Here are some possibilities:
- A 2-to-1 mixture of warm water and white vinegar** .** Spray this over the affected area, or spread it with a brush, and let it soak in. ...
- A 3 percent hydrogen peroxide solution** .** Spray it on, let it sit for a few minutes and blot dry.
- Peroxide, dish soap and baking soda. ...
How do I Clean my hardwood floors?
Remove carpet, padding, and all debris from the floor. Make sure nails, staples, and other debris are all off the floor. Vacuum well and ensure that no dust, wood splinters, and other remnants are left on the floor. 2. Thoroughly wash the hardwood floor. I used the Bona hardwood floor cleaner system.
How do you remove carpet glue from plywood?
Scrape the carpet glue off the plywood subfloor by using a 10-inch putty knife. Wipe the subfloor down with a wet sponge. Always open windows in the room so you have adequate ventilation when removing carpet glue from floors. Heating the glue and using solvents can result in some toxic fumes.
How do you restore hardwood floors under carpet?
Restoring hardwood floors under carpet – in 4 easy steps 1. Remove carpet, padding, and all debris from the floor. 2. Thoroughly wash the hardwood floor. 3. Apply Weiman High Traffic Hardwood Floor Polish & Restorer. 4. Apply a final coat of Weiman High Traffic Hardwood Floor Polish & Restorer.
How do you clean urine stains from plywood?
If urine stains have set into the plywood subfloor, you can treat it in the same way you would treat any subfloor. Note that some wood reacts and swells on contact with any liquid – an issue that might already exist as a result of urine. Enzyme cleaners often recommend you spot-test small areas of wood before treating a larger area.
How do you clean wood under carpet?
Use a hardwood floor cleaner, such as Bona floor cleaner, that you can spray directly on the floor or fill a bucket with warm water and 1/4 cup dish soap. Sweep very dirty floors with a bristle broom to collect any large debris in a dustpan.
How do you clean dirty plywood?
For instance, if you mix 1 cup of water, ¼ cup of white vinegar and 2 teaspoon mineral oil or coconut oil, you have got yourself a mild plywood cleaning agent! You can also mix a gentle soap-based cleaner with water and use the diluted solution in combination with a microfiber cloth to wipe dirty surfaces clean.
How do you deodorize plywood?
Treating Urine in a Plywood SubfloorApply an enzymatic pet odor remover. You can choose one of several products, including Nature's Miracle, Anti-Icky-Poo or Zero Odor. ... Allow the cleaner at least 24 hours to soak into the wood. ... Let the wood dry out completely. ... Apply a subfloor sealer.
How do you get rid of mold on a plywood subfloor?
Treat exposed molded subflooring with a mixture of 1 cup of borax and 1 gallon of water or an EPA-registered mold removal product. Spray the solution on the moldy plywood. You can also soak affected subflooring with a brush broom. Wait 10 minutes, scrub the area, and repeat the process two more times.
How do you clean unsealed plywood?
Soapy Solution A squirt or two of natural dish soap mixed into a bucket of lukewarm water serves as a mild cleaner for untreated, unfinished wood.
Can you use bleach on plywood?
If you want to lighten the color of plywood, there's a bleach for the job, and if you want to remove stains, there's a bleach for that, too. In fact, you can choose from two different bleaches for removing stains. Bleaching plywood isn't much different from bleaching solid wood, with ...
How do you remove urine smell from subfloor?
Spray 3 percent hydrogen peroxide on the spot and let sit for a few minutes. Blot dry with a clean cloth. For a stronger solution, mix 3 percent hydrogen peroxide with a squirt of dish soap and a sprinkle of baking soda.
How do you get the smell of urine out of a subfloor?
For fresh urine stains on the subfloor, hydrogen peroxide can help remove the odor. Pour it over the wood, and let it soak in for a few hours before blotting it with a towel. A combination of liquid dish soap and baking soda can help absorb some of the urine.
What do you use to clean a subfloor?
Start by thoroughly vacuuming or sweeping the particle board to remove any loose dust and dirt. Next, combine either one part vinegar with one part water or 1 part bleach with 3 parts water in the bucket. Either of these solutions will eliminate the smell and the bleach will also disinfect.
How do I know if my subfloor has mold?
Even if you have access to professional moisture detection meters, subfloor mold can be difficult to discover. Perhaps the easiest means of detecting a subfloor mold problem are seeing discoloration on vinyl flooring, warping or distortion in areas of flooring, or the presence of malodors.
How do you treat mildew under carpet?
White vinegar for light to medium mold growth. Put some in a spray bottle, then apply generously. Unlike baking soda, white vinegar doesn't need to sit for long – just for a few minutes. After, scrub until it is absorbed, then dry the area with a hairdryer or fan.
Does moldy subfloor need to be replaced?
The moldy subfloor must also be removed and replaced. Particular care must be taken when cutting into moldy wood because the process sends mold spores flying into the air. Moldy wood removed from the subfloor should be enclosed in double plastic bags before it is carried through the house.
How do you clean a dirty subfloor?
Combine 1 cup of warm water, 1/4 cup of mild dishwashing soap and 1/3 cup of white vinegar in a spray bottle. Shake well, spray it onto one spot of the subfloor, wipe it off with a cloth and check the results. If it worked, you can then mix a larger amount in a bucket and clean the subfloor with a sponge.
How do you take care of plywood?
Plywood furniture should be dusted using a soft, dry microfiber cloth. Never use rough, abrasive or wired cleaning pads on your plywood furniture to avoid scratches. Dust at least once a week or as often as necessary. Dirt, oil and grime collect in the crevices and joints of your furniture over time.
How do you clean plywood kitchen cabinets?
0:121:55Housekeeping Tips : How to Clean Wood Kitchen Cabinets - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt just takes a little splash of vinegar. And you can use a little Bowl you know or a big bucketMoreIt just takes a little splash of vinegar. And you can use a little Bowl you know or a big bucket depending on how many cabinets you have obviously fill it most the way with water.
How do you pressure wash plywood?
0:241:55Wood Cleaning Tips: How To Clean Wood Using Pressure WasherYouTubeStart of suggested clipEnd of suggested clipStart come through keep your wand at the same height. So that you maintain pressure even across theMoreStart come through keep your wand at the same height. So that you maintain pressure even across the whole board lock the deck. And you can pretty much do the whole deck like that.
How to sand a wood floor with a palm sander?
Sand the floor with an orbital flooring sander and 80-grit sandpaper to flatten the wood grain and blend the filler. Vacuum the floor, then sand again with 100-grit paper. Use a palm sander to sand in corners and edges where the large machine doesn't reach.
How to protect polyurethane paint?
Protect the paint with at least one coat of clear polyurethane finish. Apply the finish with a pad applicator or paintbrush. To get the smoothest finish, apply two or more coats, screening each undercoat with a 150- grit screen when it dries.
Can you paint a plywood floor and pull up carpet?
How to Pull Up Carpet and Paint the Plywood Floor. A time eventually comes when another cleaning won't salvage the carpet, and you have to take it up. That leaves you with a bare subfloor and a number of expensive flooring options. Although it sounds like a slap-dash solution, painting the subfloor can actually be a viable alternative.
Can you paint subfloor?
Although it sounds like a slap-dash solution, painting the subfloor can actually be a viable alternative. Flooring paint wears as well as most floor coverings, and you have control over the color.
How to keep wood floors from getting too dry?
To avoid getting too much moisture on the wood it is necessary to work in small areas and use the smallest amount of water possible. Dip just the tips of a stiff broom in the water and brush it along the floor. When you finish with a small area, dry up any remaining moisture with a dry mop or old towels.
How to dry up wood finish?
When you finish with a small area, dry up any remaining moisture with a dry mop or old towels. Remove the moisture as quickly as possible to avoid any damage to the wood.
How to clean particle board?
Start by thoroughly vacuuming or sweeping the particle board to remove any loose dust and dirt.
Do you need to wait for paint to dry before installing carpet?
Allow the paint to dry completely before installing new carpet.
How long does it take for mineral spirits to soak in carpet glue?
Wait 30 minutes for the mineral spirits to soak through and loosen up the carpet glue.
Can you use carpet glue on plywood?
Carpet glue can either be a traditional type of glue or tar-based, and you'll need to identify which type you have. Traditional glue has a yellow appearance, while tar-based glue is brown or tan. The same removal methods can be used either on plywood subfloors or hardwood floors.
How do I clean a hardwood floor?
Make sure nails, staples, and other debris are all off the floor. Vacuum well and ensure that no dust, wood splinters, and other remnants are left on the floor. 2. Thoroughly wash the hardwood floor. I used the Bona hardwood floor cleaner system.
What did the hardwood floor look like after carpeting was removed?
The hardwood floor looked dull after the carpet, padding, staples & tack strips were removed.
What is the best tool to pull staples from a carpet?
Hammer – for pulling nails from the floor. Pliers – for pulling staples holding carpet pad. Masking tape or duct tape – helps for securing rolls of carpet & padding for removal. Safety glasses – protect your eyes when pulling staples and nails from the floor.
Does Weiman restore hardwood floors?
The Weiman product made restoring hardwood floors under carpet a much easier process than I had feared it would be. According to the bottle, it “is specifically formulated to instantly rejuvenate hardwood floors. Micro-filling technology removes scratches, while a protective, scratch resistent layer prevents new scratches from forming.”
Can you restore hardwood floors that have been hidden under carpet for years?
Have you ever wondered how hard it is to restore hardwood floors that have been hidden under carpet for years? Turns out it can be pretty easy!
Is Weiman polish safe for hardwood floors?
An important note about the Weiman polish and restorer product is that it is safe for all hardwood floor finishes. Our hardwood floor did not appear to have a polyurethane finish. (We still need to figure out exactly what was used to finish our floors in the 1960s – varnish or wax.)
How long does it take for a wood floor to dry out?
Allow the cleaner at least 24 hours to soak into the wood. It's a good idea to cover the treated area with plastic to control evaporation. Let the wood dry out completely. It's best to wait for an extra 24 to 48 hours after you remove the plastic. Apply a subfloor sealer.
How to get rid of a smelly subfloor?
Once this happens, the only way to get rid of the smell is to remove and replace the floor covering and treat the subfloor. Urine in a plywood subfloor or a concrete one can usually be neutralized, and if you seal the affected area before installing new flooring, that should be the end of your odor problem.
What is the best floor sealer for pet urine?
Apply a subfloor sealer. The best floor sealer for pet urine is a stain-blocking primer, such as Kilz 3 Premium Interior/Exterior primer, which not only blocks stains and odors but also contains a mildewcide. Any all-purpose oil- or water-based stain-blocking primer will work, especially if you apply two or three coats.
How to get rid of urine smell in concrete?
Spray the cleaner or spread it over the affected area with a scrub brush, using a generous amount to ensure it soaks in. Cover the treated area with plastic to prevent evaporation and wait for 24 hours before removing the plastic and letting the area dry out.
How to get rid of cat urine smell in wood?
Some products work better for cat urine than dog urine, and vice versa, so read the label to make sure you get the right product. Allow the cleaner at least 24 hours to soak into the wood.
What happens if you shine a black light on plywood?
After you've removed the floor covering, you want to make sure to identify the entire stained area. The most strongly affected areas will be discolored, but if you shine a black light on the surrounding plywood, you'll probably detect the telltale florescent shine of uric acid in other places.
What is the best way to clean pet urine?
Enzymatic cleaners work best for neutralizing pet urine, but some household cleaners also work, especially if the urine problem isn't severe. Here are some possibilities: A 2-to-1 mixture of warm water and white vinegar** .**. Spray this over the affected area, or spread it with a brush, and let it soak in. Blot dry after a few minutes.
What to do if you have a wood subfloor?
If you have minor damage to your wood subfloor from pets or spills, it's a good idea to brush on some primer/sealer over these areas to seal in odors and protect your new carpet. For concrete floors, you might consider a concrete sealer to protect the surface from moisture and wear. Advertisement.
How do I fix baseboards?
This is the easiest time to get your baseboards fixed up. Clean painted or sealed baseboards with a mixture of all-purpose cleaner and a little bleach. Make sure the cloth is well wrung out and doesn't drip heavily onto your subfloor. Use a good semi-gloss or gloss paint to freshen up your baseboards and make them easy to clean. If you have problems with pet odor or damage, consider priming/sealing the baseboards before painting.
Can you use old tack strips on wood?
Old tack strips can be re-used, but if the wood is rotten or stained, use a pry bar to pull it up. If you have a professional carpet installer coming in, they probably won't be as picky about the condition of the tack strips as you are, so don't count on them to replace the damaged pieces with new ones.
Can you use a vacuum to clean tile floors?
You can use a broom and dust pan or shop vac to clean your floors of dirt, debris, and old staples. Do NOT use a house vacuum, as chunks of plaster, wood chips, or staples could irreparably damage it. If the tile floor is especially dirty or sticky, feel free to mop with an all-purpose cleaner, but make sure the floor is completely dry ...
Can you mop tile before laying carpet?
If the tile floor is especially dirty or sticky, feel free to mop with an all-purpose cleaner, but make sure the floor is completely dry before laying down new carpet. Moisture can ruin your new carpet and padding.
Can you pull up old carpet padding?
Pulling up old carpet padding will leave a mess of staples still embedded in the floor. They'll be easily spotted by the tufts of padding that are trapped underneath. You want the smoothest possible surface for your new carpeting, so it's worth the extra time and effort to pull these staples out.
What is the best way to get rid of set in stains on flooring?
Absorbing – or wicking – liquid from flooring is the best weapon against set-in stains.
How do I get rid of a stain on my subfloor?
Once you have exposed the stain on the subfloor, it’s time to treat it. You could try a DIY solution at this stage, such as a vinegar and detergent solution. However, if the stain is so troublesome that you had to pull up some flooring to treat it, I would suggest going straight for the “big guns.”.
How to get rid of urine smell under foundation?
Fortunately, this is just another type of foundation, and the treatment approach is very similar. You’ve got to get the stained area soaked with an organic cleaner to rid the stain and urine odor under your finished layer.
Can you use dog urine remover on wood floors?
That depends. Old stains can often be treated with dog urine remover such as an enzyme cleaner; this product can penetrate beyond your carpet, tile, and wood flooring. Deep-set stains and spots that have been defiled by your pet repeatedly might require you to remove some flooring and attack the spot beneath.
Can urine be soaked in subfloor?
Spoilers ahead! Any urine accidents on the aforementioned floors can result in a nasty problem- urine soaked into your subflooring .
Do stains soak up wood?
But do stains ever soak down past the carpet, wood, or laminate? The icky truth is yes; they can.
Can you remove tile without breaking it?
It is difficult to remove tile without breaking it. A tile remover shank can be helpful in the process. Hopefully, you have a few spare tiles lying around the house. If not, it might be time to make a trip to the home improvement store. It’s a little bit easier to do the same with wood flooring without ruining it.
