If you are putting up the Hardi Plank and have a cement siding blade you can use your skilsaw to make a series of plunge cuts so you get something that looks like a cut up pie, than you use a hammer/pair of pliers to remove the sections. A grinder can do it to. A cement shear works also.
How to cut Hardie board in two different ways?
- Lay your backer board out on a work table or between two sawhorses. ...
- Mark where you’d like to cut the board.
- Like the score and snap method, set a straightedge across your sheet.
- Wait for the saw blade to warm up and come to full RPM before starting your cut.
What is the best way to cut PVC?
- 2 Mark the Cut and Secure the Pipe. Make the cuts as straight as possible to ensure the best possible fit. ...
- 4 Using Scissor or Ratchet-Type Cutters. Place the pipe inside the jaws of the cutter, making sure that the blade lines up with the mark. ...
- 6 Prepare Pipes and Fittings for Connection. ...
What would be the best way to cut slate siding?
Method 4 Method 4 of 4: Using Power Tools to Cut Slate Download Article
- Buy or rent an angle grinder or circular saw to cut through thick slate. Angle grinders and circular saws are suited to cut slate.
- Clamp your slate over the edge of a workbench. It’s important that your slate doesn’t shift around as you cut it or you may make uneven lines.
- Place the blade along the line and pull the trigger. ...
How much does a 4x8 sheet of Hardie board cost?
The Cost. Hardie board siding runs about $0.70 to $5.25 per square foot. This could lead to a total cost of anywhere from $4,700 to $13,300. Considering this, how much does a 4x8 sheet of Hardie board weigh? Additionally, does Hardie board increase value of home?
_small.jpg)
How do you cut a hole in a Hardie board?
A carbide-tipped scoring knife is recommended, but you can also use a utility knife or shears. Never use a high-speed grinder to cut cement board indoors, since this can create a dust hazard.
Can you drill a hole in Hardie board?
It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation.
How do you cut a 4 inch hole in Hardie board?
To cut a 4 ⅛” hole in HardiePlank siding so that you can insert your dryer vent, we recommend using the Exchange-A-Blade 4 ⅛” carbide tipped hole saw. This hole saw is deeper than your standard hole saw so it cuts right through the wall—through the fiber cement siding and the ½” plywood substrate below it.
How do you cut a circle in Hardie board?
0:432:17How To Make A Circle In Cement Board With A Backerboard Scoring ...YouTubeStart of suggested clipEnd of suggested clipAnd then I'm simply going to be boring. It in a circle just like that and as you can see. Now thisMoreAnd then I'm simply going to be boring. It in a circle just like that and as you can see. Now this sir the the rounded. Part is starting to bore out the circle. And we're gonna make it a hole.
How do you cut holes in fiber cement siding?
A scribe, a hole saw, nibblers, and a jigsaw are all good options for cutting fiber cement when anything but a straight cut is required. A circular saw with a special blade is the tool of choice for making straight cuts in fiber-cement siding.
How do you cut holes in siding?
1:563:44How To Drill a Large Hole Through Vinyl Siding Without Tearing ItYouTubeStart of suggested clipEnd of suggested clipYeah it's nicer with a regular hole saw bit works better when going in reverse to go through thisMoreYeah it's nicer with a regular hole saw bit works better when going in reverse to go through this sort of material.
What's the best drill bit for Hardie board?
Equip a power drill with a masonry drill bit for small holes or a carbide hole saw for larger holes, preferably a saw designed for use with fiber cement siding.
Do you need a special saw to cut Hardie board?
what is the best saw blade for James hardie siding? For a larger project, use a fiber cement saw blade with polycrystalline diamond tips; if you're installing Hardie siding on a shed or other small building you can use a fiber cement saw blade with carbide tips.
What kind of saw do I need to cut Hardie board?
You can use a jigsaw, table saw or circular saw, or another tool, as long as it's equipped with the right kind of blade. Once prepared, cut the Hardie board as you would any other material. Mark your line; align the board against the guard as needed and slowly but firmly make the cut.
Can you use a jigsaw to cut Hardie board?
Use a jigsaw to make rounded cuts in the cement board. A jigsaw can cut straight cuts, rounded cuts, and is the best choice if you need to cut a circular piece or an irregular shape out of the cement board.
How do you cut Hardie board by hand?
0:050:50How to cut HardieBacker 12mm Cement Board - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirstly place a sheet of hardy back at 12 mil onto the ground. This is going to allow you to getMoreFirstly place a sheet of hardy back at 12 mil onto the ground. This is going to allow you to get your fingers underneath the piece of board that you're cutting.
Will a masonry blade cut Hardie board?
That's a stone/tile/masonry cutting blade with a diamond 'turbo' rim. It will work for Hardie Backer board or similar fiber-cement products but it'll make a lot of dust, and would almost certainly be awful at cutting any sort of wood or wood paneling - more likely to burn through than cut it.
Can you nail into hardiplank?
Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.
Do you caulk the seams on Hardie board?
James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).
What type of blade is used to cut fiber-cement siding?
polycrystalline diamond-tippedFor cutting fiber-cement siding, it's best to use a 4- to 6-tooth polycrystalline diamond-tipped (PCD) blade made specifically for fiber-cement. Regular carbide blades will cut fiber cement, but they dull relatively quickly, and if you attempt a gang cut, the blades overheat and can warp.
What's the best way to cut fiber cement?
Handheld shears. This is probably the most popular method for cutting fiber cement siding. Handheld shears or 'snippers' look like drill-powered tin snips and cost around $260. They come in two flavors: electric and pneumatic.
Can you use a nail gun on fiber-cement siding?
Nailing Basics Fiberboard cement siding can be hand-nailed, but because it's so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun.
Can I drill holes in a house with siding?
So, can you drill into vinyl siding? You can safely drill into any vinyl sidings if you take a few precautions and follow the correct steps. However, you should avoid doing drilling when the weather is cold as the siding can become brittle. You may want to consider using vinyl siding clips instead of drilling.
What is the best tool to cut siding?
A utility knife is typically the best tool for cutting vinyl siding when you're making longitudinal cuts along the length of a plank. If you're only making a few vertical cuts, it's best to use tin snips or a hand saw. Last but not least, another vinyl siding cutting tool is the circular saw.
Is it OK to drill into house siding?
To prevent cracking, you should only drill into siding if its surface temperature is 60 degrees Fahrenheit or greater. For cold weather drilling, warm the surface of the siding with a hair dryer.
Can you screw things into hardiplank?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel.
How do you drill a hole in cement board?
One method involves using an electric drill fitted with a masonry bit. Since masonry bits come in a variety of sizes, it is easy to pick one up in the exact size needed. Simply attach the bit to the drill, mark with a carpenter's pencil the area that needs to be cut, and drill the bit into the cement board.
Can you screw into Hardie backer board?
Fasten HardieBacker sheets with proper nails or screws (as listed in ''Materials Required'' in the backer installation instructions) every 8'' around the perimeter and all supporting studs. Keep fasteners between 3/8'' and 3/4'' from sheet edges and 2'' in from sheet corners.
Do you need to pre drill Hardie board?
You must pre-drill holes in the material before attaching the screws.