Connecting the Wires with a Strip Connector
- 1 Choose a strip connector that works with your LED lights. The main types of connectors are clip-on and fold-over ones. ...
- 2 Slide the strip into the connector. ...
- 3 Align the wires with the correct color on the strip. ...
- 4 Close the connector depending on the specific type you’re using. ...
How to set up LED strip lights?
Installing your strip lights
- Measure your space. Measure the area to determine the total length of lightstrip you’ll need. ...
- Test your lightstrips. Once you’ve purchased the right number of lightstrips and extensions, test them to make sure they’re working correctly before installation.
- Test your look. ...
How do I connect LED strip lights to one another?
- Line the wires up so that the colors are matched correctly according to the labels on the light strip.
- It only takes a small dot of solder to attach the wires securely to the strip.
- Avoid heating the wires for too long, or you might ruin the LED lights.
- With your wires connected to the light strip, your lights are ready to be lit.
How to install LED strip lighting?
Step-by-step installation for LED strip lights
- Buy your LED strip lights
- Cut to length
- Connect to power
How do I install LED light strips?
Third Part: The Actual Steps of LED Strip Light Installation.
- Test supplies to be installed. Before installation, it is recommended testing the supplies including LED strips and controllers. ...
- Prepare mounting surfaces. Well-prepared mounting surfaces will facilitate fast and secure mounting of strip lights. ...
- Measure length. ...
- How to cut LED strip lights? ...
- How to connect LED strip lights together?
How to connect two LED strips together?
What is flexible LED light strip?
What wattage do you need for LED lights?
What is solder free LED wire connector?
How to calculate wattage of LED ribbon lights?
How to calculate the power draw of LED lights?
Why use wire connectors?
See 2 more
Can LED strip lights be joined together?
Two LED strips can be connected together by using strip connectors. There are two types of connectors; clip-on and fold over. The connector that you choose to use will depend on the type of strip lights that you are connecting.
Do you need connectors for LED strip lights?
The Single-Color LED strips need a 2 pin LED extension cable. The cables themselves finish off at either end with common 2.1mm size barrel plug adapters that are used with all single-color strips and dimming controllers.
How do you use a 4 pin connector LED strip?
Connecting LED light strips with these connectors is very simple:1: Open clip on each side.2: Slid the 10mm LED light strip inside the clip underneath the two contact prongs.3: Make sure the side of the strip aligns with the "+ -" polarity.4: Close the wire clip.
How do you use a LED quick connector?
Be sure not to pull too hard and damage the quick connector. Peel back the tape of the 3M adhesive approximately 1/4 of an inch. Insert Strip Light into connector, check the wire polarity (red wire to positive) copper dots should not be visible. With connector between your 4 fingers, squeeze the black piece closed.
How do you connect LED strips without soldering or connectors?
How to connect LED Tape without soldering – LED Tape connectors1: This is the Tape to starter lead connector for single colour. ... 2: Cut the LED Tape along the cut line with a pair of scissors. ... 3: Now take your Tape to starter lead connector and your new piece of cut LED Tape.4: Open the Connector.More items...•
How do you hook up two LED strips without connectors?
1:143:13How to Connect 2 LED Light Strips Together (without special cables or ...YouTubeStart of suggested clipEnd of suggested clipYou know connectors on the other light strip. And then you're gonna use the sticky. Thing. YeahMoreYou know connectors on the other light strip. And then you're gonna use the sticky. Thing. Yeah whatever that's called to stick it down and do that for both sides.
Do LED strip connectors work?
Soldereless strip connectors do NOT make a permanent electrical connection with the strip light. While the teeth on the clasp do an okay job keeping the strip in place, movement is still possible - and if there's a lot of it it's likely that the contact pads can move away from the contact prongs and lose connection.
Why are my LED connectors not working?
With the connector box open, we need to check and make sure that LED strip's oval or circular copper pads are properly lined up with the connector's silver pins. If you can see that they aren't aligned right, gently move the strip back and forth until the strips light up properly, this usually fixes connection issues!
How many LED strips can you connect together?
Vetco recommends, as a general rule, not to connect more than three complete strips end-to-end without adding in extra, higher gauge power wire or additional power supply units down the line.
What is a quick connector for LED lights?
Quick Connectors allow you to use cut pieces of RGBW LED Strip without having to solder on leads. This Quick connector comes with a 6" lead of 20-5 wire for RGBW LED Strip lighting. Features. Easily utilize cut pieces of RGBW LED Strips. No need to solder on leads to RGBW LED Strip.
How do you connect two LED strips to one power source?
You Simply have to install one end of your strip to the hippo buckle connector to connect two strips together. The buckle on the connector keeps the strips in place once installed. you can use these connectors to connect two strips together or even connect your LED strip to the power supply.
Can you cut LED light strips and reconnect them?
A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.
How do LED strips connect to power supply?
For this, all you need to do is connect the led strips to the ends of your led splitter and then plug in your female connector to the male connector on your power supply. This will ensure that power is distributed evenly and the lights are working as they should.
Do LED strip connectors work?
Soldereless strip connectors do NOT make a permanent electrical connection with the strip light. While the teeth on the clasp do an okay job keeping the strip in place, movement is still possible - and if there's a lot of it it's likely that the contact pads can move away from the contact prongs and lose connection.
What are connectors for LED lights?
Two main types of connections for both 2, and 4 Pin LED Strip Connectors are strip-to-strip and strip-to-wire. Using strip-to-strip connections allows both strips' ends to join. It also keeps the electrical current flowing to turn the lights on and off when desired.
How do strip lights plug in?
Plug-in Adapter – Plug straight into your wall to power your LED strip lights. Hardwire Power Supplies – Directly wire in between your line voltage wiring and your LED Strips.
How to connect LED lights to a strip?
Learn more... To connect your LED strip lights, you can either use a connector for easy attachment, or you can solder the wires to the strip, which carries more current and creates a more stable connection. Whichever method you choose, make sure you cut your light strip along the designated cut points to ensure your lights will work if necessary. ...
How to align wires on a light strip?
Align the wires with the correct color on the strip. The dots on either side of the cut line are the dots you use to align the wires. The light strip should have letters telling you which colored wire goes where, making it easy to align them correctly.
Why won't my strip lights have connectors?
Some larger strip lights won't have connectors available because they can't handle infinite current, meaning you'll need to solder the strip if you make a cut.
How to make wires easier to attach to a strip?
This is called pre-tinning the wires. Use the soldering iron to add a little bit of solder to each end of however many wires you’re using. This helps makes the wires easier to attach to the strip. It doesn’t take a lot of solder—it should barely be visible on the wire.
What is the difference between a clip on and a fold over strip light?
If you’re not sure which strip connector to choose, look at the recommended strip connectors for the specific brand and type of strip light you’re using. A clip-on connector will slide right into the strip, while a fold-over connector will be a bit bulkier and have a flap that attaches over the strip. ...
What connectors do LED lights use?
Choose a strip connector that works with your LED lights. The main types of connectors are clip-on and fold-over ones. When you choose a connector, be sure it works with the wires you’ll be using according to your type of strip lights—a different connector may be necessary for a monochrome strip light than for a RGB strip light with multiple colors. Refer to the packaging that came with your strip lights for details about the specific kind of light you purchased.
How to solder a wire strip?
Add solder to each of the contact points on the strip. The contact points, which are right next to the cut line, are the dots where you’ll place the wire to be attached. Add a small dot of solder onto each of the contact points to prepare the points for the wire.
How to connect a strip light to a connector?
Gently push each section of the strip light into the connector piece. Use the small clamps on the connector to snap the strip lights in place. Be sure both sides of the strip light is facing the correct way. The polarity needs to be correct for voltage to run through. Plug your strip lights in and check for light on both sides of the connection.
What type of connectors do you use for strip lights?
This will usually represent the style of strip light. For example, you may have an RGB, RGBW or just a 12V warm white . These variations work with 4 pin, 5 pin and 2 pin connectors .
What is gapless LED strip light?
Using gapless pin connectors allows you to make a continuous run of LED light without a large gap appearing. Each brand and style of LED strip light may use different pin quantities. Most are 4 pin connectors, but you may encounter 2 pin and 5 pin as well. Another note to pay attention to is the width of your strip light.
How to connect two lights together?
Here's a Quick Step-by-Step Guide to Connect Multiple Strip Lights 1 Unplug your strip lights before starting. 2 Get your measurements right. As the saying goes, “measure twice, cut once.” 3 Decide if you need a straight connector or an 90 degree angled connector. 4 Use standard craft scissors to cut along pre-determined cut line of the copper section. This copper section is on your strip light spaced every few inches. 5 Each section of strip light should have equal amounts of copper section left over. This is needed to make your connector pins work. 6 Have your small plastic gapless or jumper connection ready and peel back any adhesive backing to allow for a clean connection. 7 Gently push each section of the strip light into the connector piece. 8 Use the small clamps on the connector to snap the strip lights in place. 9 Be sure both sides of the strip light is facing the correct way. The polarity needs to be correct for voltage to run through. 10 Plug your strip lights in and check for light on both sides of the connection. 11 If you have no light on the new section of strip light, check the polarity and reverse the strip light if needed.
What to do if you have no light on the new section of strip light?
If you have no light on the new section of strip light, check the polarity and reverse the strip light if needed.
How often do you have copper markings on LED strip lights?
Your LED strip light roll or section will have copper section markings every few inches within the strip.
How to cut copper strips?
Use standard craft scissors to cut along pre-determined cut line of the copper section. This copper section is on your strip light spaced every few inches.
What is LED strip connector?
The LED strip connectors in this guide will help you to: LED strip connectors provide a quick-connect solution that lets people avoid having to use a solder iron. If you do have a solder iron, or want to buy one, then we recommend soldering as the most reliable option.
What type of connector is used for LED strip lights?
There are two different connection types for the EZ Click tight connectors for LED strip lights. The 2-pin LED strip connectors are used for single color strips. They only require a two-port connection as they simply need one positive and one negative connection.
How to get wires to click down?
Once the wires are sitting above the grooves click the cap down . For the wire side it is best to use a set of pliers to help click the connector down all the way, it takes some force!
What is a 4 pin RGB connector?
The 4 pin RGB connectors have one common positive line as well as a connection for each of the Red, Green and Blue color LEDs so that they can all be controlled separately to make an assortment of different colors. There are both 2 and 4 pin versions of the following LED strip connectors:
How many pins are in LED strip connector?
There are both 2 and 4 pin versions of the following LED strip connectors:
How many feet can you run with two strips?
Have two shorter strips that you want to chain together to make a longer strip? As long as you are staying within the maximum run limitations (32.8 ft. for High Density and 16.4 ft. for Standard Density) you can do that easily with one strip to strip connector!
How much heat shrink should I use for a wet connector?
If you need to seal your connections because you are in a wet area then I would recommend putting some heat shrink over the whole connector. We use ½ inch heat shrink to do so here that works.
What color is the LED strip side?
Then, determine the type of connection used on the "LED Strip Side" (shaded blue ). Detailed instructions for determining the type are below.
What is the pad on LED strip?
Almost all LED strips have copper pads, labeled (+) and (-) on the actual strip itself. This is where the electrical inputs must ultimately be fed through. Depending on your particular situation, you will likely encounter three different possible scenarios.
What happens if you overvoltage an LED strip?
Undervoltage to the LED strip will result in the LED strip operating at lower brightness or no light output at all, and overvoltage will burn out your LEDs. Secondly, make sure that the power supply capacity is sufficient for the length of LED strip being used.
Can you solder copper pads without wires?
Converting Copper Pads to Wires. If you're cutting the LED strip into shorter segments, you will very likely end up with copper pads without any wires. Many tutorials and instructional videos will immediately suggest soldering wires onto those copper pads to achieve an electrical connection. But, soldering is not for everyone.
Can you connect more than one LED strip to a single power supply?
If you're trying to connect more than one LED strip segment to a single power supply, you may suddenly realize that you could connect the first segment to the second segment in "series" or connect to two segments independently to the same power supply. Generally, "series" will be more straightforward, but may lead to some issues with voltage drop.
Can you cut LED strips into shorter segments?
If you do cut the LED strip into shorter segments, you will end up with at least one segment that falls under the first scenario.
Can you convert copper pads on LED strips into wires?
Just like this, in a matter of seconds, you can convert copper pads on the end of an LED strip segment into wires.
How to Cut LED Strip Lights
Prior to cutting confirm if the strip you purchased can be cut: because some strips once cut can become unstableDon’t. Proceed to ensure that you completely turn off the power supply. It is exceedingly risky to cut a 24v RGB led strip that is attached to a power source directly.
How to Fix Cut LED Strip Lights
It is important to note that once you cut the LED strip you bought the part that remains will not be functional. If you wish to rejoin them after cutting, you’ll need to utilize an additional 4 pin connection. However, if you cut and connect the light strip incorrectly, it may cause the light strip to cease operating properly.
How to Fix Cut LED Strip Lights
Strip connections are the most convenient choice since they do not require any tools. Begin by removing the clear plastic covering the copper pads with a knife. Then, just slide the strip into the connection, making sure that the components match.
Which Type of LED Strip Lights Can Be Cut
Whatever kind of LED strip light you have got, you’ll be sure of 1 thing: you’ll be able to cut it to the length you wish. Throughout your LED strip, there’ll be straight or dotted black or white lines indicating where you will cut. Because the circuits are isolated here, it’s easy to chop on these lines.
Conclusion
So there you’ve got it. LED strip lights could also be adjusted to match the wants of any installation, large or small.
How to connect two LED strips together?
You can connect multiple strips together to light larger spaces and unusual nooks and crannies. There are two ways to connect LED tapes with each other: 1. Clipping. The easiest way to connect two LED strips together is to use a LED light strip connecting clip.
What is flexible LED light strip?
They provide a lot of variety in terms of color and size. Flexible LED light strips help you light unusual places where traditional sources of lighting simply cannot reach.
What wattage do you need for LED lights?
For example, if your LED strip wattage requirement was 19W , you will need a power source that has a minimum output of 23W (19/0.8). This will keep your power supply from getting overheated. Once you have the minimum wattage requirement down, choose one of three options to for supplying power to your ribbon lights:
What is solder free LED wire connector?
c). Solder-Free LED Wire Connector: Your project might require your LED light strips to go around a corner or an unusual shape. That is where the solder-free LED wire connectors come in handy. These wire connectors have clips on both ends so you can use them to connect two LED light strips with each other. They are great for extending the length of your LED light strips.
How to calculate wattage of LED ribbon lights?
If you’re using the same LED light tape for your entire project then multiply the length of the entire strip you want to power from a single source with the wattage per meter. This will give you the power capacity of your power source. If you’re using different types of LED ribbon lights then calculate the wattage requirement for each of them and add it all. This will give you an idea of how much juice they need to work.
How to calculate the power draw of LED lights?
This can be done easily by multiplying the length of the strip by the wattage per meter of the strip. For example, if you have a 3.8m long strip with 5W/m power draw, you will need a transformer with a capacity of at least 19W to power it. You can find the power draw information for each LED strip on its packaging or on the manufacturer’s website.
Why use wire connectors?
This is because these wires don’t have LEDs mounted on them. They can only be used to extend the length of the strips. You can connect both single color and RGB LED tape lights with each other.
