- Mark your cable for cutting. It's best to measure your cable a few times. Make sure you're sure about how much length you need.
- Bend the cable at the mark. Place your hands on either side of the mark you made. ...
- Place a saw blade at a 45-degree angle to the armor and begin sawing. You should place the saw blade on the armor where it's beginning to pop up.
- Rotate the cable so you can cut through the other side. Once you've sawed through the armor on 1 side, flip the cable over.
- Remove the excess armor. Once you've cut completely through the armor, you'll have excess armor to the right of your cut.
- Remove the jagged edges of the remaining armor. Using a metal file, gently sand down the edge of the armor where you made the cut.
How do you cut armored cable?
Armored cable is used for electrical wiring installed in an area where it needs protection, like inside of walls. The best means for cutting it is to use cable cutters, which are designed specifically to cut through armored cable without damaging wires. If you are only making a few cuts, you can use side cutters to cut through the armor instead.
How do you cut a cable with a side Cutter?
Cutting Armored Cable with Side Cutters Measure your cable and mark it for cutting. Bend the cable where you want to make the cut. Insert a diagonal cutter into the opening of the armor. Cut off the excess armor. Slide off the waste piece. Cut the wires to length. Trim the sharp ends of the remaining armor.
How do you cut a wire to bend it?
Bend the cable where you want to make the cut. Place your hands on either side of your mark. Then push down on both sides, causing the cable to bend at the mark. Once you have the beginning of a bend, take the cable in one hand and squeeze it until the coils begin to come apart.
How do you cut power cables without damaging them?
Safety gloves should always be worn when cutting cable and jagged edges should be trimmed to provide a clean end. A third option to cut cables is to use a hacksaw. This method is similar to using side cutters. First bend the cable until the armor begins to pop open.
What can you use to cut armored cable?
The best means for cutting it is to use cable cutters, which are designed specifically to cut through armored cable without damaging wires. If you are only making a few cuts, you can use side cutters to cut through the armor instead. Using a saw blade is okay if you don't have any other tools.
How do you cut Armoured steel cable?
5:2611:35How To: Terminate a Steel Wired Armoured cable - Electro 05YouTubeStart of suggested clipEnd of suggested clipWe can circle around the cable. So you can care not to cut through the cable. And damaging our youMoreWe can circle around the cable. So you can care not to cut through the cable. And damaging our you know conductors. Once we've done that we need to remove the inner sheave in.
How do you strip aluminum armored cable?
0:451:47CUT / STRIP OFF Electrical MC metal cable in LESS THAN 30 SECONDS!YouTubeStart of suggested clipEnd of suggested clipThe metal cable like that you see and then the devel cable will unwind. So that now all you have toMoreThe metal cable like that you see and then the devel cable will unwind. So that now all you have to do is wiggle it so that you can snap. That part or you can take a metal snip.
How do you strip back armoured cable?
6:3110:46How To Strip a Steel Wire Armoured (SWA) Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipI need to cut a small section of the outer sheath and to expose a little bit more of the armor andMoreI need to cut a small section of the outer sheath and to expose a little bit more of the armor and you'll see why in a moment the cut i'm going to make i usually allow for about a thumb's width.
What is the appropriate tool used in cutting flexible armored cable?
BX Cable Cutter and Armored Cable Cutter, Cut Flexible Conduit and Armored Cables, with Storage for Extra Blades. The Klein Tools BX and Armored Cable Cutter is simple to use.
How do you strip large armored cables?
2:003:49Proper Removal of Armor From Southwire AIA Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd with a slight twisting motion separate the corrugations. And the armor just pulls off the nextMoreAnd with a slight twisting motion separate the corrugations. And the armor just pulls off the next step will be to remove the fillers in the outside.
Can armored cable be exposed?
It is permitted for indoor or outdoor service, feeder, or branch circuits and can be exposed or concealed.
How do you strip a MC cable without tools?
2:377:05How to install, strip and cut MC cable with no special tools - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd basically what i'm gonna use is just regular tin snips. And get right in between those groovesMoreAnd basically what i'm gonna use is just regular tin snips. And get right in between those grooves which is the weakest.
How do you cut steel cable cleanly?
0:571:57Cut Wire Rope Without Cutters - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the cold chisel in between the two pieces of tape. And give it a good whack. And now you haveMorePlace the cold chisel in between the two pieces of tape. And give it a good whack. And now you have a nice cleanly cut piece of wire rope. This method won't be too useful if you're out in the field.
How do you cut Armoured cable UK?
1:228:434 - Stripping and Termination of a SWA cable - Hull College ElectricalYouTubeStart of suggested clipEnd of suggested clipAnd partially cut through the inner armorings a junior hacksaw is used for this size of SWA largerMoreAnd partially cut through the inner armorings a junior hacksaw is used for this size of SWA larger sizes may require the full-sized hacksaw to achieve this same operation.
What tools cut metal conduit and armored cable?
Cutting the armor without damaging the wires is probably the trickiest part of working with MC cable. The best method is to use an armored cable rotary cutter.
How do you cut cable without a wire cutter?
It's possible to use a hacksaw to cut wire if no cutter is available. You'll want to use a blade with a high teeth-per-inch (TPI) count for as clean a cut as possible. Regardless of the TPI count, using a hacksaw to cut wire is difficult unless the wire has a large diameter.
What is armored cable?
Armored cables, or cables that are sheathed in steel armor, protect your wires while still offering flexibility. However, the armor makes cutting a challenge. Follow the steps below to cut your armored cables correctly with a hacksaw.
Can you use an armored cable cutter?
If you have an armored-cable cutter, you can use this for the job. However, if you do not have one of these special tools, you don't need to go out and buy one. Instead, use a hacksaw and the following steps.
How to cut a cable?
Bend the cable where you want to make the cut. Place your hands on either side of your mark. Then push down on both sides, causing the cable to bend at the mark. Once you have the beginning of a bend, take the cable in one hand and squeeze it until the coils begin to come apart .
How to cut cable in a cable cutter?
Place the cable in the cable guide of the cutter. Under the blade of the cable cutters, you'll see an open space that should be about the width of the cable. This is where you insert the cable so that the blade can come down and cut it. Align the second mark you made with the handle of the cutter.
How to remove cable cutters?
Unscrew the thumbscrew and remove the cable. Once you've cut through the cable, unscrew the bottom thumbscrew until the cable is loose in the cable guide. Then remove the cable from the cutters.
How to make armor pop open?
Bend the cable at the mark. Place your hands on either side of the mark you made. Then push down on either side of the mark, creating a bend in the armor at the mark. As you bend the cable, the armor should pop open.
How to cut armor with a cutter?
You may not have a lot of room to get the cutters under the armor at first. Insert as much of the tip of the cu tter into the opening as you can. Then gently work it back and forth until enough of the cutter is in to cut through the armor.
How to remove waste armor from a cable cutter?
When you take the cable out of the cutters, the armor to the right of where you made the cut should be loose. Slide this armor off of the cable, exposing about 6 in (15 cm) of wire for you to feed into your junction box.
How to cut through armor?
Rotate the cable so you can cut through the other side. Once you've sawed through the armor on 1 side, flip the cable over. Then saw through the armor on the other side, being careful not to cut through the wires.
What is armored cable?
Screwdriver. Armored cable is a type of flexible metal hose that is used to protect electrical wiring that runs throughout homes in areas where the building codes requires the use of such protective material. Some cities or municipalities require that metal conduit or armored cable be used to protect the wiring in residential ...
How to connect car armored cable to junction box?
Then, pass the wiring through the lock washer and begin to spin it on to the connector in a clockwise direction. Once the lock washer is hand tight , use a hammer and flat head screwdriver to gently tap the lock washer and tighten it securely. You can now connect the wiring from the armored cable to that in the junction box, or you can use a fish tape to pass wiring through the cable at this time.
How to tighten a lock washer?
Once the lock washer is hand tight, use a hammer and flat head screwdriver to gently tap the lock washer and tighten it securely. You can now connect the wiring from the armored cable to that in the junction box, or you can use a fish tape to pass wiring through the cable at this time.
Where to put anti short bushing?
Place an anti-short bushing at the end of the cable where the cable from the armored cable will meet with the cable inside the junction box. Then, use your fingers to fold back the bonding strip on the bushing.
Can you run an armored cable through studs?
If you'll be running the armored cable through studs or walls, it's probably best to simply run the cable from one point to the other before you actually cut the armored cable. (Tip - if you want to save some time and effort, you can also go ahead and insert your electrical wiring into the armored cable that this point.
What tools do you need to cut armoured cable?
There are no special tools required for knowing how to cut armoured cable. All you need are standard wire cutters, or, if the wire is especially tough, then use a hacksaw.
How can I run an armoured cable to my shed?
There are nine key stages involved in running the cable, which we will cover in more detail below. It’s worth highlighting at this stage that this is very complicated work and if you’re not familiar with electrics there is a real risk of harming yourself or others.
Why do you need to put cables below ground?
Placing cables below or above ground is essential to protect the cable from rodents and stop it from being a tripping hazard.
Do you need permission to run armoured cable?
Whether you want to run armoured cable to a shed or connect armoured cable to a socket, then you’ll need approval.
Is it cheaper to replace armoured wire?
As such, consider that often the cost of replacement wire of the right length can be cheaper (and safer) than buying a kit to join armoured cables.
Can you switch a wire back on again?
Ensure the wire is properly isolated, the connections are switched off – and that they cannot be switched back on again.
Can you lay wire yourself?
To save money you can lay the wire yourself and hire an electrician to test and connect it, saving you the hassle of wondering how to connect armoured cable to a socket. Placing cables below or above ground is essential to protect the cable from rodents and stop it from being a tripping hazard.
How to cut a cable to expose conductors?
First bend the cable until the armor begins to pop open. Next take the saw blade and cutting at a 45° angle, cut through the remaining armor avoiding coming into contact with the conductors. Once the armor is cut through, remove the armor sheath to expose the conductors.
What is the purpose of side cutters on a cable?
Where the cable has opened use the side/diagonal cutters to cut the remainder of the opening taking care not to damage the conductors. This method is less preferable due to the jagged and sharp edges that are left, causing a potential safety hazard.
Can you cut MC cable?
There are a few ways to cut and install Type MC Cable, but you should be aware that some are quick er and more efficient. Depending on the style of cable and insulation, different factors need to be taken into account to prevent damaging the conductors within.
Do you need red bushings for AC cable?
For all Type AC Cable installations, red anti-short bushings must be inserted into the end of the cable prior to installation. For traditional Type AC and MC cables, view AFC’s installation instructions.