Knowledge Builders

how do you drain the oil on a honda gx160

by Jana Gerhold Published 3 years ago Updated 2 years ago
image

How do you drain the oil on a Honda gx160? Take your ratchet and loosen the oil drain plug. Once the plug is loosened, fully unscrew it by hand. Make sure you have an oil pan to collect the used oil. Reinsert the drain plug washer and tighten by hand.

Part of a video titled Oil Change on a Honda GX160 Engine - YouTube
1:04
2:26
Take your ratchet and loosen the oil drain plug. Once the plug is loosened fully unscrew it by handMoreTake your ratchet and loosen the oil drain plug. Once the plug is loosened fully unscrew it by hand make sure that you have an oil pan to collect the used. Oil. Reinsert the drain plug washer.

Full Answer

How many quarts of oil does a Honda gx160 hold?

How much oil does a Honda gx160 Engine hold? Oil Capacity: 0.61 US quart. (0.58 L). Fuel Tank Capacity: 3.3 US quarts (3.1 liters). Fuel: Unleaded 86 octane or higher.

Do you tip to drain carburetor on gxv160?

My Honda mower with GXV160 has a drain plug, but it's inaccessible for changes (right against the deck) and the manual says to tip to drain. The carb doesn't leak if you tip in the direction of the oil filler tube. Never had a problem.

Does my Honda gcv160 have a drain plug?

Philip. Yup- no drain plug on my Honda gcv160 engine either. As much as I'd prefer to have a drain plug, it would probably be a lot more trouble to install one than it's worth- at least to me.

How do you drain the oil from the oil pump?

Remove the plug A or D to drain the oil. Refill the oil and check the level at B or C. I dare say you should replace A or D first before filling. They do make an extension that you can install at either A or D to help facilitate draining in the future or you can use cardboard like suggested.

image

How do you drain the oil on a Honda gc160?

0:522:43How to Change the Oil on a Honda 5hp Engine GC160 - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a 13 millimeter wrench loosen and remove the drain plug. There is a crush washer. Here makeMoreUsing a 13 millimeter wrench loosen and remove the drain plug. There is a crush washer. Here make sure you don't lose it crush washers are a one-time use item.

How do you drain oil from Honda gcv160?

0:252:55Honda Lawn Mower GCV160 Oil Change - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd say that if it has a long filler neck like this one it won't have a drain plug on the undersideMoreAnd say that if it has a long filler neck like this one it won't have a drain plug on the underside of the engine find a clean spot for the oil dipstick tip the mower to dump. The.

How do you drain the oil out of a Honda lawn mower?

1:064:56How to Change the Oil in a Honda Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull it out. Set it aside. Now with something to catch the oil in place next to the more we're justMorePull it out. Set it aside. Now with something to catch the oil in place next to the more we're just going to tip the mower up on its side but the oil flow. Out.

How much oil does Honda gx160 take?

0.6LYOUR ENGINE IN DETAILOil Capacity0.6LFuel Tank Capacity3.1LDimensions312 x 362 x 346mmDry Weight15kg

How much oil does a Honda 160cc take?

FeaturesGCV160GCV190Fuel Tank Capacity.98 U.S. qts (.93 liter)0.98 U.S. qts (.93 liter)FuelUnleaded 86 octane or higherUnleaded 86 octane or higherOil Capacity0.58 US qt (0.55l)0.58 US qt (0.55l)Lubrication SystemSplashSplash13 more rows

Where is the drain plug on a Honda lawn mower?

1:053:50How to Change Oil in a Honda Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I need to turn it to about right there or fill it to about there. So now that the engines hot we'MoreSo I need to turn it to about right there or fill it to about there. So now that the engines hot we're gonna remove the dipstick which is on the right hand side which just unscrews real easily.

How do you drain oil from a lawnmower?

0:121:16How to Change Oil in Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo put a sandwich bag over the opening and screw on the gas cap. Set an oil drain pan on the side ofMoreSo put a sandwich bag over the opening and screw on the gas cap. Set an oil drain pan on the side of the mower near the oil filler tube then tilt the mower.

How do you drain the oil out of a lawn mower without a siphon?

0:364:23How To Change The Oil In A Honda Lawnmower Without A Drain PlugYouTubeStart of suggested clipEnd of suggested clipWell there's two methods you can tip the lawnmower over and catch the oil in a drain pan or you canMoreWell there's two methods you can tip the lawnmower over and catch the oil in a drain pan or you can use an oil evacuator pump.

Can I use 5W30 instead of 10W30 in my Honda lawn mower?

Running Cold If your mower manual calls for a 5W-30 engine oil, using a 10W-30 oil is also acceptable. The only difference between the two oils is the low temperature point, with the 5W-30 functioning slightly better than the 10W-30.

What horsepower is a GX160 Honda motor?

5.5 HP @ 36004-stroke, air-cooled, OHV engine type. Max. Power Output: 4.8 HP - 5.5 HP @ 3600 RPM.

How many horse is a Honda GX160?

SPECIFICATIONSMODELGX160NET POWER3.6kW (4.8HP) at 3,600 rpmCONTINUOUS RATED POWER2.9kW (3.9HP) at 3,600 rpmMAXIMUM NET TORQUE10.3 Nm at 2,500 rpmIGNITION SYSTEMTransistorised magneto ignition16 more rows

What kind of oil does a Honda GC160 use?

Honda recommends 10W30, but 5W30 can also be used, or SAE 30 so long as temperatures are above 50 degrees F (10 degrees C.) This oil should meet API standard SJ or later. To check the oil, remove the dipstick from the filler neck, wipe off any oil, and reinsert it without screwing it back into the neck.

1.Videos of How Do You Drain the Oil on a Honda GX160

Url:/videos/search?q=how+do+you+drain+the+oil+on+a+honda+gx160&qpvt=how+do+you+drain+the+oil+on+a+honda+gx160&FORM=VDRE

20 hours ago How do you drain the oil on a Honda gx160? Take your ratchet and loosen the oil drain plug. Once the plug is loosened, fully unscrew it by hand. Make sure you have an oil pan to collect the used oil. Reinsert the drain plug washer and tighten by hand.

2.Oil Change on a Honda GX160 Engine - YouTube

Url:https://www.youtube.com/watch?v=vmCyqhjMZjU

6 hours ago  · Anderson Industrial Engine is the Midwest's Honda Distributor.Welcome back to our AIE tutorial series to help you get to know your Honda GX 160. Today we ar...

3.Honda GC160; Oil Change and Maintenance - YouTube

Url:https://www.youtube.com/watch?v=JAFYAR6w5wQ

24 hours ago Oil Change Place a suitable container next. to the engine to catch the used. Remove the oil filler cap/dipstick. and the oil drain plug. Allow the used oil to drain. completely, then reinstall the. With the engine in a level position, fill to the upper limit mark.

4.Honda GCV160 oil draining proceedure - Bob Is The Oil Guy

Url:https://bobistheoilguy.com/forums/threads/honda-gcv160-oil-draining-proceedure.70113/

15 hours ago  · Make sure you do the recommended service intervals to your small engine.

5.#HONDA #GX160 OIL LEAK FIX / #FLYWHEEL REMOVAL …

Url:https://www.youtube.com/watch?v=JJTXn5cfzY4

30 hours ago  · Yup- no drain plug on my Honda gcv160 engine either. As much as I'd prefer to have a drain plug, it would probably be a lot more trouble to install one than it's worth- at least to me. I just let the mower sit a few minutes for the oil to drain back into the sump after running it, then remove the filler-cap/dipstick & tilt mower on its side.

6.Honda GX Series Carburetor Service - YouTube

Url:https://www.youtube.com/watch?v=kMw91fiIXNc

1 hours ago  · OIL SEAL PULLERhttps://amzn.to/3eWDhS3HONDA GX160 OIL LEAK FIX / FLYWHEEL REMOVAL / SEAL REPLACEMENT #Honda#OilLeak #FlyWheel #SmallEngineRepair #LawnmowerRe...

7.How To Drain the Fuel Tank and Carburetor of a Honda …

Url:https://www.youtube.com/watch?v=I8J85Q1B_h8

36 hours ago  · i have a brick saw powered by honda gx 160 5.5hp, saw has been running for years without any problems, recently saw cut out and i found fuel getting into oil, drained fuel/oil and removed head assy to find gasket worn, replaced head gasket and reassembled, started fine and was running better than ever, 2weeks later same problem fuel into oil ...

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9