How to Start the Chainsaw (Step-by-Step)
- Step 1: Stabilize the Chainsaw ...
- Step 2: Engage the Chain Brake ...
- Step 3: Turn the Chainsaw On and Open Up the Choke ...
- Step 4: Prime the Fuel ...
- Step 5: Pull the Starting Cord a Few Times ...
- Step 6: Close the Choke ...
- Step 7: Let the Chainsaw Idle ...
- Step 8: Close the Choke ...
How to start a gas chainsaw?
For your safety, you must first of all, set its chain brake, because, the chain of a gas-powered chainsaw will rotate around its bar as soon as you start the engine. The engine of gas-powered chainsaw will start smoothly if you give it a burst of fuel. For this, you will have to close the choke to block the flow of fresh air into the engine.
How do you start a chainsaw with the choke on?
Turn the chainsaw on/off switch to the on position. Open up the choke by moving the knob/lever to the cold start (or fully open) position. The choke regulates the air/fuel mixture that goes to the engine. Press the fuel primer bulb three to five times or until the bulb stiffens and you can see fuel in it.
How do you lubricate a chainsaw crank?
In almost all gas chainsaw engines, the crank is lubricated by the oil mixed in the fuel. Unlike four-stroke engines, which house the lubricant in the crankcase, these two-stroke engines utilize fuel premixed with the lube oil in an appropriate ratio (typically 50:1). The fuel to oil mixture is also known as a premix.
How do you crank a depressed chainsaw without an interlock?
After a few minutes, you can often simply pull the crank cord again with everything on, including the throttle pressed in along with its interlock. Cranking a depressed chainsaw without a working interlock is difficult without using a drop start (which is dangerous.) Have a second person pull the cord if someone is around.
How to fix a chainsaw that is not working?
Why is my chainsaw stalled?
How many pulls does a choke need to start?
How to keep a saw clean?
Can you start a chainsaw with ethanol?
Can you prime a chainsaw if it's flooded?
See 3 more
About this website
How do you crank up a chainsaw?
0:421:54Chainsaw Basics: How to Start a Gas Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition your choke is pulled out and you've pressed the purge valve four to five times to prime theMorePosition your choke is pulled out and you've pressed the purge valve four to five times to prime the engine.
How do you use a chainsaw step by step?
1:303:13Chainsaw Basics: How to Safely Use a Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour right hand will be on the rear handle. Which controls your throttle. So before you start yourMoreYour right hand will be on the rear handle. Which controls your throttle. So before you start your cut. You want to throttle up the chainsaw place it lightly on the wood.
What do you pull to start a chainsaw?
Activate the choke and (on certain models) press the decompression control. Pull the starter handle until the engine fires. Push the choke (half-throttle) and pull again until the saw starts. Accelerate (rev) so that the engine idles and then release the chain brake.
Do you start a chainsaw with the brake on?
Step 1 of 15: Before starting your chain saw, the chain brake should be activated by pushing it forward (see picture). Step 2 of 15: Always remove the bar cover before starting your chain saw.
What should you not do with a chainsaw?
Do not operate a chainsaw above shoulder height or above ground level, such as in a tree or off a ladder, unless qualified and experienced to do so. Always have someone within calling distance - never work alone while using a chainsaw. Never operate your chainsaw under the influence of alcohol or drugs.
How do you use a chainsaw on a small tree?
0:492:34How to Cut a Tree with a Chainsaw Safely | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen create a notch on the side of the tree facing the direction you want the tree to fall make theMoreThen create a notch on the side of the tree facing the direction you want the tree to fall make the top cut first at a 45 degree angle.
Can you start a chainsaw without a pull cord?
There are four different ways to start a chainsaw easier or without pulling the cord: you can also start your chainsaw with a drill. Spring-assisted starting system. Capacitor discharge ignition (CDI) or Memory power ignition (MPI)
Why will my chainsaw not start?
A spark plug might be defective and needs to be replaced. If your chainsaw has a defective spark plug, it cannot create an electrical current to ignite the system. Remove the spark plug and inspect if it is dirty, cracked, eroded, or damaged. There may also be a heavy carbon buildup or a burned-up electrode.
What does the choke do on a chainsaw?
The choke position increases the richness of the air and fuel mixture the carburetor sprays into the cylinder. With the master control lever in the choke position, the flow of fuel into the engine increases and the flow of air decreases.
How do you release the brake on a chainsaw?
0:111:57How To Reset Husqvarna Chain Brake | Fix Stuck or ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen push the chain break all the way to the front take the clutch cover and line it over the bridgeMoreThen push the chain break all the way to the front take the clutch cover and line it over the bridge over the chainsaw. And just push it in. And that reset the chain. Break.
Should you let a chainsaw warm up?
Warm starting a chainsaw boils down to doing so when the engine is hot. While the procedure is the same as cold starting, skip everything to do with the choke. In case of a difficult start, we recommend warm starting the engine at half-throttle.
Do all chainsaws have a brake?
All chainsaws must have chain brakes that comply with ISO 6535:2008 Portable chain-saws — Chain brake performance.
How do you cut logs with a chainsaw?
1:433:05How to cut logs safely with a chainsaw - Which? guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake. Sure you grip the handle. And the throttle fully with your right hand even if you're left-MoreMake. Sure you grip the handle. And the throttle fully with your right hand even if you're left-handed. Keep the saw horizontal. And make sure you cut in the middle of the guide.
How do you cut firewood with a chainsaw?
1:236:06How to split wood with a CHAINSAW - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo as soon as you dig into the wood. You're. So low so you start bringing the chain down into theMoreSo as soon as you dig into the wood. You're. So low so you start bringing the chain down into the wood okay. Right at the center points okay obviously if you guys while you could follow a crack.
What part of the chainsaw do you cut with?
The guide bar is the most important part of the chain saw when it comes to cutting wood, so when there is a wrong alignment in terms of the direction of the chainsaw blade, then there will be a lot of problems.
What does the choke do on a chainsaw?
The choke position increases the richness of the air and fuel mixture the carburetor sprays into the cylinder. With the master control lever in the choke position, the flow of fuel into the engine increases and the flow of air decreases.
Chainsaw Won’t Start? 10 Most Common Reasons with Solutions
4. Air filters should be checked. In the event of a dirty or clogged air filter, the engine won’t get the air needed for combustion, and as a result, the chainsaw won’t start.. Solution: Clean out or replace the air filter.. Prevention: Regular maintenance on your chainsaw will ensure the air filter doesn’t have an excessive build-up of dirt or other particles.
Top Reasons Chainsaw Won't Start — Chainsaw Troubleshooting
Find replacement chainsaw parts:https://www.repairclinic.com/Shop-For-Parts/a30/Chainsaw-Parts?TLSID=?1894Visit our Chainsaw Repair Help for more troubleshoo...
Chainsaw gets gas, spark, but won't start
Hi -- I recently bought a used Husqvarna 268SE chainsaw. The previous owner said it started and ran for a while, but then died when it warmed up.
How to start a chainsaw engine?
Now to start the engine of your chainsaw, you must turn it on. You must then prime its carburetor and then you must fit the socket on the nut of your flywheel. To do this, you will have to remove the shroud that covers the engine of your chainsaw.
How to start an electric chainsaw?
For a cordless chainsaw , you must use a backup battery that is fully charged and for the corded chainsaw, you must use a proper extension cord and plug it into a wall outlet.
How to start a gas-powered chainsaw?
Before you try to start your gas-powered chainsaw you must perform a maintenance check. You must make sure its spark plug boot is well fitted. You should then refill fresh fuel and oil mixture specialized for four-cycle engines.
Why do electric chainsaws have a brush?
Some electric chainsaws have a brush inside their motor that is used to conduct electricity. If you are unable to start your electric chainsaw then you must replace the brush inside its motor. You must prefer a brushless electric chainsaw because it is easier to start and needs little maintenance.
How to keep chainsaw engine running?
Closing the choke is what sets its engine to the high idle position. Moving the lever to the “on” or “run” position opens its chokes, but keeps your engine at high idle, which allows the engine of your chainsaw to run consistently.
Why does my chainsaw start with a spring?
The spring-assisted starting system overcomes the engine’s compression to reduce the effort , force, and time needed to start your chainsaw. This spring will automatically release the stored energy to the crankshaft of your chainsaw, and start its engine, quickly and smoothly.
How many times do you push the primer bulb on a chainsaw?
The newer models of a gas-powered chainsaw have an air purge bulb instead. You must push the primer bulb 4 to 6 times to send the fuel into the carburetor, which feeds air and fuel to the engine.
How to start a chainsaw?
Preparation (Before You Start the Chainsaw) How to Start the Chainsaw (Step-by-Step) Step 1: Stabilize the Chainsaw. Step 2: Engage the Chain Brake. Step 3: Turn the Chainsaw On and Open Up the Choke. Step 4: Prime the Fuel. Step 5: Pull the Starting Cord a Few Times. Step 6: Close the Choke.
How to start a chainsaw that has been warmed up?
If you’re taking a short break from using the chainsaw, then you can restart it without using the choke since the engine is already primed with fuel . Place the chainsaw on the ground and put your right foot through the rear handle.
How to stop a chain from spinning?
With your left hand on the top handlebar, lean your wrist forward to push the chain brake handle forward. This will engage the chain brake, which prevents the chain from spinning during the starting process.
What to do when your car fails to turn over?
When you hear the engine failing to turn over, move the choke lever to the halfway position.
How to start sawing?
To start sawing, pull the throttle with the index and middle fingers of your right hand.
How long does it take to move a choke lever?
After 30 seconds of idling time, move the choke lever to the closed position.
Where should a chainsaw be started?
The chainsaw should always be started on level ground; never up in the air or on a high surface.
How long to drill a crankshaft?
Turn the crankshaft with the drill for a few seconds (15).
How to check for leaks in a cylinder?
Remove spark plug and move piston to bottom of cylinder. An air adaptor is then installed in the plug hole and a hand pump that will go both pressure and vacuum is used to check for leaks. 5 psi is all that the case needs to hold either pressure or vacuum.
How to put a chain on a craftsman’s chainsaw?
Make sure that your chainsaw is in a well-ventilated area and there are no flammable materials nearby. Put on your gloves and make sure you don’t have any loose jewelry or accessories on. Turn off the chainsaw and let it cool down for several minutes before attempting to install a new chain.
How to start a craftsman electric chainsaw?
To start a craftsman electric chainsaw, you’ll need to locate the on/off switch. This is typically a red button located on the rear handle of the saw. After locating the switch, hold it down and pull the starter cord slowly until you feel resistance.
How to fix a chainsaw that is not working?
Still not working? Give the chainsaw a break by turning everything off. Flip off the on/off switch. Turn the throttle off. Push or pull the choke to the "off" position and deal with anything else that might need to be switched off. ("Off" is the keyword.) Some even suggest removing the spark plug, pulling the cord a couple of times, then replacing the plug. By doing all this, you will reset the saw and can start the process of clearing a flooded engine.
Why is my chainsaw stalled?
Flooding is caused by too much gas applied at the wrong time and can prevent a saw from starting. It is the major cause of a stalled chainsaw engine. As previously instructed, everything should now be turned off.
How many pulls does a choke need to start?
With the choke in the "off" position, pull the engine's crank cord through again. The engine should start in 1 to 3 pulls. Try it first without using the throttle control—unless recommended by the manufacturer. Colder weather or a saw just out of storage can complicate these instructions.
How to keep a saw clean?
The major things to remember are: Keep the saw clean. Make sure the saw is full of fresh non-ethanol gas, mixed with the correct amount of two-stroke oil, and avoid flooding. Keep up regular maintenance, whether done by you or by a shop.
Can you start a chainsaw with ethanol?
A new chainsaw might give you starting trouble right out of the box if you fuel it with an old gas/oil mixture, especially if it has added ethanol. Always use fresh non-ethanol gas ...
Can you prime a chainsaw if it's flooded?
If a flooded chainsaw is your problem, no extra gas is needed—DO NOT be tempted to prime the saw again. The saw has more than enough gas at the right place and too much is the problem.
