- Heat n Glo fireplace’s base consists of the drop-down panel. The first step in remote pairing is to open the fireplace’s drop-down panel.
- The next step is to locate the remote control module. The remote control applications are primarily designed in the fireplace’s remote control module. ...
- Move the Remote Control’s Sliding Switch. The remote consists of a small black sliding switch. ...
- Get something like a paper clip or like that. The paper clip will help to produce the remote module’s beep.
- Locate the Learn Button. The small black sliding switch’s below consists of a small hole. This small hole is known as the “LEARN” button. ...
- In this step, you must use the previously collected paper clip. Locate the Learn button or small hole and push the paperclip in it. ...
- The next step is to check whether the remote is flashing the Green Led light or not. ...
- Now, after seeing the green LED light flashing, the next step is crucial. ...
- Hearing the Two beep sound is important because it indicates the success of the above whole process. ...
How do I install a gas fireplace remote control?
The installation of your remote is fairly simple and only requires a few materials. Take your receiver, which will get the signals from the remote control, and connect it to the gas valve. Open the vent to the fireplace and there should be a connector spot where you can simply plug the receiver into the valve.
How do I Sync my fireplace remote to my receiver box?
Immediately after you hear the beeping noise, press the On or Mode button on your remote control. If your remote has both buttons, press the On button. At this point, you should hear a beeping noise again, and your fireplace should immediately turn on, indicating your fireplace remote control has been synced with the receiver box.
Where is the receiver box on a gas fireplace?
Most often your receiver box will be located within the control cavity of your fireplace, like it is here. Check to make sure the wires are secured tightly to the terminals.
How do I reset the code on my fireplace remote?
If your remote has both buttons, press the On button. At this point, you should hear a beeping noise again, and your fireplace should immediately turn on, indicating your fireplace remote control has been synced with the receiver box. Clearing memory offers an additional option for resetting remote codes.
How do you pair a remote to a fireplace?
0:421:20How to Relearn or Re-Pair RC/100/200/300 Fireplace Remote ...YouTubeStart of suggested clipEnd of suggested clipButton wake up the remote. Press the gray bar on the top of the remote. And then hit the pairing.MoreButton wake up the remote. Press the gray bar on the top of the remote. And then hit the pairing. Button the double beep tells you that everything is ready to go.
How do you relearn a fireplace remote?
1:232:41Troubleshooting a Skytech Fireplace Remote Control - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if your fireplace doesn't turn on another step to take would be to reset the codes in the memoryMoreSo if your fireplace doesn't turn on another step to take would be to reset the codes in the memory within the receiver box to do so press and hold the learn button for 15 seconds.
Why is my remote not working for my fireplace?
1) Batteries do not have enough power or are installed incorrectly. 2) Misunderstanding on how the remote features operate the fireplace. 3) The slide switch on the receiver is not in the correct position. 4) The remote hand-held transmitter has not had the “learn” function activated to the receiver.
How do I sync my gas log remote?
0:411:44Syncing a gas log remote control. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what we're going to do is push the learn button in at around the same time we're going to go toMoreAnd what we're going to do is push the learn button in at around the same time we're going to go to our handheld and then hit the on button.
How do you reset a remote control?
For Android TVs released in 2015 or later, symptoms may improve by updating the software of the remote control....Reset the remote control.Open the battery compartment cover and remove the batteries.Press and hold the Power button for three seconds.Insert the batteries again and close the battery compartment cover.
How do you turn on an electric fireplace without the remote?
The fireplace must be plugged in at the wall and the wall socket turned on. The power button on the electric fireplace must be switched on. The flame effect switch must be turned on (if separate to the main power switch). The flame dial can then be used to control brightness of the flames.
How does a fireplace remote work?
Remote control gas fires work with the use of a battery operated or mains connected control valve, which responds to your battery powered remote control. You don't have to use the remote control to operate some fires – they also come with standard controls on the appliance itself.
How do I pair my heat and Glo remote?
0:571:50Heat & Glo RC300 remote pairing instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe power button on the remote handset. The module then double beep confirming the pairing has beenMoreThe power button on the remote handset. The module then double beep confirming the pairing has been successful.
How do you reprogram a fire genie remote?
0:041:21Regency Firegenie Remote Control Operation - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the on/off switch to turn the remote on the remote. Will operate in the last mode it was inMoreUse the on/off switch to turn the remote on the remote. Will operate in the last mode it was in manual auto or program mode to set the time in the remote. Hold down the time key for two seconds.
Get Help with Your Fireplace Remote Installation
Fireplace remote controls can offer plenty of different features to control your gas fireplace. From simple on/off control to programmable thermostats, there's no question these remote controls can simplify your favorite appliance. However, fireplaces remote controls require a small amount of setup before use.
Speak to an Expert
If you still have questions after watching these videos, our team is here to help. Contact us to speak with a product specialist today!
What is a gas fireplace remote?
A gas fireplace remote control will allow you to easily start your gas fireplace with the minimal effort of clicking a button. The installation of your remote is fairly simple and only requires a few materials.
How to get power to receiver?
Once the receiver is connected to the valve, you will to supply power to the receiver. Plug the receiver into the nearest open outlet in order to get electricity to the receiver.
Do you need a fireplace thermostat to use an outlet?
Those who are not close enough to a wall outlet should look into using a fireplace thermostat. It will usually require a couple batteries and you will no longer need to use an outlet.
Why won't my remote work on my fireplace?
There are many reasons a remote control could stop functioning correctly. Before troubleshooting your remote, however, make sure you can still ignite your fireplace at the unit itself. Using the receiver box of your fireplace remote control system, move the switch to the “On” position. If the fireplace ignites, we can safely assume the problem lies within your remote or receiver box. If the fireplace fails to ignite using this method, the problem is likely within the fireplace itself and you may need to contact a fireplace service technician to troubleshoot the problem further.
How long does a fireplace remote last?
Like all small electrical components, a fireplace remote control may fail after years of regular use. Typically, you can expect a remote to last eight to 10 years, but many last much longer than that. If your remote is in this age range, you may be due for a replacement.
What is a thermostatic remote control?
Thermostatic Remote Controls: Thermostatic remote controls can control your fireplace based on temperature to help regulate the feel of a room.
How long is Skytech remote warranty?
If the purchase date was more than one year ago, consult the product manual for extended warranty information. Skytech remotes, for example, are warrantied for five years.
What is a wall mount remote control?
However, these units are mounted to the wall like a light switch. These are great if you want the convenience of remote control without needing to worry about losing a transmitter.
What is a smart home controller?
Smart Home Controllers: Smart home automation is a relatively new addition to the hearth space. These units allow you to control your fireplace using either Bluetooth or WiFi—a great option if your home already features smart home tech.
Can you supply a remote to a fireplace?
Unfortunately, many fireplaces from big box stores feature valves with proprietary designs. For this reason, it is often difficult to supply a remote capable of replicating all features found on the fireplace.
1. Locate the Receiver Box
Most often your receiver box will be located within the control cavity of your fireplace, like it is here. Check to make sure the wires are secured tightly to the terminals.
2. Check the Batteries
If your receiver box is battery operated, make sure the batteries are new and have a full charge; do so for the remote control too. It's possible that if you haven't replaced the batteries recently, corrosion may have formed. This could prevent the system from operating, and you'll need to replace them.
3a. Perform the Learn Function
The remote control communicates to the receiver box via radio frequency signal, so it's common for the signal to be interrupted. Luckily, it's very easy to resync them. Begin by locating the Learn button on the receiver box. Press and release the button quickly; you should hear a beeping noise.
3b. Continue Learn Function Process
Immediately after you hear the beeping noise, press the On or Mode button on your remote control. If your remote has both buttons, press the On button. At this point, you should hear a beeping noise again, and your fireplace should immediately turn on, indicating your fireplace remote control has been synced with the receiver box.
4. Reset the Memory
If you perform steps 1-3 and you still can't get your remote to work, you may need to reset the memory. Each receiver box has a small internal memory to store the signals from the remote control, and it's possible for this memory to fill up and not allow the learn function to work.
5. Remote Still Not Working?
These troubleshooting steps should solve any issue you're having with a Skytech fireplace remote control. If you're still not able to get your remote to work, feel free to contact us with any further trouble. Our product experts are available Monday through Friday 9 a.m. to 5 p.m. Central Time to field your questions.
