How do you drill a hole in a European hinge? To drill the flat-bottomed hole for the cup, you'll need a 35-millimeter Forstner bit. Mark a depth line ½ inch up the side of the bit, position it on the center point, and bore into the door until you hit the line.
How do you drill holes for a door hinge?
Set up your drill press with a 35mm Forstner bit and a clamped fence to register the edge of the doors when drilling. Bore the cup holes, setting your drilling depth carefully before you begin. Step 3: Insert the hinge cups into the door mortises and make sure the hardware seats fully in the holes.
How to install Euro hinges?
Installing Euro Hinges 1 Make a template Make the template from an old business card. Fold the card around the edge of a scrap of wood. ... 2 Mark the door Determine the location of the hinges on the door. ... 3 Drill the cup hole Using a 35-mm (1-3/8-in.) Forstner bit, drill until the top of the bit is about level with the wood. ... More items...
How to install hinges on a cabinet door?
No matter what type of hinge you choose, the hinges are mounted on the door first and then the cabinet. For installing cabinet hinges, you’ll be drilling two sets of holes in the door. First, there’s the “cup hole,” the large hole that the hinge drops into. This hole is 35 mm (1-3/8 in.) diameter for all Euro hinges.
How do you cut a 35mm hinge on a door?
5) Put the 35mm hinge hole cutter on your drill. The spike on it is the centre locator, so line the spike up with the middle pilot hole. Now carefully drill into the door until the top of the circular hinge hole cutter is level with the surface of the back of the door.
How to determine the amount of overlay on hinges?
What is a Euro hinge?
What is an inset door?
What is a face frame cabinet?
What degree do hinges open?
What does it mean when a door hinge is self closing?
How to mark perfect centerlines for hinges?
See 4 more
About this website
How do you drill a hole in a door hinge?
1:462:45How to Easily Drill Hinge Cups in Cabinet Doors | Glass ImpressionsYouTubeStart of suggested clipEnd of suggested clipHinge. It's the cup hold are drilled use a straightedge to align the hinges and pre-drill withMoreHinge. It's the cup hold are drilled use a straightedge to align the hinges and pre-drill with Rockler self centering drill bits then drive the screws home.
Where do you drill for hinges?
1:142:492 How to Drill a Kitchen Hinge Hole and test Fit Concealed Hinge/InstallYouTubeStart of suggested clipEnd of suggested clipYou need to find the center hole you look inside your hinge hole there's a center hole there andMoreYou need to find the center hole you look inside your hinge hole there's a center hole there and that's where you'll measure to from the front or the top or the bottom of the door.
How deep is the hole for European hinges?
First, there's the “cup hole,” the large hole that the hinge drops into. This hole is 35 mm (1-3/8 in.) diameter for all Euro hinges. You'll need a Forstner bit to drill it ($20 at home centers or online).
What is a hinge drill bit?
0:082:30hinge drills - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that fits in their lap. And then what happens is when you apply pressure the actual drill bit isMoreSo that fits in their lap. And then what happens is when you apply pressure the actual drill bit is spring-loaded.
Where do you drill for European hinges?
Standard hinge holes for these hinges tend to be 35mm in diameter and around 10-12.5mm deep. They should be drilled or bored around 100mm from the top or bottom of the door and 22-22.5mm from the side edge of the door to the centre of the hole.
How do Euro hinges work?
On a standard European hinge, one plate features a cup that rests inside a 35mm hole bored into the back of the cabinet door, while the other plate attaches to the interior side of the face-frame or frameless cabinet box.
How do you use Euro screws?
4:557:47Drilling Euro Hinges - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just stick the cup hinge there in the hole. The really the only key is you want to try and makeMoreYou just stick the cup hinge there in the hole. The really the only key is you want to try and make the tail here on both sides where you're going to attach it to your frame of the cabinet.
How do you replace European hinges?
2:007:29How To Replace European Cabinet Hinges - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo it should just be two screws. And take them out wiggle the hinge and it just simply pops out soMoreSo it should just be two screws. And take them out wiggle the hinge and it just simply pops out so you should find a large hole. And then obviously two holes where the screws were.
How do you adjust a Euro hinge?
0:452:47Cabinet Hinge Adjustments | European Cabinet Hinges - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can by turning it clockwise it moves it closer to the middle by turning it counterclockwiseMoreAnd you can by turning it clockwise it moves it closer to the middle by turning it counterclockwise it moves it further away from the middle so by doing that you will adjust the gap.
How do self centering drill bits work?
Self Centering Bits The nosepiece bevel centers itself in the hardware's countersink and retracts as drilling pressure is applied so that the bit drills a perfectly centered pilot hole. Simply loosen a setscrew to replace the drill bit; replace the spring by unscrewing the hex-drive shank from the knurled body.
How do you use a hinge cutter?
1:222:59Concealed Hinge Jig - YouTubeYouTubeStart of suggested clipEnd of suggested clipMeans all you have to do is use the concealed hinge digs measuring scale to position the hinge atMoreMeans all you have to do is use the concealed hinge digs measuring scale to position the hinge at the desired distance from the top or bottom of the door clamp.
What is a center drill used for?
Center drills consist of a pilot drill and a countersink. They are used to create holes at the center of a piece of stock so it can be turned between centers on a lathe in metalworking applications.
How do you center a screw hinge?
0:162:54Fast simple hinge install and centering of the screws - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn that conical point there it automatically centers the screw. Gives you a recess gets rid of theMoreIn that conical point there it automatically centers the screw. Gives you a recess gets rid of the extra material. Makes it really easy now you can do this with larger larger hinges or smaller inches.
How do you fit cabinet hinges?
1:0114:57How to fit concealed (Euro-style) hinges for overlay & inset cabinet ...YouTubeStart of suggested clipEnd of suggested clipFrom the edge the hinge is secured to the door typically with two screws driven. Through the hingeMoreFrom the edge the hinge is secured to the door typically with two screws driven. Through the hinge boss 32 millimeters apart the hinge mounting plate is positioned at the same height as the hinge.
How do you drill a hole in a cabinet door?
1:205:26Drilling & Installing Handles, Knobs, & Pulls - Cabinet DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a sharp point such as a scratch awl or an icepick mark the cabinet through the desired hole.MoreUsing a sharp point such as a scratch awl or an icepick mark the cabinet through the desired hole. You could use a pencil instead to make a temporary mark in case you're not sure of the placement.
How do you use a door hinge jig?
0:403:09Milescraft 1222 HingeMate150 Door Hinge Jig - How to Rout ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSet the template into the template frame. And press it firmly until it seats into place templates inMoreSet the template into the template frame. And press it firmly until it seats into place templates in this kit can be set to cut a quarter inch or 5/8 inch. Radius.
Euro Hinge Installation Tips - Rockler
Last week, we ran through basics of drilling European hinge cup holes and pointed out a few tools that make the operation easy and accurate. This week, we’ll continue with a few tips on the remainder of the hinge installation process, picking up where we left off. With the hinge cup holes drilled, you’re ready to begin laying out the location of the hinge mounting plates on the cabinet.
How to Remove Cabinet Doors With European Hinges | Hunker
Hidden hinges are generally easy to remove and will only require a few tools and a bit of time. To remove your hinges and any residue left behind from them, be sure to grab a screwdriver, some sandpaper or a small chisel, adhesive remover, a hammer and a small container to store any removed materials (a small, clean space off to the side can work just as well, as long as you're careful.)
What jig to use for cabinet hinges?
Which one should you get? If you frequently make multiple cabinets, the ability to drill two hinge cup holes with a single set-up afforded by the Multi Tool Rail Jig-It is a great thing to have. The 35mm Euro Hinge Drilling Jig from Hettich, although more expensive and limited to a single cup hole size, is fast, accurate and durable enough for thousands of hinges. For drill press owners, picking up a few Hinge Cup Drilling Set Up Jigs is the most affordable (although certainly not portable) way to go. And if you’re comfortable with a router, you won’t find a faster method for the actual cutting of the hole than Rockler’s new Concealed Hinge Router Jig-It. In the end, the choice really boils down to shades of difference in the procedure and the price. Whichever route you choose, you can expect the same results: perfectly sized and positioned cup holes for the most popular cabinet hinge on the planet.
How to use a jig on a door?
To use the jig, you position it in the desired spot along the edge of the door, clamp it in place – making certain that the wood stop block is up tight against the door’s back edge – fit the drill guide over the template and drill until the stop collar has fully compressed the return spring and you're prevented from going any farther. It’s that simple.
How big is a hinge cup hole?
Luckily for all concerned, the vast majority of European hinge cups fit perfectly into single, 35mm-in-diameter sized hole.
How far from the top of a cabinet door should the hinge cup hole be?
The vertical placement of the hinge cup holes – how far they are from the top and bottom of the door – is less crucial. For an average sized cabinet door, 3” from the top and bottom is common. Whatever you choose, it is important keep track of the distance from the top and bottom edge of the door to the center of the cup hole; you’ll need that dimension later on when you position the hinge plates on the cabinet.
Can you drill all 3 holes in a jig?
All of the bits are powered by the same hex drive, so you can quickly drill all three holes without having to change tooling. The jig has indexed settings for a number of hinge cup tabs (“tab” is the term commonly used for the distance from the edge of the cup hole to the edge of the door).
How many hinges are needed for a kitchen cabinet?
Our standard-sized kitchen units are 720mm high by 600mm wide, requiring 715mm by 596mm doors with two hinges each. However, you should always measure the existing doors before selecting replacements to ensure you get the exact same size to fit the unit, especially if your cabinets were made to measure.
What is a hinge cup fix?
HINGE CUP FIXINGS – Screws are driven through these holes to secure the hinge cup to the back of the kitchen door.
How deep should a door hinge be?
Standard hinge holes for these hinges tend to be 35mm in diameter and around 10-12.5mm deep. They should be drilled or bored around 100mm from the top or bottom of the door and 22-22.5mm from the side edge of the door to the centre of the hole.
How to tighten retaining screws?
After you push the hinges into place, use a screwdriver to tighten the retaining screws. Gently open and close the door to check that it fits well without gaps or rubbing against other surfaces. If you have difficulty opening and closing the door, or if it’s too easy, you’ll need to fine-tune the door using the adjustment screws. These will allow you to move the door slightly up or down, left or right, or closer to or further away from the cabinet frame. We also have a video guide showing you how to do this.
How many pilot holes are there in a cabinet door?
4) Repeat this process (steps 2 & 3) at the other end of the cabinet door, so that there are 3 pilot holes at each end where the hinges will be positioned.
What is the pivoting section of a door?
HINGE – The pivoting section that allows the door to open and close, which connects the hinge cup to the mounting plate.
Can you use existing holes to install kitchen doors?
To start with, you should have unscrewed and removed the old kitchen doors and any hinge backplates from the cabinets. If your new doors have the same measurements and hinge positionings, you should be able to use the existing holes to install the new doors.
How to find the boring distance on a hinge?
The easiest way would be to download Blum's hinge catalog off their website. They have overlay charts for every hinge, so if you know the overlay you want you can find the boring distance based on your door thickness. I'd still make the mockups but at least that's a place to start that's right 99% of the time.
What is the most overlay for a face frame?
With the face frame mounting plate, the most overlay you are going to get is 19mm (3/4"), but you will likely end up with slightly less. This is also affected by which mounting plate you use. Blum offers three different face frame plates for the European hinges.
How far should I bore a 125 hinge?
I found a spec sheet and was able to determine the boring distance for each of the hinges. I used a 6mm bore distance for the 125's and an 8mm for the 170 hinges. The overlay works out perfectly and still allowed for adjustment in all directions.
What size spacer plate should I use for a hinge?
You can get plates ranging from 1mm to 16mm. Blum makes spacer plates to obtain correct positioning, depending on the particular application. I've used spacer plates when hinging doors that retract into their cabinet, and I'm sure that if you used the proper plates you wouldn't have any trouble with doors binding on their carcass.
How much gap between door and carcass?
Doors should be mounted with a 2mm gap between the door and the carcass, so that when the bumper or bump-on is fitted (to stop damage and reduce noise from the door closing) the door runs true along the length of the cabinet.
Do you need to move a butterfly hinge?
The only hinge that does need to be moved is the Blum bi-fold hinge, which needs to have the center of the bore drilled at 13mm from the edge of the door so that the hinge finishes on the edge of the door, in order for it to work correctly.
Do hinges have to be in line?
Although you say you have many variants, the fact is, most major hinge manufacturers are in line with one another when it comes to hinge bore size and fitment position of hinges. The only real variants are the fixing points on the hinges and hinge plate thickness.
What is overlay dimension?
If the door is an “overlay door” what overlay dimension do you want? The overlay dimension is the distance that the door lays over the cabinet opening. It is measured on an existing cabinet by taking the distance from the edge of the opening to the edge of the door when the door is in the closed position. Once you know what overlay dimension you are going to use you would consult an “overlay table” to pick your mounting plate and your bore distance. The bore distance is the distance from the edge of the cabinet door to the edge of the 35mm hole that is drilled for the hinge. Each hinge will have an “overlay table” that will help you determine which mounting plate and what bore distance to use to give you the overlay that you want.
What is European hinge?
European style hinges are a modern high-tech hinge for cabinets. European hinges may also be commonly referred to Blum or Grass hinges, as these are two of the main manufacturers of this type of hinge. They are typically comprised of two parts: the hinge and the mounting plate. The hinge mounts in a hole bored in the back side of a cabinet door.
Why is it important to reveal a door?
The reveal (reveal is the gap between the twin doors or the gap between the door and the face frame in the case of an inset door) is important because you need enough reveal to keep the door from binding when it is opened. The thicker the door the more reveal is needed.
What are the pros and cons of a door that is closed?
Pros. When the door is closed the hinges are completely concealed. The doors are adjustable after the hinges are installed. The hinges are available in a wide variety of configurations. They are relatively inexpensive. With the proper installation jigs they can be installed fairly quickly.
Where is the mounting plate for a frameless cabinet?
The mounting plate for face frame type cabinets mount on the edge of the face frame itself.
Where is the mounting plate on a compact hinge?
Compact European hinge with mounting plate on the front surface of the face frame.
How to determine the amount of overlay on hinges?
If you choose overlay doors, you’ll have to decide how much. With some frameless hinges, the amount of overlay is determined by the thickness of the mounting plate; a thicker mounting plate results in a lesser overlay.
What is a Euro hinge?
Euro hinges—also called “cup hinges” or “concealed hinges”—look complicated. But they’re actually much easier to install than traditional hinges. Learn how to fix kitchen cabinets with Euro hinges here.
What is an inset door?
Inset doors are flush with the front of the cabinet; overlay doors cover all or part of the front. Some doors, called “partial inset” (not shown) are a combination of both. We show frameless cabinets here, but the same terms apply to face frame cabinets. Want to refresh your cabinet doors? Learn how here.
What is a face frame cabinet?
Face frame or not? A frameless or “Eurostyle” cabinet is basically a box. A face frame cabinet has a frame surrounding the opening of the box. Hinges like the face-frame hinge shown above mount onto the face frame, typically with a single screw.
What degree do hinges open?
The simplest, smallest and least expensive hinges usually open to 105 or 110 degrees. If you want your doors to open farther for easier access inside the cabinet, the hinges will be bulkier and more expensive.
What does it mean when a door hinge is self closing?
Most Euro hinges are self-closing, which means doors slam hard and loud. Pick up sheets of adhesive-backed cabinet bumpers at any home center for a couple bucks.
How to mark perfect centerlines for hinges?
To mark perfect centerlines for the hinges, lay the cabinet box on its side and center the door against it. Then trace along a marking block (2 to 3 in. wide). Use masking tape labels to match doors to their locations.
