Slide the crimp bead down the wire. Move the crimp bead close to the end of the clasp or end piece. Check the crimp bead and make sure it is not too close to the clasp or end piece. You want to have a small loop around the clasp or end piece, but not so small that it holds the clasp so tightly that it cannot move freely. [5] Flatten the bead.
Full Answer
How do I tie a crimp cover bracelet?
In a regular bracelet, you'll need to leave a larger gap, but not with these stretchy bracelets. Time to tie your elastic cord into a knot. Just make a simple overhand knot and pull it tight. No need to get fancy and bust out your guidebook to boater's knots here - if the knot gets too big, it won't fit inside the crimp cover.
How do you get a knot out of a bracelet?
Use a sterling crimp bead to cover the knot. Just string the bracelet with the crimp at one end, tie the bracelet off and then slide the crimp onto the knot and crimp it or just smash it flat. The sterling is soft enough that it won’t cut the elastic.
How do you make a crimp bead necklace?
Forming the Crimp Beads Slide the crimp bead down the wire. Move the crimp bead close to the end of the clasp or end piece. Flatten the bead. Use crimping pliers to flatten the bead. Round the bead. Round it with crimping pliers. Use chain or needle nose pliers. If you don’t have a pair of crimping pliers, you can use regular pliers.
What is a crimp cover for jewelry?
Crimp covers are meant to be used in jewelry strung on beading wire. Since wire can't be knotted, it has to be finished with a crimp bead, a small metal tube. They aren't very attractive once crimped, so a crimp cover goes over the crimp and, once closed, looks like a bead. It makes wire beaded jewelry look finished.
How to crimp a clasp?
How to make a bead necklace?
How to make a c shape on a bracelet?
How to tighten crimp bead?
How to flatten a bead?
How to make a loop with a clasp?
How to secure beads to a clasp?
See 4 more
About this website
How do you put a crimp on a bracelet?
0:212:15First take your crimp bead. And slide it over the wire second take your lobster claw and slide itMoreFirst take your crimp bead. And slide it over the wire second take your lobster claw and slide it over the wire. You always want your crimp bead to be in between your beads and your lobster claw.
How do you crimp a clasp bracelet?
2:535:10Run your bead wire through the other end of the clasp. And back through the crimp bead. You want toMoreRun your bead wire through the other end of the clasp. And back through the crimp bead. You want to position the crimpy. This is very important you don't want the wires to cross.
Do you need a special tool for crimp beads?
Crimp beads are soft metal beads used in place of knots to secure clasps and beads onto un-knottable stringing material such as beading wire. To use crimps, you will need some flat nose pliers to squash the crimps, or speciality crimping pliers that "fold" the bead into a small volume.
How do you crimp a beaded bracelet?
5:266:44Using I'm putting that groove. On these pliers right through the center of these two wires. So I'mMoreUsing I'm putting that groove. On these pliers right through the center of these two wires. So I'm crimping down that way. Then I rotate 90 degrees and I squeeze those two wires. Together.
How do you secure the end of a bracelet?
2:0213:38After your bracelet a song enough to go around your wrist you want to finish up by tying a knot atMoreAfter your bracelet a song enough to go around your wrist you want to finish up by tying a knot at the end I separated the strands by colors and tied a knot at the end of.
How do you connect the ends of a bracelet?
0:585:06Now you need some movement jewelry needs to move so don't put it too near the clasp slightly awayMoreNow you need some movement jewelry needs to move so don't put it too near the clasp slightly away from that toggle clasp and just squeeze it to tight with your flat nose pliers.
What can I use instead of crimp tool?
Use the knife's edge or a thin screwdriver to press the metal contacts to the wires. If that didn't work then you can buy another cable.
Can I use pliers instead of crimp tool?
Can you crimp wires with pliers? No, you can't crimp with pliers, because they won't create the proper cold weld connection that a crimping tool will. A poor crimp can result in air and moisture getting inside the connection, which can lead the connection to fail. Instead, invest in a specialist crimping tool.
What can I use instead of crimp beads?
An alternative to crimp beads and crimp tubes is a newer finding called Screw-Tite Crimps™. Screw-Tite Crimps not only secure your Accu-Flex® beading wire to your clasp, they also allow you to change your clasp for a different one, should you want a different look.
What does a crimping bead look like?
0:362:42As you can see the crimping pliers have two indentations the inner indentation has one rounded halfMoreAs you can see the crimping pliers have two indentations the inner indentation has one rounded half and one v shaped.
How do you use a crimping tool for jewelry?
0:512:50By putting a crimp bead onto. My beading wire just like that then I'm gonna go ahead put the loop ofMoreBy putting a crimp bead onto. My beading wire just like that then I'm gonna go ahead put the loop of my clasp through the beading wire as well and go back down through the crimp bead.
What is the difference between a crimp bead and a crimp tube?
Many jewelry designers prefer crimp tubes over crimp beads. The tubes tend to be stronger than crimp beads and less likely to crack and break. Tubes may do a better job of gripping beading wire because they tend to have a larger interior surface area.
How do you use a crimp clasp?
0:192:42Half you insert the crimp bead or crimp tube in that indentation first and it crimps the bead.MoreHalf you insert the crimp bead or crimp tube in that indentation first and it crimps the bead.
WHAT IS A crimp clasp?
A beaded piece of jewellery can be attached to the clasp in a number of different ways. Crimps are little tubes of metal designed to be 'squashed' together to secure the design. They look neat and are a really popular choice in jewellery making.
How do you finish a lobster clasp bracelet?
Take into account an extra length of beading wire for the finish. Now first string the crimp bead onto the beading wire, followed by the lobster clasp. Then thread the end of the beading wire back through the crimp bead to form a loop and pull it tight until the lobster clasp sits tightly secured on the beading wire.
How do you wire wrap a clasp?
10:1515:41Different approach here. So I'm just going to wrap this around I don't know two or three. Times.MoreDifferent approach here. So I'm just going to wrap this around I don't know two or three. Times. It's up to you how many wraps you want to have in there. I'm going to wrap mine around twice.
How to Choose the Correct Beading Crimp Type and Size
Crimp tubes and crimp beads designed for beading wire are available in a variety of diameters. As you gain experience, you'll likely develop your own crimp size preferences and learn which size works best for the various wires you use.
How to crimp a clasp?
Slide the crimp bead down the wire. Move the crimp bead close to the end of the clasp or end piece. Check the crimp bead and make sure it is not too close to the clasp or end piece. You want to have a small loop around the clasp or end piece, but not so small that it holds the clasp so tightly that it cannot move freely.
How to make a bead necklace?
Thread your first bead onto the wire. Thread the extra tail of wire through the bead hole. Use your flush cutters to cut off the loose end of the cord as close as possible to the bead. Thread the rest of your beads according to your design until you reach the other end.
How to make a c shape on a bracelet?
Move the crimp bead close to the end of the clasp. Next, use crimping pliers to flatten the bead in the middle to form a " c" shape and round out the shape . Thread the rest of your beads onto the wire according to your design until you reach the other end.
How to tighten crimp bead?
When you are ready to attach your final clasp to the end of your piece, thread the crimp bead and clasp just like before, but now you will want to tighten all of your beads by pulling on the tail end of the loose wire. This will snug all your beads up together, leaving no gaps in your design.
How to flatten a bead?
Flatten the bead. Use crimping pliers to flatten the bead. Squeeze the beads with the flatter back channel of the crimping pliers that is closest to the handle . Gently but firmly squeeze the pliers closed. This will both flatten and place a dent in the middle of the crimp bead so that it resembles the letter “C”.
How to make a loop with a clasp?
Form a loop. Form the loop through the clasp and crimp bead. After threading the crimp and clasp, feed the wire back through the crimp bead, forming a loop. It is a good idea to leave a tail of wire a couple of inches longer than you think you need so you will have some wire to work with.
How to secure beads to a clasp?
When you are ready to attach a clasp, first thread the end of your beading wire (jewelry cable) through a crimp bead and then through the eye of the clasp.
What is a flat nose plier?
Unlike simply flattening crimps using snipe or flat nose pliers (which can cause flat crimps with sharp edges) the pliers have cleverly shaped jaws so they have a two-step process that creates small, neat crimps.
What is a crimp in jewelry?
A beaded piece of jewellery can be attached to the clasp in a number of different ways. Crimps are little tubes of metal designed to be 'squashed' together to secure the design. They look neat and are a really popular choice in jewellery making.
How to secure a crimp?
The simplest way of securing a crimp is to squeeze it flat with snipe nose pliers. This will give you a flat piece of metal within your design and can cause sharp edges.
What is a wire guardian?
Wire guardians, also known as thread protectors are a clever alternative gimp wire which is also used to cover exposed thread and protect it from wearing against fastenings.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
Can you use a crimping plier to make a metal bead?
These fantastic universal magical crimping pliers transform 2mm tube crimps into little round beads meaning you can you can make them part of your design as they look like metal beads. Plus they won't scratch your skin like other crimps might, as they create a nice smooth ball.
Can you use crimps on silk?
It is important to note that crimps are not always suitable for all projects - some wire, thread and silk can be slightly too dainty (e.g. 0.2mm) for the crimps to keep secure. If this is the case, knotting your thread or wire where the crimp will sit can help to keep it more secure by giving the crimp more to hold on to.
How to secure a crimp bead?
Finish Securing Crimp Bead. Once your crimp bead is secure, trim off excess beading wire. You can either leave a little of the beading wire and insert the beads you string over it, or trim off all of it up to the crimp bead. Just make sure you cut it cleanly using a sharp pair of wire cutters or a beading wire cutter.
What is a crimping plier?
First, let's take a good look at the crimping pliers. This is a tool designed specifically for securing crimp beads. While some jewelry makers will simply use a pair of chain-nosed or flat-nosed pliers and flatten the bead to close it, we prefer to use crimping pliers to secure a crimp bead because I think it gives it a more polished look.
How to attach a crimp bead to a wire?
Now you are ready to attach and close your crimp bead to your beading wire. 1. Take your crimp bead and slip it onto the end of the beading wire . 2. Next, take the end of the wire and loop it back through the crimp bead leaving a small amount of extra wire as a tale.
What is crimp bead?
Crimp beads are most often used when stringing a beaded piece (like a bracelet or necklace) which has been strung with beading wire. The crimp beads finish the end of the beaded piece of jewelry and help create a loop for the clasp to be attached to.
Can you fake a crimp with a regular plier?
As with any other jewelry technique, this takes practice in order to perfect your technique. Get a nice pair of crimping pliers, and do not try to fake a crimp with a regular pair of pliers. It just is not the same. Most jewelry and beading suppliers carry crimp pliers and crimp beads.
Can you bead a necklace with 4mm beads?
So that the end of the beading wire does not scratch the wearer, make sure your last bead or two on the necklace is large enough so that a small amount of extra beading wire can be threaded back through. I have found that 4mm sized beads work very well for this.
Who is Tammy Powley?
Tammy Powley. Tammy Powley is a freelance writer and jewelry expert. She's an author of 7 books on jewelry making, and has been creating her own designs since 1998. Learn about The Spruce Crafts' Editorial Process. Tammy Powley.
What size crimp covers are used for seed beads?
2. Crimp covers. These are the KEY to making this project work! I used these 4mm crimp covers from Amazon for the smaller seed beads, and these 6mm crimp covers from Amazon for a bracelet with larger pony beads. (Crimp beads are NOT the same as crimp covers).
How to keep beads from falling off of string?
To keep the beads from falling off the string, start with a small piece of tape at one end of the cord. String the beads in the middle first and then add the colorful seed beads evenly to one side. Carefully remove the tape, place tape on the beaded end, and then bead the other end.
What glue to use on elastic cord?
3. Super fast drying glue. This is for your knot, and works great with this kind of elastic cord. Only the tiniest drop is necessary! I used Gorilla Super Glue from Amazon here. You can also use Krazy Glue, nail glue, or Super Glue.
How long should I cut an elastic cord for a bracelet?
Cut a length 12 inches of your .8mm elastic cord. Don't worry, your bracelet will be much shorter, but I've found it's much easier to string beads (especially for kids) if they have some extra room on their string as they bead.
How thick is a letter bead cord?
1. Elastic bead cord. I bought a 2 pack of this cord with a White and Black spool from Amazon here. Just the White spool is sold separately here. This cord is .8mm thick, which is an ideal cord for most letter bead projects.
What is a crimp cover?
Crimp covers are meant to be used in jewelry strung on beading wire. Since wire can't be knotted, it has to be finished with a crimp bead, a small metal tube. They aren't very attractive once crimped, so a crimp cover goes over the crimp and, once closed, looks like a bead. It makes wire beaded jewelry look finished.
How many letter bead sayings are there?
If you’re going to make this project, don’t forget to grab my FREE list of 175+ letter bead sayings, your summer beaders will love it! It’s #172 in my free Resource Library. Get the password below!
How to crimp a clasp?
Slide the crimp bead down the wire. Move the crimp bead close to the end of the clasp or end piece. Check the crimp bead and make sure it is not too close to the clasp or end piece. You want to have a small loop around the clasp or end piece, but not so small that it holds the clasp so tightly that it cannot move freely.
How to make a bead necklace?
Thread your first bead onto the wire. Thread the extra tail of wire through the bead hole. Use your flush cutters to cut off the loose end of the cord as close as possible to the bead. Thread the rest of your beads according to your design until you reach the other end.
How to make a c shape on a bracelet?
Move the crimp bead close to the end of the clasp. Next, use crimping pliers to flatten the bead in the middle to form a " c" shape and round out the shape . Thread the rest of your beads onto the wire according to your design until you reach the other end.
How to tighten crimp bead?
When you are ready to attach your final clasp to the end of your piece, thread the crimp bead and clasp just like before, but now you will want to tighten all of your beads by pulling on the tail end of the loose wire. This will snug all your beads up together, leaving no gaps in your design.
How to flatten a bead?
Flatten the bead. Use crimping pliers to flatten the bead. Squeeze the beads with the flatter back channel of the crimping pliers that is closest to the handle . Gently but firmly squeeze the pliers closed. This will both flatten and place a dent in the middle of the crimp bead so that it resembles the letter “C”.
How to make a loop with a clasp?
Form a loop. Form the loop through the clasp and crimp bead. After threading the crimp and clasp, feed the wire back through the crimp bead, forming a loop. It is a good idea to leave a tail of wire a couple of inches longer than you think you need so you will have some wire to work with.
How to secure beads to a clasp?
When you are ready to attach a clasp, first thread the end of your beading wire (jewelry cable) through a crimp bead and then through the eye of the clasp.
