After getting the adapters, you can screw them to your hose connectors, then join the hoses with the following steps:
- Retract the spring-loaded ring on the female connector.
- Slot in the male connector into the female one and push it in.
- Release the ring on the female connector to secure the two halves together.
How do you put a straw in a water bottle?
The straight cylinder piece fits on to the bottom of the straw with the straw going in via the larger end. 3. The other more cone-shaped part is the top of the straw and goes on the other end. 4. Pop the straw inside the bottle, open the lid and make sure the straw goes through the hole.
Can you connect two garden hoses together?
Yes, you can connect two garden hoses together as long as they share the same diameter. Hoses of the same size can be joined by fitting the male connector of one hose to the female connector of the other. Before joining the hoses together, ensure that the back end of the main hose is connected to a water source but not running.
How do you make a vortex out of a soda bottle?
These amazing connectors screw onto two plastic soda bottles (you can buy new ones from E.I., Item number BOT-600 and allow students and teachers to create a water vortex. Or, connect two small soda bottles and make a sand timer.
Can you assemble the 99p water bottle on TikTok?
TikTok can make anything go viral in seconds and the 99p water bottle was no exception to the rule. Yet some people really can’t work out how to assemble it. Don’t worry, we’ve got you.
How do you join two plastic bottles together?
0:503:58How To Make a Huge Water Rocket by Splicing Bottles Together!YouTubeStart of suggested clipEnd of suggested clipTake one of your cup bottles and briefly dip it into the hot water so the heat will shrink it enoughMoreTake one of your cup bottles and briefly dip it into the hot water so the heat will shrink it enough to fit inside the other bottle.
How do you make a bottle connector?
0:1010:10DIY Tornado Tube GLOWS in the Dark! TKOR Dishes On How To Make ...YouTubeStart of suggested clipEnd of suggested clipWhile the center of the hole has air flowing up through it into the bottle on the top. Because airMoreWhile the center of the hole has air flowing up through it into the bottle on the top. Because air is able to flow into the top bottle as the water drains into the lower bottle.
What is a bottle connector?
Product Description These amazing connectors screw onto two plastic soda bottles (you can buy new ones from E.I., Item number BOT-600 and allow students and teachers to create a water vortex. Or, connect two small soda bottles and make a sand timer.
What is a vortex connector?
The Vortex Bottle Connector is a plastic adapter fitted so that two plastic soda bottles can be held together in order to create a vortex in the top bottle. It works by flipping and then spinning the top bottle so that air begins to replace the water in the top bottle, forming a vortex shape.
How do you make a water tornado with two bottles?
STEPS TO TAKE:Fill your first bottle 3/4ths the way full.Feel free to add food coloring or glitter which will make your tornado easier to see.Add the washer to the top of the first bottle.Add the washer to the top of the first bottle.Tape the two bottles together. ... Flip the bottle upside now and give it a spin.
How do you make a water tornado?
Instructions:Fill your container about ¾ full with clean water.Add a squirt of dish soap, as well as your glitter or food coloring, if desired.Seal the container tightly.Move the bottle rapidly in a circular motion. After a few seconds, you should see the water begin swirling. Stop, and watch your tornado!
How do you make a vortex water bottle?
Try This:Fill one of the bottles about 2/3 full with water, place the washer on the mouth of this bottle.Next invert the second bottle onto the washer and tape them together firmly.Turn the two bottles over so the full one is on top. ... Set the bottles down and watch the vortex form.More items...
What is a twister tube?
A tornado tube is a fun toy which allows you to create a mini-tornado. You connect two pop bottles together. One of them you fill with water. You then orient the bottles so that the water filled bottle is on top and the empty bottle is at the bottom.
How does a tornado tube work?
0:573:13Tornado Tube - Cool Science Experiment - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you look at it the air comes up the water comes down the air comes up and so you have it's an oldMoreIf you look at it the air comes up the water comes down the air comes up and so you have it's an old dishwasher. Trick see how that works ah i.
How does a water vortex work?
When the water level and pressure drop low enough, the water surface can hold back the water and stop the flow completely. If you spin the bottles around a few times, the water in the upper bottle starts rotating. As the water drains into the lower bottle, a vortex forms.
What makes a vortex?
A vortex is a rotating region of fluid such as, for example, a tornado or a whirlpool. These vortices are generally created at a moving boundary due to the shear resulting from the no slip condition, but can also result from thermal circulation.
What is a vortex and how it is formed?
In the dynamics of fluid, a vortex is fluid that revolves around the axis line. This fluid might be curved or straight. Vortices form from stirred fluids: they might be observed in smoke rings, whirlpools, in the wake of a boat or the winds around a tornado or dust devil.
How do you make a water bottle holder?
2:257:54How to Make: Water Bottle Straps for Around $1 - 3 Easy DesignsYouTubeStart of suggested clipEnd of suggested clipMake a loop feed. It through then. You want to tighten this up that's about as much of a loop as youMoreMake a loop feed. It through then. You want to tighten this up that's about as much of a loop as you want just enough get over the opening of the carabiner.
How do you make a tap out of a bottle?
0:582:22How to with Zoe: Water Bottle Tap - YouTubeYouTubeStart of suggested clipEnd of suggested clipUnscrew. Your flat lid. And place your thumb over the hole while filling your bottle up to the topMoreUnscrew. Your flat lid. And place your thumb over the hole while filling your bottle up to the top with water. Make sure to securely. Position your thumb over the tiny hole.
How do you make a vortex bottle?
0:082:55Tornado Tube - Vortex in a Bottle - YouTubeYouTubeStart of suggested clipEnd of suggested clipAction so you're ready so you're going to swirl like this swirl. And then you pull your hand out ofMoreAction so you're ready so you're going to swirl like this swirl. And then you pull your hand out of the way. And look at that vortex. There it is and you're winning.
How do you make a paracord water bottle holder?
2:044:19Paracord Water Bottle Holder | HOW TO - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd press down on the cords to lock them. In. Place. Now for the beaded version we're going to takeMoreAnd press down on the cords to lock them. In. Place. Now for the beaded version we're going to take a piece of micro cord or any thinner diameter cord for that matter and loop it around the 550 loop.
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping.
Product description
Demonstrate a vortex in your classroom! Show that in order for water to flow down, air must flow up. These amazing connectors screw onto two plastic soda bottles (you can buy new ones from E.I., Item number BOT-600 and allow students and teachers to create a water vortex. Or, connect two small soda bottles and make a sand timer. Only one Tube!
Product details
There was a problem filtering reviews right now. Please try again later.
How to secure plastic to a wall?
Other methods include drilling or poking small holes in the plastic, then using epoxy or a similar structural adhesive to glue the sides , allowing the adhesive to enter the holes, flow around the other side , and form what are essentially rivets that mechanically secure the two surfaces.
Can you heat hot glue off glass?
Heating it outside of a traditional glue gun will create nore undesirable fumes than usual. You could peel hot glue off of glass, metal or some other hard, smooth surface. Next you could conceivably cut it up into small pieces, discard any contaminated bits, heat them and pour them into a mold of the correct size in order to recast it. This would allow it to be used in a glue gun again, but given the low cost of the material it seems like a lot of effort to go to.
Do cyanoacrylates stick to plastic?
Cyanoacrylates stick well to a variety of plastics if they are clean, dry and free of oil or grease, which is true for almost any adhesive. Because of how water-thin the glue is, the parts must mate well or you must use a gel formulation which fills gaps.
