There are also fittings with screw collars which are used to clamp the pipe in place and are simply unscrewed to release. To make a water tight joint using SPEEDFIT® the first job is to cut your plastic pipe to the correct length and ensure the end you will be inserting in to the fitting is square.
What fittings are used with Speedfit pipe?
K: Pipe clips which should be used every 500mm with speedfit pipe There are many other types of fittings but these are the ones which are used the most. For every fitting available in copper compression or Yorkshire, there is a SPEEDFIT® equivalent. The table at the foot of the page shows some of the other fittings available.
How do I cut Speedfit® pipe?
Never use a hacksaw to cut SPEEDFIT® pipe, always use a pipe cutter shown below. If you push a pipe with a rough end into one of these fitting the burrs may damage the O ring which will lead to a leak Do not push your fingers into any fitting as the teeth may cut you
How do I Disconnect a fitting?
Disconnecting a fitting is as easy, if not easier, than connecting up. Each of the two types has a slightly different process: Standard Fittings: Simply push the collet down squarely until it touches the main body of the fitting. This will release the gripping mechanism and allow you to gently pull the pipe out
How do you make a water tight joint with Speedfit?
To make a water tight joint using SPEEDFIT® the first job is to cut your plastic pipe to the correct length and ensure the end you will be inserting in to the fitting is square. As stated, don’t be tempted to use a hacksaw, use a pair of plastic pipe cutters (as seen below).
Do you need to use pipe inserts with Speedfit fittings?
The simple answer is yes, always use an insert when installing Speedfit pipes as it supports the shape of the pipe.
How do I lock my Speedfit fittings?
3:265:25The Speedfit Science – How our fittings work - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo. The twist and lock screw cap holds the collet legs blocking the pipe in its position as theMoreSo. The twist and lock screw cap holds the collet legs blocking the pipe in its position as the stainless steel teeth dig into the pipe surface to hold it tightly.
How do you use Speedfit fittings on copper pipe?
0:062:07How to use speedfit/push fit fittings with copper pipe/tube - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine up your copper tube now all you plumbers who are watching this firstly. If you know how to doMoreLine up your copper tube now all you plumbers who are watching this firstly. If you know how to do it you should be watching it secondly there are loads of people who don't have a clue.
How do you connect plastic water lines?
0:009:37How to join pex (plastic pipe) five different ways. Plumbing Tips!YouTubeStart of suggested clipEnd of suggested clipSystem it's simply a stainless steel clamp. And we'll just take a piece of plastic pipe we slide ourMoreSystem it's simply a stainless steel clamp. And we'll just take a piece of plastic pipe we slide our fitting. In put the clamp. Over. This tool hook the up the teeth in there squeeze down on.
How do you stop a push fit joint from leaking?
3:088:14How to Fix Leaking Quick-Connect Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd make a little mark right at about 3/4 of an inch on the tubing itself. And then when you put itMoreAnd make a little mark right at about 3/4 of an inch on the tubing itself. And then when you put it into the fitting. The tubing should go in far enough that that line disappears under the collet.
How long do Speedfit fittings last?
speedfit = 25 years, hep20 = 50 years.
How do I connect plastic pipe to copper pipe?
Compression adapters make the best joints between copper and PVC. You can connect PVC or CPVC to copper in several ways. One common method is to solder a female threaded fitting onto the copper pipe, screw in a male threaded plastic fitting and finish up by gluing plastic pipe to the plastic fitting.
Can you fit Speedfit to copper pipe?
Speedfit fittings can be connected onto chromium plated copper pipe if the chromium plating is completely removed to the full depth of the fitting. To ensure maximum grip, the fitting of a collet clip is recommended.
How do you fit a push fitting to copper pipe?
0:422:55How to install a push fit plumbing fitting - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo always use a pair of pipe cutters like a pipe slice to shamp for the edge. And that's that partMoreSo always use a pair of pipe cutters like a pipe slice to shamp for the edge. And that's that part there if you used an axe or it needs a square cut that is then difficult to push the fitting into. So
How do you connect two water lines together?
The easiest way to connect faucet water supply lines together is by using a compression fitting. Measure your line diameters carefully and purchase the same size compression fitting to join them.
How do you join plastic tubing?
0:432:29How to Glue and Join PVC Plastic Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipI like to use the felt tip marker I not only give myself index marks but I number the joints too soMoreI like to use the felt tip marker I not only give myself index marks but I number the joints too so it all goes back together without any confusion prime the pipe in the fitting.
How do you install plastic pipe fittings?
0:322:58How to use push fit pipe. Push fit plastic plumbing tutorial. JG SpeedfitYouTubeStart of suggested clipEnd of suggested clipSo you just literally push the insert into the pipe like that take your fitting this one is an elbowMoreSo you just literally push the insert into the pipe like that take your fitting this one is an elbow push. This in as far as it will go.
How do I turn off JG Speedfit?
0:202:01Renovate; How to remove a Speedfit push-fit plumbing fitting. - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat you might find is insert gets stuck in there. Now you can pull it out with a pair pliers orMoreWhat you might find is insert gets stuck in there. Now you can pull it out with a pair pliers or just untwist the whole thing.
How do you use speedfit isolation valve?
7:519:31How to fit an isolation valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want me to start link a push for its isolation bulb it's much easier all you need to do isMoreIf you want me to start link a push for its isolation bulb it's much easier all you need to do is push that onto the end of the pipe.
How do you use John Guest fittings?
0:482:07How to use quick connect fittings (John Guest type) - YouTubeYouTubeStart of suggested clipEnd of suggested clipMaking a connection hold the fitting firmly in your hand and insert the tubing where you will feelMoreMaking a connection hold the fitting firmly in your hand and insert the tubing where you will feel some initial resistance. Then push in the tubing. Until it stops gently.
How do I use JG Speedfit reducer?
Simply push the push-fit fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. To demount the connection, unlock the nut by hand and push the collet towards the body of the push-fit fitting and pull the pipe to release.