrio?
The Drain pump of a Whirlpool Cabrio, Maytag Bravos, or Kenmore Oasis washing machine is essentially the same as the recirculation pump except it’s purpose is to remove dirty wash water from the washing machine’s tub and send it packing down stream. Because the water level is being monitored by the pressure sensor built into the washing machine’s control board, if the washer takes to long to drain an “ Ld ” meaning “Long Drain” error code will appear on the washer’s display. Another common drain related error code is “ Sd ” meaning “Suds Detection” (For more information about troubleshooting these error codes click on the code link) Like all washing machines it is important to check your pockets for loose change and put smaller items such as baby socks and lingerie into a mesh laundry bag to keep them from finding their way into the drain pump or recirculation pump.
What is a control board on a washing machine?
All electronically controlled washing machines use a control board to process commands entered into the user interface and send the proper amount of electricity to a particular washer component at the correct time to perform some function, such as opening a particular water valve solenoid, operating the motor, energizing the recirculation pump, drain pump or lid lock. If the washing machine were a body the control board is the brain behind all of the washer’s operations.
What is the inner basket on a Whirlpool washing machine?
Most washing machines have an inner basket that is directly attached to the drive system at all times.
How to save energy by not connecting to hot water line?
If you want to save energy by not connecting to the hot water line (or only have access to a cold water line if connected in a garage, etc.), purchase a “Y-connector” and an extra inlet hose to connect the hoses to both sides of the water valve.
How long does it take for a washer to reset?
If the unit is unplugged before turning off the power, the washer will go into a reset mode, which will take approximately 10 minutes to complete. You may hear the pump running, and the door will unlock after about 10 minutes.
How to clean a clogged water hose?
Check the inlet screens on the back of the water inlet valve. If they appear to be clogged, scrub thoroughly with a brush (an old toothbrush works great) and mild soap and water.
What can restrict water flow in a hose?
Check for any kinks in inlet hoses, which can restrict water flow.
Can a washer run with only one incoming water?
The washer will not properly operate with only one incoming source of water. The water valve inside the machine needs to have the “pressure” from both attached hoses in order for the washer to complete the cycle. If a cold water wash is selected, the washer is designed to add hot water to keep the temperature optimal for cold wash performance. ...
How to save energy by not connecting to hot water line?
If you want to save energy by not connecting to the hot water line (or only have access to a cold water line if connected in a garage, etc.), purchase a “Y-connector” and an extra inlet hose to connect the hoses to both sides of the water valve.
How long does it take for a washer to reset?
If the unit is unplugged before turning off the power, the washer will go into a reset mode, which will take approximately 10 minutes to complete. You may hear the pump running, and the door will unlock after about 10 minutes.
How to clean a clogged water hose?
Check the inlet screens on the back of the water inlet valve. If they appear to be clogged, scrub thoroughly with a brush (an old toothbrush works great) and mild soap and water.
What can restrict water flow in a hose?
Check for any kinks in inlet hoses, which can restrict water flow.
Can a washer run with only one incoming water?
The washer will not properly operate with only one incoming source of water. The water valve inside the machine needs to have the “pressure” from both attached hoses in order for the washer to complete the cycle. If a cold water wash is selected, the washer is designed to add hot water to keep the temperature optimal for cold wash performance. ...