Here’s what you need to do:
- Step 1: Turn the power off to your ice machine.
- Step 2: Flush out the water in the feed lines, storage hoppers, and evaporator of the Scotsman ice machine by running...
- Step 3: Turn the power back on and turn the cold water slowly to fill up your ice machine. You will want an...
- Step 4: Open up the drain on the lowest storage hopper of the...
How do you clean a Scotsman ice machine?
To keep the machine operating properly, these impurities or minerals will have to be regularly dissolved by an acid cleaning, using Scotsman Ice Machine Scale Remover. Directions for this may be found in the section under cleaning. Filters and Treatment In general, it is always a good idea to filter the water.
Where should I place my Scotsman ice maker?
Place your ice maker just where you need it, up to 15metres away, and 1.5metres lower than the actual drain outlet. A progressive water discharge is standard on all Scotsman EC Easy Fit line models. Ice production rates are common identifiers for ice machines.
How do I drain the water from my ice maker?
Open the door and push and release the On/Off switch to turn the machine off. 3. Turn off the water supply. 4. Drain the water reservoir by removing the rubber cap under the reservoir or black drain pulg it’s near the back wall of the ice storage bin. 5. Disconnect the incoming water line at the inlet water valve. 6.
Why won’t my Scotsman Ice Machine Turn on?
If a good cleaning doesn’t fix the problem, it most likely has to do with your water source. Regular cleanings and descaling are two of the best things you can do to keep your Scotsman ice machine running smoothly.
Why is my Scotsman ice maker not draining?
You can check to make sure the drain and drain line are clear. However, the problem could originate from elsewhere in the system. Misshapen ice can occur if the supply line is clogged or the filter is dirty. Otherwise, the problem is likely a leaky hose somewhere inside the machine.
How do you drain a Scotsman Prodigy ice maker?
1:132:25Cleaning procedures on a Scotsman Prodigy Cuber - YouTubeYouTubeStart of suggested clipEnd of suggested clipIncluding the evaporator cover and right side panel push. And hold the clean button to drain theMoreIncluding the evaporator cover and right side panel push. And hold the clean button to drain the reservoir push. And release the clean button again and when the purge valve indicator.
How do you winterize a Scotsman ice machine?
Hold Clean button in for 3 seconds and then release. The pump and purge valve will be ON for 30 seconds. Repeat as needed. Note: All residual water should be removed from the reservoir either with the shop vac or a clean sponge/towel.
How do you unclog a Scotsman ice maker?
1:444:50How to Clean a Scotsman Brilliance Nugget Ice Machine (SCN60)YouTubeStart of suggested clipEnd of suggested clipPull the rubber drain plug located near the back left corner of the bin. And allow the system toMorePull the rubber drain plug located near the back left corner of the bin. And allow the system to drain before returning the plug.
How do I drain the water from my ice maker?
0:341:28Ice Maker Installation Plumbing Code and Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou ice maker supplied with a drain pump system utilize a drain tube connected to the pump.MoreYou ice maker supplied with a drain pump system utilize a drain tube connected to the pump. Reservoir. The drain tube connects to the drain pump discharge tube. Which is routed to the drain.
How do you clean a Scotsman ice machine condenser?
0:512:23How To Clean a Scotsman Ice Machine (Part 1) - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile the machine is preparing for the descaling. Process. Get ready to add Scotsmen clear one theMoreWhile the machine is preparing for the descaling. Process. Get ready to add Scotsmen clear one the approved scale remover for all Scots and the machines. The amount required for the descaling.
How do I winterize my outdoor ice maker?
Ice Makers Icemakers should be shut down when temp drops consistently below 45 degrees. First switch off the power on the unit. Use CO2 to clear water supply line. Remove all ice from the storage compartment, clean it and close the drain valve.Dec 6, 2016How to Winterize Your Outdoor Kitchen - Curto's Applianceshttps://www.curtos.com › blog › 5394-how-to-winterize-y...https://www.curtos.com › blog › 5394-how-to-winterize-y...Search for: How do I winterize my outdoor ice maker?
How long is the Clean cycle on a Scotsman ice machine?
You must run the rinse cycle because it will flush out all of the Scotsman Ice Machine Cleaner from the water system. This rinsing cycle should last about 20 minutes.How to Clean a Scotsman Ice Machine | Hunkerhttps://www.hunker.com › how-to-clean-a-scotsman-ice-...https://www.hunker.com › how-to-clean-a-scotsman-ice-...Search for: How long is the Clean cycle on a Scotsman ice machine?
What does sump full mean?
– Sump Full light is on, but water level is low. – Cause is a shorted water level sensor. – Remedy: Clean sensor probe housing. Page 36. Diagnostic – Water Level Sensor.General Commercial Service - | Scotsman Ice Systemshttps://www.scotsman-ice.com › servicehttps://www.scotsman-ice.com › serviceSearch for: What does sump full mean?
What does sump full mean?
– Sump Full light is on, but water level is low. – Cause is a shorted water level sensor. – Remedy: Clean sensor probe housing. Page 36. Diagnostic – Water Level Sensor.
How do you clean a Scotsman ice maker with vinegar?
Remove all the water from the ice tray with a clean, dry rag. Spray down the ice maker with the vinegar mixture, let the spray sit in the ice maker for about five minutes, then rinse the ice tray with warm water. Pull the rod arm down and start the ice maker again. Dump the first couple trays of ice.
How do I clean my auger ice machine?
Sometimes an auger will appear clean when wet, but after it is dry it will be seen to be stained. Scrub the auger with ice machine cleaner and hot water.
How long is the cleaning cycle on a Scotsman ice machine?
You must run the rinse cycle because it will flush out all of the Scotsman Ice Machine Cleaner from the water system. This rinsing cycle should last about 20 minutes.
How do you clear clean light on a Scotsman ice machine?
One aspect of your ice machine cleaning and maintenance guide is to reset the clean indicator light, and Scotsman says to “press and hold On/Off bu...
What is a Scotsman Clear 1 ice machine scale remover?
This is a product made specifically by Scotsman to clean and descale Scotsman ice machines. It’s a highly-concentrated, food-grade solution that he...
How long is the clean cycle on a Scotsman ice machine?
A full cleaning/descaling cycle takes about 10 minutes. That’s how long it takes the cleaning solution to circulate and penetrate the machine. Once...
Can I use bleach to clean my ice machine?
Yes, and Scotsman actually recommends it. According to them, bleach is a great cleaning solution for the ice bin. According to the cleaning and mai...
Why is my ice maker making dirty ice?
Dirty ice could have to do with dirty machine components, which is yet another reason why it’s essential to stay on top of maintenance. If a good c...
WHEN TO CLEAN YOUR SCOTSMAN ICE MACHINE
When the machine’s “TIME-TO-CLEAN” indicator light is yellow or you’re experiencing any of the following, it might also be a sign that it needs to be cleaned:
WHY CLEAN YOUR ICE MACHINE?
During normal operation, the mineral scale that is in your home water supply will gradually build up on the ice machine’s surfaces. This mineral build-up can hamper the efficiency of the ice-making system. Regularly removing, about every six months, the mineral scale build-up will lengthen the life of your Scotsman ice machine.
WHAT NEEDS TO BE CLEANED
Ensure to wipe up spills when they occur. Wash with warm, soapy water to remove items dried onto surfaces.
HOW TO CLEAN YOUR ICE MACHINE
To ensure you’ll always have the cleanest ice possible, Scotsman recommends regular maintenance of your home ice machine. For more information, please reference the service manual for cleaning instructions for your model.
What is Scotsman Ice Systems?
Scotsman Ice Systems pioneered the advancement of affordable and reliable ice-making machines, for commercial and domestic applications.
How much less should ice machines produce?
If the conditions of your ice machine’s environment are warmer, you should expect the production rates being roughly 20% less than specified. As production is dependent on the environment the machine is placed in, it is vital to consider these variables when establishing which production rate is right for your needs.
What is gravity drain?
Gravity Drain: A gravity drain makes use of the earth’s gravity to help assist condensate from the ice machine. Essentially, if your drain happens to be within one metre of the ice machine and the drain needs to physically lower than the actual drain port from the ice machine, gravity drains will be suitable for you.
What is the ideal temperature for ice machines?
Manufacturers categorise production rates based on their capabilities in optimal environments. The ideal temperatures at which an ice machine should run is: the ambient temperature @ 10°C and water temperature @ 10°C.
Where are commercial ice makers used?
Commercial units are usually used in places such as restaurants, bars, hospitals, supermarkets, etc. Home Ice Makers, particularly built-in and under-counter ice makers, are ideal for people who either enjoy entertaining others or who love specific types of ice.
Do you need to drain an under counter ice maker?
Commercial and residential under-counter ice makers both need to be drained. There are two main ways of doing so: either by using a gravity drain or a progressive water discharge pump. Let’s compare them:
How to clean a Scotsman ice machine?
1. Scoop out all of the ice, either discard it or save it in an ice chest or cooler. 2. Press and HOLD the On/off button in for 3 seconds until the Green light goes out. 3. Press and HOLD the both the Clean-Reset and On/Off buttons for 5 seconds. The Time to Clean light will blink on and off. 4. Pour 8 ounces of Scotsman Ice Machine Scale Remover (available from a local Scotsman Distributor or Dealer) into the ice machine reservoir. 5. Operate the machine for about ½ hour. 6. Push and release the On/Off switch. The machine will begin to flush out the cleaning solution. 7. Operate the machine for another ½ hour. 8. Push and release the On/Off switch. The machine will stop the cleaning process. 9. Pour a gallon of hot (95°F. – 115°F.) water into the bin to flush out the drain. 10. Clean the bin liner of mineral scale by mixing some ice machine scale remover and hot water, and using that solution to scrub the scale off of the liner. 11. Rinse the liner with hot water. 12. Sanitize the bin interior. 13. Replace the ice removed in step 1. 14. Push and release the On/Off button to restart ice making. The ice scoop should be washed regularly, wash it just like any other food container. Pour Scale Remover Here
How does a Scotsman ice machine work?
The machine takes in room temperature air at the lower right front and forces warm air out the lower left front. Restricting the airflow will adversely affect the ability of the ice machine to make ice. Scotsman Ice Systems are designed and manufactured with the highest regard for safety and performance. They meet or exceed the standards of agencies like U.L. Scotsman assumes no liability or responsibility of any kind for products manufactured by Scotsman that have been altered in any way, including the use of any parts and/or other components not specifically approved by Scotsman. Scotsman reserves the right to make design changes and/or improvements at any time. Specifications and designs are subject to change without notice. Ice Making Area Control Panel Warm Air Out Air Intake
How to remove a thermistor sensor from an ice machine?
If unit was making ice, manually harvest the ice. 2. Disconnect electrical power. 3. Remove top panel. 4. Remove cover from controller box. 5. Disconnect thermistor wire from controller. 6. Locate thermistor sensor, it is attached to the suction line, just above the accumulator and is covered with insulation tape. Remove the insulation. 7. Disconnect sensor bulb from suction line (it’s held on with a metal clip). 8. Remove thermistor from ice machine. 9. Reverse to reassemble. It is very important that the bulb be re-insulated.
How does a water controller work?
The controller uses a Water Sensor to check for the presence of water in the reservoir and to measure the conductivity of the water. The water sensor consists of two stainless steel probes located in a holder next to the water pump. The probes sense the conductivity of the water. The higher the mineral content of the water, the better it can conduct electricity. The control system is capable of sensing water as clean as 10 microSiemens/cm. If the controller cannot sense water and the bin thermostat is closed the controller will power the inlet water solenoid valve to fill the reservoir. The water fill is timed. There is a maximum amount of time allowed from the time the controller turned on the inlet water valve until the water sensor signals to the controller. That time is 2 1/2 minutes. If water is not sensed within 2 1/2 minutes, the controller will not proceed with an ice making cycle. Instead it will blink the Water light and try filling the reservoir in 20 minutes. Reservoir water dilution The process of making ice from circulating water causes the pure water to freeze first, because it freezes at the warmest temperature. The remaining water will develop an increasing concentration of minerals. If that mineral concentration were allowed to continue, eventually the ice machine would become coated with mineral scale. To combat the mineral build up, the reservoir water is diluted with fresh water every cycle. The controller adds enough water to fill the reservoir and extra water to overfill it. The extra water drains out through the standpipe in the reservoir. The controller keeps the inlet water solenoid valve open until the evaporator temperature set point is reached, plus some extra time. The extra time is either pre-set or automatically determined by the controller. Evaporator Pump Reservoir Drain Freeze Cycle Water Schematic Harvest Cycle Water Schematic Standpipe Inlet Water Solenoid Valve
How long does it take for ice to drain from a ice maker?
No adjustments are needed. After about a half hour, ice will fall into the ice storage bin.
How to operate a ice maker?
1. Turn on the water supply. 2. Switch on the electrical power. 3. Push and release the On/Off switch to start the machine. The Ice Making light next to the On/Off switch will glow Green. 4. Water will begin to flow into the unit. When the reservoir is full, water will start to drain from the machine. After a few minutes the compressor, water pump and fan motor will begin to operate and the first ice making cycle will have begun. No adjustments are needed. After about a half hour, ice will fall into the ice storage bin. The machine makes 24 cubes per batch. It is normal for the first batches of ice to melt, that continues until the bin has cooled. It will take 8 to 10 hours of continuous run time to fill the ice bin. When the bin is full of ice, the ice machine will shut off. It will automatically restart when the ice level falls, either from use or normal meltage.
How to connect a ice maker to a 115V outlet?
Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit. 2. Position the unit in the installation opening. 3. Turn on the water supply. Make sure that the ice maker is plugged in and the power is on. 4. Slide unit into installation opening, paying careful attention to water supply and drain connections. Do not kink! 5. Pour a couple of quarts of water into the ice storage bin; on drain pump equipped machines the drain pump should start and water should pump out. Check for leaks. 6. Replace the service access panel. 7. Level the unit as needed.
