Yes speedfit/Hep/ and all pushfit plumbing fittings can be used directly onto copper. Not chrome plated though as it slips. Good advise on not sweating a joint too near a pushfit fitting as you will damage the O ring.
How to use Speedfit on copper pipe?
I use speedfit to copper all the time when I am doing simple jobs to cut down on the time on the job and to make it less expensive for the customer. 1 minute, cut pipe to length, dry fit pipe to check for fit, if it fits, turn locking rings, your done.
Can you use copper olives with Speedfit fittings?
Use ONLY copper olives with Speedfit not brass and never over tighten them. Don't use plastic pipe with a combination of cheap ball type valves and ceramic disc taps, they will eventually blow off. The Supaseal inserts with the o rings are for plastic pipe and Speedfit fittings.
Why choose Speedfit® fittings?
Benefits of SPEEDFIT® Fittings Because the pipes and fittings are plastic there is no scale build up and the elasticity of the pipe greatly reduces the likelihood of pipes bursting in freezing conditions although they should certainly still be lagged.
Do I need an insert when installing Speedfit pipes?
The simple answer is yes, always use an insert when installing Speedfit pipes as it supports the shape of the pipe. We have two types of insert – the ‘STS’, or Superseal for plastic to plastic, and the ‘TSM’ for plastic to compression. The ‘ STS has an extra O-Ring, which helps to reduce the risk of leaks due to side load.
Can you solder to close a plastic fitting?
Does plumbersmate use inserts?
Can you use a pipe slicer on copper pipe?
How do you connect push fit plumbing to copper?
0:281:22copper pushfit fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just push it straight into the fitting. And then do the same on the other side. And then whenMoreAnd just push it straight into the fitting. And then do the same on the other side. And then when you've pushed it in that's it the joints being made.
How do I connect plastic pipe to copper pipe?
2:0411:52How to Join Plastic and Copper Pipes | Plumbing Guide for BeginnersYouTubeStart of suggested clipEnd of suggested clipAnd what we need to do is slide the nut over our copper pipe. And then slide the olive over theMoreAnd what we need to do is slide the nut over our copper pipe. And then slide the olive over the copper pipe as well then we need to get the body of that compression fitting.
Can you use plastic push fittings on copper pipe?
Originally developed to be used with plastic pipe systems, push-fit joints are a good way of joining copper pipes too (although they can't be used with stainless steel or chrome-plated copper pipe). It's important that your pipe ends are cut cleanly, so make sure you use a pipe cutter rather than a hacksaw.
How do I connect my speedfit?
0:262:58How to use push fit pipe. Push fit plastic plumbing tutorial. JG SpeedfitYouTubeStart of suggested clipEnd of suggested clipSo you just literally push the insert into the pipe like that take your fitting this one is an elbowMoreSo you just literally push the insert into the pipe like that take your fitting this one is an elbow push. This in as far as it will go.
Can you put copper pipe and PVC together?
If you try to connect them together, you'll likely damage or break the copper pipe. To prevent this from happening, you should use a special adapter that allows you to connect PVC pipes to copper pipes. The most common type of adapter for connecting PVC pipes to copper pipes is called an elbow connector.
What can I use to connect copper to PVC?
0:061:01Connecting PVC to PEX and Copper - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe standard way of connecting pecks or copper pipe to PVC is by using threaded adapters.MoreThe standard way of connecting pecks or copper pipe to PVC is by using threaded adapters.
Does copper pipe need an insert with speedfit?
No you do not use pipe inserts whilst using push fit on copper, but make sure you when using plastic barrier pipe, the best ones to use are the super seals.
Can I use copper with push fit?
Push fit fittings and pipes, like copper, can safely withstand heat and pressure so they're suitable for water and heating systems. Many joints are pressure tested to standards in excess of those usually required in domestic situations – 10 bar (100 psi) is common.
Do you need pipe inserts for push fit?
Pipe inserts are required on push fit and compression fittings when using plastic pipe. The inserts vary in size from one manufacturer to another ,so you should use the inserts relative to the pipe brand.
What is a speedfit connector?
Speedfit fittings are a push fit jointing system which is suitable for most plumbing applications, including hot and cold water and central heating installations including pressurised and combi systems.
Do you have to put inserts with Speedfit fittings?
The simple answer is yes, always use an insert when installing Speedfit pipes as it supports the shape of the pipe.
How do you connect PVC to copper pipe without welding?
A compression fitting is the best way to connect PVC to the copper pipe without welding. Another option is a push-fit fitting, also called a shark bite fitting.
How do you connect PVC to copper pipe without welding?
A compression fitting is the best way to connect PVC to the copper pipe without welding. Another option is a push-fit fitting, also called a shark bite fitting.
Can you connect plastic pipe to metal pipe?
Connecting the Two Pipes To successfully connect plastic and metal pipes, you need threaded connections. The plastic male thread must connect to the metal female thread. If you try to connect it the opposite way – a plastic female to metal male – then the connection will ultimately break or leak.
How do you connect ABS pipe to copper pipe?
0:455:02Quick Tip for Connecting to Old Copper Drain Line - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're able to tighten them up and that's how you adopt from inch-and-a-half copper over 2 inch andMoreYou're able to tighten them up and that's how you adopt from inch-and-a-half copper over 2 inch and a half abs PVC cast iron something like that this really helps with older home remodels.
Do SharkBite fittings work on PVC?
SharkBite PEX fittings make it easy to transition between pipe types during repairs. Fast, efficient and reliable, our transition fittings are compatible with Polybutylene, PEX, PVC, CPVC, PE-RT and SDR-9 HDPE, and are approved for behind-the-wall installation as well as burial.
Can you solder to close a plastic fitting?
another thing to consider is never solder to close to a plastic fitting as the heat can damage the o ring's and shorten there lifespan.
Does plumbersmate use inserts?
as plumbersmate has never used inserts before it might be worth mentioning there are two one has an external o ring used mainly in heating it has a double seal in a sense and the second is just hard plastic more use for compression fittings if you use the ring seal in the wrong place it has very little bearing inside the fitting
Can you use a pipe slicer on copper pipe?
Yes you can use it with out inserts on copper pipe, and as said before as long as you use pipe slicer instead of an hacksaw. Speed-fit is better sometimes, when you have little access to run the pipes for example under the floor boards, or inside cavity wall. It saves you time and effort. But you have to be careful not to scratch or damage the outside of the plastic pipe, as it could leak if the rubber ring of the fitting sits on top of damaged (scratched) pipe.
How long to cut a pipe to length?
1 minute, cut pipe to length, dry fit pipe to check for fit, if it fits, turn locking rings, your done.
What happens if a pipe freezes?
As for frost and freezing pipes, if the water in the pipe freezes to form a plug and there is nowhere for the expanding water to go it will expand until it fully freezes and if there is no room, it will carry on expanding the pressure will rise and the point of least resistance will go first! So no matter what fittings you have, in the worst case scenario something will split, copper pipe, soldered fitting, compression fitting, push fit fitting, flexible hose tap connector, I've seen them all failed due to freezing at one time or other.
Can you push a speed fit off copper pipe?
Yes, but in the past under mains pressure I have seen speed fits get pushed off of copper pipe but that was when the pipe froze so ok inside but not outside.
Can you use a hacksaw to cut pipe?
No but make sure you use pipe cutters and not a hacksaw or you will destroy the seals in the fitting.
Can you use push fit on copper pipe?
No you do not use pipe inserts whilst using push fit on copper, but make sure you when using plastic barrier pipe, the best ones to use are the super seals.
How do SPEEDFIT® Fittings Work?
This images above shows just how advanced the technology is with these fittings.
Why use Speedfit fittings?
Because the pipes and fittings are plastic there is no scale build up and the elasticity of the pipe greatly reduces the likelihood of pipes bursting in freezing conditions although they should certainly still be lagged . The pipes are metal free and non toxic and being able to use long lengths ...
How to disconnect a pipe?
Disconnecting a fitting is as easy, if not easier, than connecting up. Each of the two types has a slightly different process: 1 Standard Fittings: Simply push the collet down squarely until it touches the main body of the fitting. This will release the gripping mechanism and allow you to gently pull the pipe out 2 Twist Lock Fittings: Unscrew the cap so that it is loose and then push down on the collet with equal force all the way around to that it depresses squarely until it touches the body of the fitting and then gently pull the pipe out
What is a pipe insert?
A: A short length of pipe showing a pipe insert at each end. Pipe inserts must be used every time a joint is effected. The insert gives additional strength to the end of the pipe as it is clamped between the teeth of the fittings. The image above shows how a pipe insert works (titled: "Insert for pipe ends")
What happens if you push a pipe with a rough end?
If you push a pipe with a rough end into one of these fitting the burrs may damage the O ring which will lead to a leak. Do not use damaged or scuff pipes. Do not push your fingers into any fitting as the teeth may cut you. Use pipe cutters when cutting plastic pipe.
How to make a water tight joint?
To make a water tight joint using SPEEDFIT® the first job is to cut your plastic pipe to the correct length and ensure the end you will be inserting in to the fitting is square. As stated, don’t be tempted to use a hacksaw, use a pair of plastic pipe cutters (as seen below).
What is a speedfit?
SPEEDFIT® pipes are ideal for retro fitting bathroom items such as concealed showers as the pipes can be hidden much more easily than copper.
Can you solder to close a plastic fitting?
another thing to consider is never solder to close to a plastic fitting as the heat can damage the o ring's and shorten there lifespan.
Does plumbersmate use inserts?
as plumbersmate has never used inserts before it might be worth mentioning there are two one has an external o ring used mainly in heating it has a double seal in a sense and the second is just hard plastic more use for compression fittings if you use the ring seal in the wrong place it has very little bearing inside the fitting
Can you use a pipe slicer on copper pipe?
Yes you can use it with out inserts on copper pipe, and as said before as long as you use pipe slicer instead of an hacksaw. Speed-fit is better sometimes, when you have little access to run the pipes for example under the floor boards, or inside cavity wall. It saves you time and effort. But you have to be careful not to scratch or damage the outside of the plastic pipe, as it could leak if the rubber ring of the fitting sits on top of damaged (scratched) pipe.
