Here is the work that needs to be done:
- Cut into a 1" incoming PEX pipe - going into the manifold.
- Drill couple holes to run the lines to/fro water softerner that is next to the manifold.
- Attach the needed elbow connector to the incoming pipes.
- Run the line to the water softern. About 2 ft
- Run another line from the water softener to the PEX manifold. About 2 ft.
Full Answer
How do I hook up a water softener to my plumbing?
Branch off cold water lines to outdoor faucets before running the cold water through the water softening system. The plumbing hookups on a water softener can be confusing, but we'll show you how the connections should be made. You don't have to be a plumber to connect a water softener. We make it easy to understand even for a beginning DIYer.
Do water softener lines run to water heater?
Once the water leaves the softener, it should branch into two lines: a cold line that runs to interior fixtures and faucets, and a line that feeds the water heater. The outgoing line from the water heater then runs to interior fixtures and faucets that dispense hot water.
How does a water softener work in a house?
The main supply line to the rest of the house continues on to the softener. Once the water leaves the softener, it should branch into two lines: a cold line that runs to interior fixtures and faucets, and a line that feeds the water heater. The outgoing line from the water heater then runs to interior fixtures and faucets that dispense hot water.
How do I bypass my water softener?
In addition to those lines, there should be a soft water bypass loop (shown in the photo) with a valve you can open to bypass the softener if you need to disconnect it temporarily without disturbing the water supply to the house.
How far to run line from PEX manifold?
How to get a quote for a plumber?
Can you solder a pex connector to a flexible hose?
Can I rent a PEX unit?
Can you connect a PEX softner to a PEX softner?
Can you use PEX for water softener?
Answer: You are BEST to simply connect into the PEX and PEX over to the softener itself, on the back of the softner will be a inlet and outlet by-pass valve to which you will need to connect into… I suggest doing all this in PEX with the proper crimp rings to avoid leaks.
Can you use SharkBite for water softener?
SharkBite Water Softener Connectors will decrease the amount of time and effort needed to install a Water Softener in your home and are the fastest way to complete your project. 3/4 in. Pipe Insertion Depth = 1-1/8 in.
How do water softeners connect to pipes?
3:165:12How to Install a Whole-House Water Softener | Ask This Old HouseYouTubeStart of suggested clipEnd of suggested clipWe make a connection at the softener. And also at the brine. Tank. Connect the drain line to theMoreWe make a connection at the softener. And also at the brine. Tank. Connect the drain line to the drain elbow and we secure that with a hose. Clamp.
How do I connect my PEX supply line?
6:2021:43PEX Pipe Installation - ALL Connections To Fittings In A ...YouTubeStart of suggested clipEnd of suggested clipYou don't want to have it too close or too far apart eighth inches about right and what i like to doMoreYou don't want to have it too close or too far apart eighth inches about right and what i like to do is take a pair of needle nose. Go over that crimp ring and crimp it on tight.
Why do they say not to use SharkBite?
A SharkBite fitting contains a rubber O-ring, which is not best for permanent connections. We don't recommend using a SharkBite fitting outside because sunlight can dry out the rubber O-ring and cause it to crack or split.
Is PEX and SharkBite the same?
Push-fit or stab-in plumbing fittings are a popular type of PEX and copper fitting; SharkBite is a popular brand name of push-fit fittings used with pressure booster pumps. With a bit of effort, the pipe pushes into the fitting and is held in place by tiny teeth.
Where should a water softener drain into?
By code Water Softeners must be emptied into a laundry sink, floor drain, sump hole or properly trapped special outlet, preserving an air gap of at least two times the diameter of the drain line, but in no case less than 1-1/2" above the top of the receptacle used.
Do you need a separate drinking water tap with a water softener?
Many people choose to have a separate hard water tap to provide unsoftened water for drinking. But there are no legal, health or safety requirements to do this. If you choose to install a Harvey water softener, we can fit a hard water drinking tap as standard, so you can choose your preferred source of drinking water.
Where do I tie my water softener?
The ideal location for a water softener is on level ground, near the water's point of entry into the house. If your home uses well water, the entry point is generally next to the pressure tank. If your home uses city water, it's usually next to the water meter.
Where should you not use PEX?
You can't install PEX in high heat areas like near recessed lighting. This also means you can't connect PEX directly to a hot water heater, but you can use a connecting material to do this. PEX is semi-permeable, which means liquid can enter the pipe. When it comes to safety, PEX isn't antibacterial.
Why do PEX fittings fail?
Common Causes of PEX Pipe Failures PEX piping has a maximum bend radius, which can lead to stress on the pipe caused by improper installation. In addition, extreme bends and kinks place a very high local stress on the wall of the pipe, making it more susceptible to oxidative degradation.
Can you use SharkBite on PEX?
SharkBite brass push-to-connect fittings are compatible with PEX, copper, CPVC and HDPE pipe. They come with a PEX stiffener pre-loaded into the fitting for PEX and HDPE, and the stiffener doesn't need to be removed for copper or CPVC applications.
Do plumbers recommend SharkBite fittings?
Many professional plumbing technicians think that SharkBite fittings and other sort of push-fit fittings need to only be utilized as an emergency situation, temporary repair, and not for any enclosed or permanent plumbing system. There is a growing group of DIYers who would disagree.
What type of pipe is used for water softener?
You may have copper, PVC, CPVC, steel or PEX plumbing. Each of these plumbing types may require different materials and different tools for installation. A drain is necessary for the regeneration or recharge process.
What can SharkBite fittings be used on?
SharkBite brass push-to-connect fittings can be installed in wet lines and provide the versatility to work with PEX, copper, CPVC, PE-RT and HDPE pipe.
How long will SharkBite last?
How long do SharkBite fittings last? SharkBite fittings last a long time. In fact, SharkBite warrants the fittings for 25 years when used with SharkBite tubing.
Installing Water Softener With Pex
Clean Water Made Easy Fleck 7000 Neutralizer Installation … Clean Water Made Easy will still have acidic water flowing through it. We recommend PEX or PVC pipe up to the neutralizer and then copper after it, if you have copper plumbing. enough to warrant a water softener, which removes calcium hardness. … View Full Source
Water softener install with PEX for novice : Plumbing - reddit
I was leaning towards Fleck 5600SXT which seems to be the standard. I wanted demand based for sure and I prefer electronic vs mechanical. I see your point about getting them serviced, in that I would need a regular plumber and it so happens I have a good one.
How far to run line from PEX manifold?
Run another line from the water softener to the PEX manifold. About 2 ft.
How to get a quote for a plumber?
Call plumbers and ask for a quote. Note if you call them Sunday evening because your spouse is yelling that they have no water because you don’t know what you are doing and you need them out right away you can expect to pay conciderably more.
Can you solder a pex connector to a flexible hose?
I don’t know off-hand of any pex connectors that transition directly to flexible hose. If you can’t find any you may have solder a short peice of copper with pex connection on one end and a hose connector on the other.
Can I rent a PEX unit?
Answer: Well I am not aware of being able to rent them but if you know a plumber friend he might let you use it. If you set the unit up and cut all the PEX to the correct specs you may simply be able to call a local plumber and ask them what their hourly charge is and say you need them to make some connections…no more than an 1 hour fee…
Can you connect a PEX softner to a PEX softner?
Answer: You are BEST to simply connect into the PEX and PEX over to the softener itself, on the back of the softner will be a inlet and outlet by-pass valve to which you will need to connect into…I suggest doing all this in PEX with the proper crimp rings to avoid leaks.
Do you have to be a plumber to connect a water softener?
The plumbing hookups on a water softener can be confusing, but we'll show you how the connections should be made. You don't have to be a plumber to connect a water softener.
Can you branch off a water softener?
The piping around a water softener can be confusing when attempting to learn how to install a water softener. A cold water branch before the water softener doesn’t necessarily indicate a problem. It’s standard procedure to branch off one cold water line to supply outdoor hose connections (and sometimes another to the kitchen sink and refrigerator icemaker if you don’t want to drink softened water).
How far to run line from PEX manifold?
Run another line from the water softener to the PEX manifold. About 2 ft.
How to get a quote for a plumber?
Call plumbers and ask for a quote. Note if you call them Sunday evening because your spouse is yelling that they have no water because you don’t know what you are doing and you need them out right away you can expect to pay conciderably more.
Can you solder a pex connector to a flexible hose?
I don’t know off-hand of any pex connectors that transition directly to flexible hose. If you can’t find any you may have solder a short peice of copper with pex connection on one end and a hose connector on the other.
Can I rent a PEX unit?
Answer: Well I am not aware of being able to rent them but if you know a plumber friend he might let you use it. If you set the unit up and cut all the PEX to the correct specs you may simply be able to call a local plumber and ask them what their hourly charge is and say you need them to make some connections…no more than an 1 hour fee…
Can you connect a PEX softner to a PEX softner?
Answer: You are BEST to simply connect into the PEX and PEX over to the softener itself, on the back of the softner will be a inlet and outlet by-pass valve to which you will need to connect into…I suggest doing all this in PEX with the proper crimp rings to avoid leaks.
