How do you cut the 12V or 24V LED strip light ? and it is safe ?
- Step 1: Measure the length you need and find the nearest cut line to your desired length.
- Step 2: Use a pair of scissors to cut the LED strip lights directly
How do you wire LED light strips?
You’ll need to plan to do the following:
- Wire the controller (or lights directly) to a power source of +12V and ground
- Mount the light strips securely
- Test and verify operation
How do you work with LED strip lights?
The lights tape’s back come with strong adhesive, a line connect with four strip lights, no need assemble the strip light, easier to install and hide. This cigarette lighter plug has switch and indicator light, built-in fuse, effectively protect the vehicle lights. Suitable for any model cars.
Can you cut RGB LED strips?
To cut Govee Lights, you will need to make sure you have the right type of LED Strip. RGB LED Strips can be cut. This is because they do not contain an IC chip. Meaning they can be cut in certain areas and will continue to work. However, they are also the type of lights that cannot be multiple colors at once.
How to remove waterproofing from LED strips?
How to Remove Waterproofing From LED Strips
- Gather the Strips! Cut the strips you wish to use to their final size. ...
- Coil It! Coil the led strip until it fits into your toaster oven or other heating device and place on a small tray.
- Heat It! Set the oven to a temp below 200F. ...
- Let It Bake! Let the oven (and the strip) heat up for 3 or 4 minutes depending on the power of the oven. ...
- Peel It! ...
- Success! ...
How do you cut power LED strips?
0:264:57How to Cut, Connect and Power LED Strip Lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen cutting your light we recommend using wire cutters. Though if the diodes are really closeMoreWhen cutting your light we recommend using wire cutters. Though if the diodes are really close together use scissors or a razor blade to prevent damage to the LEDs.
Can strip LED lights be cut?
LED Strip Lights are such a versatile product due to the fact that they can easily be cut on the given cut lines and connected at any point between the copper dots on the LED Strip Lights, cut lengths vary between products.
Can LED strip lights be cut and reconnected?
A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.
How do you connect LED strips after cutting?
0:122:45How to Cut and Connect LED Light Strips. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYourself. Remove the plastic to reveal the circuits and make sure you remove enough to expose theMoreYourself. Remove the plastic to reveal the circuits and make sure you remove enough to expose the letters. Too. You can create a new end or connect two lines. Directly. Now in a pinch.
Can you shorten LED string lights?
Short Answer: No, you can't lengthen or shorten standard series-wired incandescent and LED Christmas tree light strings that are made with 2 or 3-wire harnesses. Even if they work at first, they won't last long.
Can I cut LED strip lights anywhere?
You can, but we wouldn't recommend it. By cutting an LED strip light anywhere other than the designated cutting point, you run the risk of damaging the components on the strip itself, as well as the circuit board.
How do you connect LED light strips without connectors?
1:183:13How to Connect 2 LED Light Strips Together (without special cables or ...YouTubeStart of suggested clipEnd of suggested clipYou know connectors on the other light strip. And then you're gonna use the sticky. Thing. YeahMoreYou know connectors on the other light strip. And then you're gonna use the sticky. Thing. Yeah whatever that's called to stick it down and do that for both sides.
How do you fix ripped LED strips without soldering?
How to use a Tape to Tape connector This is the Tape to Tape connector for single colour LED Tape. ... Cut the LED Tape along the cut line with a pair of scissors. ... Now take your Tape to Tape connector and your 2 pieces of LED Tape that you are looking to join. Open the connector.More items...•
How long does an LED Strip last?
50,000 hoursLongevity. LEDs have an unbelievably long expected life-span, compared to both incandescent and fluorescent lights. With an average life-expectancy of some 50,000 hours, LED strip lights will still be burning bright in 17 years' time, long after their traditional counterparts will have expired.
How many LEDs can you cut in a 12V LED strip?
For 12V LED strips, it allows you to cut it by every 3 LEDs, while 24V by every 6 LEDs, which is considered a “functional unit” in the LED strips. As you can see, many cut points marked on the strip, you can use a pair of sharp scissors cut down the LED strip light at the given cut lines or cuttable mark. And by end of each functional unit, there ...
How to install 120V LED strip light ?
As mentioned earlier, 120 volt LED strip light can be made very long, e.g.10m, 15m, 20m, 25m or 100m is quite common in market.
How to make a selection between DC and AC voltage ?
In summary, if it is small decoration lighting project like in the under cabinet, book shelf or kitchen back lighting without too long run, it is better to go 12 volt or 24 volt.
What is waterproof LED strip light?
Waterproof LED strip lights is wrapped with silicone resin material that keep the LED components from dust and water or moisture. If the LED flex strip light is exposed to water like in the bathroom, kitchen or outside working spaces, taking waterproof version is a must-to-go choice, although it is a little expensive.
How many watts does a LED strip light need?
e.g. if the total watt of the LED strip light is 5mx9.6W/m=48W, you need to spare at least 20% headroom, that is 9.6W (=48W*20%）, then you need to buy a 58W (57.6W=48W+9.6W) or higher.
What do copper dots do?
And by end of each functional unit, there are copper dots which allows to solder external wires to power supply or control lines.
What is LED strip light?
LED strip lights are commonly used for decoration accent lighting in home, outdoor architectural buildings and landscape lighting. There are a lot of users having questions about how to cut LED strip lights and how to connect / join them or reconnect them to a desired length, so today, I’d like to share our knowledge about this product, ...
How to Cut LED Strip Lights
Prior to cutting confirm if the strip you purchased can be cut: because some strips once cut can become unstableDon’t. Proceed to ensure that you completely turn off the power supply. It is exceedingly risky to cut a 24v RGB led strip that is attached to a power source directly.
How to Fix Cut LED Strip Lights
It is important to note that once you cut the LED strip you bought the part that remains will not be functional. If you wish to rejoin them after cutting, you’ll need to utilize an additional 4 pin connection. However, if you cut and connect the light strip incorrectly, it may cause the light strip to cease operating properly.
How to Fix Cut LED Strip Lights
Strip connections are the most convenient choice since they do not require any tools. Begin by removing the clear plastic covering the copper pads with a knife. Then, just slide the strip into the connection, making sure that the components match.
Which Type of LED Strip Lights Can Be Cut
Whatever kind of LED strip light you have got, you’ll be sure of 1 thing: you’ll be able to cut it to the length you wish. Throughout your LED strip, there’ll be straight or dotted black or white lines indicating where you will cut. Because the circuits are isolated here, it’s easy to chop on these lines.
Conclusion
So there you’ve got it. LED strip lights could also be adjusted to match the wants of any installation, large or small.
How to connect LED light strip to connector?
Place the two cut ends of the LED light strip into the fastening clips of the connector. At this point, you should check that they are not reversed by following the picture instruction.
What happens if you cut LED lights diagonally?
If you accidentally cut diagonally, it may cause a light to stop working, so make sure you cut straight. Part 2. How to Fix LED Strip Lights When Cut. Q: I purchased a LED strip lights and used a portion of it, but I also want to use the remaining portion.
What size connector for a 10mm light strip?
If your light strip is 10mm wide, the 4Pin connector you select must be suitable for 10mm. If your light strip is 8mm wide and you purchase a 10mm connector, it will not work. Step 2. Open the connector. If the connector has a cover, you have to open the connector on the side. Step 3.
What happens if you cut a Lepro LED light?
If you accidentally cut the wrong place, you may cause the light to stop working normally. After cutting the light strip, you can place the required parts in the proper position and turn on the lights by following to these steps. The following steps use Lepro LED light strips as an example: Step 1.
How to check if light strip is lit?
After placing the light strip, close the cover of the connector and try to see if the light strip is lit normally after the power supply is connected. If the connected parts do not light up normally, try adjusting the connecting point between the connector and the light strip.
What to do if LED light is too long?
If the LED light strip you bought is too long, you need to cut off the extra part. The first thing you should do is measure the right length. If you accidentally cut the strip too short, your effort will be wasted. Step 2. Look for the scissors logo on the light strip.
What does it mean when an LED light is not lit?
After performing the above steps, if you find that the LED light strip is still not lit, check that there is no connection issue. If the set-up is normal, it means the light strip may have been damaged during the cutting process, so be careful and always cut according to the logo on the strip.
How many volts are in a led strip?
Normally, the led strip is generally divided into 5V, 12V, 24V according to the voltage
What is the shape of a wire?
Divided according to shape: cross, L-shaped, T-shaped, one-end wiring, two-end wiring.
Can you use a beetle buckle on a led strip?
Beetle Led Strip Light Connector advantages and disadvantages: Beetle buckle is very suitable for waterproof led strip, but its volume is relatively large, when used with aluminum trough, it will not fit into many smaller aluminum troughs because it is too large.
Can you use a SMD connector in a cabinet light?
However, it also has three shortcomings. It is only suitable for non-waterproof light strips. When you cover it, it is likely to cover one or two SMD led. If it is used in a cabinet light, it may have A small dark area; because it is only clamped inside, his external tension is not enough, and it may fall off in long-term use
Is a COB a high density LED?
The exception here is the COB led strip, which is a high-density led strip with many different led chips on it. Therefore, the COB of different densities has no relationship between voltage and lamp beads. The position of the scissors opening is clearly visible on the led strip.
How to cut LED strips?
Cutting an LED strip is not a very complicated operation, you just have to do it in the right place on the LED strip. To know where to cut on the tape we will find cutting lines materialized by copper points located at regular intervals, generally, we are on a few centimeters. For example, for a 30l/m RGB LED strip, the cutting lines are found every 10cm. For a 120l/m white LED strip, you can cut the LED strip every 2.5cm. The more LEDs the LED strip will have per meter, the closer the cut lines will be. Usually, between 2 crop marks, there are 3 LEDs. It is very important to respect the cutting lengths because if you cut anywhere, it is the section of 3LED that will be defective.
How to install 220V LED strip?
The steps to install 220V LED strips are even simpler. We always start with the introduction of the 4 pin connector to the LED strip. These connectors have two distinct parts: the pointed tips and the rounded tips. These are those which must coincide with the ribbon, those are those which are introduced in the current correcting cable. Once all the elements are connected, all you need to do is plug the strip into the power grid.
How many LEDs per meter are needed?
It may seem like a trivial detail, but the amount of LEDs per meter directly affects brightness and power consumption. For this reason, before proceeding with the installation, it is important to analyze the purpose of the lighting to choose one type of strip or another. These tips will help you choose the correct ribbon:
Do both sides still work when you cut them?
Of Course, both sides of your LED strip light still work if you cut them.
How to remove silicone from LED strip?
That is to say that we will remove the silicone protection if we are in the case of a waterproof LED strip. To remove the silicone we will use a cutter (be careful not to cut yourself), you just have to make a small incision in the silicone to easily remove it. If there is any residue left on the copper points, you can lightly scrape the copper points with the cutter, being careful not to damage the electronic circuit.
How far can LED tape extend?
This type of tape can extend up to 50 meters without fear of voltage drops
How to connect ribbon to transformer?
You will need two cables (red and black) which you will connect with the sign + (+ V) or – (-V) respectively. Then, the power supply will have to be connected to the electrical network.
