Cutting the Slate With a Slate Cutter Download Article
- 1 Use a slate cutter when cutting through slate that's medium thickness. ...
- 2 Line the straight edge up with the line. ...
- 3 Score the line that you drew with a sharp tool. ...
- 4 Line the slate cutters up with the scored line that you made. ...
- 5 Squeeze the handles together and cut the slate. ...
How do you cut a Slatwall panel?
Slatwall panels can be cut very easily. For straight cuts use a table saw and cut the slatwall panel face UP, or use a circular saw and cut the panel face DOWN. Use a sharp blade with 60-80 teeth and set the blade depth to 1 inch or just enough to cut through the slatwall panel.
How do you cut slate with a table saw?
One blade should be on top of the slate and the other blade should be under it. If the piece of slate is big, clamp it down on a workbench so that it stays still while you cut it. Squeeze the handles together and cut the slate. Hold the handles with both hands and squeeze to start cutting the slate.
What tool do you use to cut slate?
[7] Use a slate cutter when cutting through slate that's medium thickness. This tool has special carbide tipped blades that are resistant to wear when cutting slate. They look like shears or large scissors and will cut through slate fairly easily. Use these if you have to cut through slate that's somewhat thick.
How do you install slats on plywood?
The layered sides of plywood do not sand down smoothly, so try to remove the roughest areas. Lay out the wood slats. Paint or stain the front and both sides of the wood slats (but not the back). Run a bead of construction glue down the length of a slat, on the back side. Begin in a corner and install the first wood slat.
What is a slate cutter?
What to use to cut slate?
How to cut slate with a power tool?
How to make a slate saw spin?
How to score a line?
What size circular saw should I use for slate?
How to draw a line on a slate?
See 2 more
How do I cut 1.5" thick slate | UK Tiling Forum : Tiling Advice - UK ...
The wet saw we used at the time in Cornwall (1984) was provided by a roofer who specialized in renovating old slate roofs, and somehow connected to Delabole - I remember because I did all the phoning around, large table, large wheel, very noisy, but it did work in one cut, slate being around the same thickness and more even, still have a corner piece in the garden now as a low table supported ...
Cutting a piece of old chalkboard slate | DIYnot Forums
I have a piece of an old schoolhouse chalkboard slate about 3' x 4'. I want to cut this slate into smaller pieces to use in my house and my workshop but have no idea how to do this. Can anyone help? I could not determine if this would fit in another category so am posting it here. Thanks in...
How to Cut Slate With a Grinder | Home Guides | SF Gate
As rocky materials go, slate isn't very hard, and you can usually cut through a 1-inch or thinner slab in a single pass with a 4-inch angle grinder without the need to keep the blade wet.
What is a slate cutter?
A slate cutter is a tool that has carbide tipped blades that will not wear out very much when you cut through the slate. They sometimes resemble large scissors and can cut through the slate without a lot of hassle in the process.
What to use to cut slate?
One method that you can use is the chisel and hammer. This works well if you have thin slate to work through. This provides the most accuracy, but can be hard when you use a thicker piece of slate.
How to cut slate with a power tool?
Slowly lower the power tool that you want to use so it meets the line. Then move it up and down, cutting through the slate slowly. Continue to hold onto the trigger and move the power tool across the line.
How to make a slate saw spin?
Take the blade of the power tool and place the blade along the line before pulling the trigger. You need to also plug in the saw and make it turn on. Use both hands while placing the blade right above the line that you drew on the slate. Then pull the trigger and get the blade to spin.
How to score a line?
Score the line: Use some kind of sharp tool to help score the line . A chisel or a trowel will work well for this to make a small indent into the piece that you are using.
What size circular saw should I use for slate?
Use a circular saw combined with a circular saw fence if you need more accuracy in your cut. A quality mini circular saw can handle slate that is less than 1″ thick.
How to draw a line on a slate?
Figure out where you would like to draw the line on the slate to have it be the size that you would like. Check the line a few times to make sure that it falls where you would like. Mark the measurements on all sides if you need it to be adjusted all over. Then use a straight edge to make a full line.
How to cut slate with a chisel?
Place the chisel on the line and lightly tap on the top of it. Put the flat, straight side of the chisel into the indentation that you created. Lightly tap the top of the chisel with a hammer to break off sheets of slate. Continue to work down the line in the slate until the piece that you want is cut. If you scored the slate well, it should break off in clean, straight pieces.
How does wikihow mark an article as reader approved?
wikiHow marks an article as reader-approved once it receives enough positive feedback. In this case, several readers have written to tell us that this article was helpful to them, earning it our reader-approved status.
How to cut a straight line on slate?
You can use a ruler or a straight piece of wood as your straightedge. Put the ruler or wood on top of the slate and use a pencil to draw a straight line across the section that you want to cut. This line will guide you as you cut your slate.
What to do if slate is dark?
If your slate has dark or discolored spots, cut them away before you cut it.
How to minimize dust when cutting slate?
To minimize the amount of dust produced when you cut your slate, soak the slate in water for a minute or two before you cut it.
What is the best way to cut slate?
This method is best used on thin slate, as the chisel may not be able to cut through thicker pieces of slate.
How to line up slate?
Line a straightedge up with the line that you drew. Get the straightedge that you used to mark your line and place it over the slate. The line and edge of the wood or ruler should line up.
How high should a slat wall be?
When configuring a slat wall display, the area at eye level, between 5 ft and 6 ft height, should display the items requiring the most emphasis and ease of access.
What is a slat wall?
Slatwall is a wall paneling material used to display, store, and organize items on your wall. The panels have slots or grooves which are used to hang shelving, hooks, wire baskets and many other accessories. The panel itself is a 4 ft x 8 ft, medium density fiberboard material that weighs approx 85 lbs.
How many square feet are in a 4 x 8 slat wall?
It is important to first estimate the number of slatwall panels required to cover the desired wall. Each 4 ft x 8 ft slatwall panel covers 32 square feet of wall area. To determine the number of slatwall panels you will need, first measure the length and height of the area to be covered (in feet).
What are the accessories for a slatwall?
A wide range of accessories, hanging displays, hooks, brackets, fixtures, wire displays, and acrylic displays are available for use on the industry standard slatwall display system. Many slatwall accessories are also available to display specific items on slatwall panels such as T-Shirts, shoes, hats, etc.
Can slatwall panels be attached to wood?
Then slatwall panels may be attached directly to the newly installed wood using the above procedures.
Who installs slat wall panels?
We recommend installation of Slatwall Panels by a licensed and insured contractor. Following are instructions and information on how to install slatwall panels, if you choose to do the job yourself ( DIY ).
How to cut 1/2 inch plywood?
Run the plywood lengthwise through the table saw to cut 1/2-inch-wide slats or your desired width. Periodically check strip width to make sure that the width is uniform, as the saw gate may loosen over time. If you are using pre-cut dimensional lumber slats, skip this step.
How far apart should slats be?
To avoid a zebra-stripe effect, spaces between the slats should be less than the width of the slats, So, 1/2-inch slats should be spaced 1/4 inch apart .
How many strips of plywood are there in a sheet?
Cutting a 4-foot by 8-foot sheet of plywood into strips is a more cost-effective approach, but it is more time-intensive. One sheet of plywood yields around 90 to 92 strips, each 1/2 inch wide.
How many strips of wood are needed for a 8 foot wall?
Each one-by-two is actually 1 1/2 inches wide. To cover an 8-foot stretch of wall with a 3/4-inch space between boards would require 48 strips. While softwood strips are inexpensive, the slat wall can still be rather pricey when you need to buy 100 or 200 strips. Hardwood strips are three times more expensive than softwood but require less finishing work.
What is a wood slat wall?
A wood slat wall is the ideal focal point for a room: an accent wall that you'll have for years to come. Building a DIY wood slat wall can be a bit time-consuming, but it isn't complicated at all. Plus, you have a couple of options.
How to fill holes in plywood?
In some places, the sides of the plywood may exhibit small voids or holes. Using the putty knife, fill these in with wood filler.
What is a pre cut wood strip?
Using pre-cut, one-by-two wood strips accelerates the project and helps you avoid having to use a table saw. With this method, most of the work is concentrated on cutting the ends of the boards and nailing up the boards.
josephdamien
I have a piece of an old schoolhouse chalkboard slate about 3' x 4'. I want to cut this slate into smaller pieces to use in my house and my workshop but have no idea how to do this. Can anyone help? I could not determine if this would fit in another category so am posting it here. Thanks in advance for any help or suggestions.
wotan
you could use an angle grinder with suitable stone cutting disc, or for more accurate cutting take it to someone with a tile cutting machine.
josephdamien
Thanks Wotan for your reply. I think I have an angle grinder and will have to get a carbide or diamond blade and give this a try. I also found a Youtube video regarding this and the guy also used an angle grinder. Hope it works. If anyone else has a suggestion, I am open to all! Thanks!
Burnerman
I guess it depends on how thick the slab is, but I'd be looking at water cooling too....helps with the dust at the same time.
josephdamien
Thanks ntb and Burnerman for your responses. And no, I haven't used my grinder very much and so may practice on a small corner of the piece of slate. I may, as Burnerman indicates, need to use some water for the dust and perhaps the heat. I know in cutting tile you need to have water running on the cutting area.
josephdamien
Thanks ntb. I'll be sure to give it good support. I know that it is very easy to shatter. I have some bricks and other items I can practice on. I'll post at some point with my results. Have to get to town and look for a proper blade for the angle grinder. Thanks for your comment.
DIYnot Local
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
What is a slate cutter?
A slate cutter is a tool that has carbide tipped blades that will not wear out very much when you cut through the slate. They sometimes resemble large scissors and can cut through the slate without a lot of hassle in the process.
What to use to cut slate?
One method that you can use is the chisel and hammer. This works well if you have thin slate to work through. This provides the most accuracy, but can be hard when you use a thicker piece of slate.
How to cut slate with a power tool?
Slowly lower the power tool that you want to use so it meets the line. Then move it up and down, cutting through the slate slowly. Continue to hold onto the trigger and move the power tool across the line.
How to make a slate saw spin?
Take the blade of the power tool and place the blade along the line before pulling the trigger. You need to also plug in the saw and make it turn on. Use both hands while placing the blade right above the line that you drew on the slate. Then pull the trigger and get the blade to spin.
How to score a line?
Score the line: Use some kind of sharp tool to help score the line . A chisel or a trowel will work well for this to make a small indent into the piece that you are using.
What size circular saw should I use for slate?
Use a circular saw combined with a circular saw fence if you need more accuracy in your cut. A quality mini circular saw can handle slate that is less than 1″ thick.
How to draw a line on a slate?
Figure out where you would like to draw the line on the slate to have it be the size that you would like. Check the line a few times to make sure that it falls where you would like. Mark the measurements on all sides if you need it to be adjusted all over. Then use a straight edge to make a full line.
