How do you drill a hole in a hinge cup? To drill the flat-bottomed hole for the cup, you'll need a 35-millimeter Forstner bit. Mark a depth line ½ inch up the side of the bit, position it on the center point, and bore into the door until you hit the line. Blow out the shavings and test-fit the cup to make sure the hinge flanges touch the door surface.
Can you cut hinge hinge cup holes without a drill?
Finally, here’s an option that doesn’t rely on a drill for cutting the hinge cup hole. With Rockler’s new Concealed Hinge Router Jig-It, you can buzz out 35mm cup holes quickly and efficiently with a plunge router. Like the Jig-It drilling jig, the Router Jig-It comes pre-drilled with screw holes to set up for holes centered on either 22.
How do you drill hinge bores?
So, to install the cups of a huge variety of hinges, all you need to be able to do is consistently drill one size of hole in one of two spots. In the cabinetmaking industry where time is of the essence, sophisticated methods for drilling hinge bores have long been in practice.
How do you Mount Cup holes vertically on a door?
When it comes to positioning the cup holes vertically on the edge of the door, it’s best to develop a system and stick with it. The Jig-It Multi Tool Rail, a modest upgrade from the original Jig-It system, can help with that. The Multi Tool Rail Master Pack comes with a 30” aluminum T-track and two drilling templates.
What size hole do hinge cups come in?
Luckily for all concerned, the vast majority of European hinge cups fit perfectly into single, 35mm-in-diameter sized hole. And the placement of the hole, while exacting, falls in one of two places for a great many popular hinges: centered on either 22.5mm or 20.5mm from the edge of the door.
How do you cut a hole in a hinge?
2:155:40How to drill hinge hinge holes in kitchen doors - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo out the three holes you want to put the spike into the center locator. Basically what you do isMoreSo out the three holes you want to put the spike into the center locator. Basically what you do is you drill deep enough that this bit is just inside the face of this doll.
Where do you drill holes in hinges?
Standard hinge holes for these hinges tend to be 35mm in diameter and around 10-12.5mm deep. They should be drilled or bored around 100mm from the top or bottom of the door and 22-22.5mm from the side edge of the door to the centre of the hole.
How do you drill a hole in a Blum hinge?
4:237:05How to Easily install Concealed Cabinet Hinges (35mm Hole ...YouTubeStart of suggested clipEnd of suggested clipThat we just drilled out for them I'm apply pressure going this way just not too much pressure youMoreThat we just drilled out for them I'm apply pressure going this way just not too much pressure you don't start bending your straight board and then use this little self centering drill. Bit.
How deep is a hinge cup?
First, there's the “cup hole,” the large hole that the hinge drops into. This hole is 35 mm (1-3/8 in.)
Are all hinge holes the same size?
They come in two sizes 35mm dia and 26mm dia hole size. Most hinges used are the 35mm dia. 26mm dia hinges are sometimes used in small bathroom cabinets or budget carcasses.
What is hinge boring?
Hinge boring is simply the process of drilling out the hinge cup, as well as two smaller holes above and below the cup where the hinge attaches.
How do you use a hinge drill jig?
1:222:59Concealed Hinge Jig - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe jig in place and the hinge cup hole will be positioned correctly every. Time after the cup holeMoreThe jig in place and the hinge cup hole will be positioned correctly every. Time after the cup hole is correctly. Located you still need to drill a clean hole to the proper depth.
What is a standard hinge plate drilling set back?
It does not matter what hinges you use--the position of the hinge on the door will always be the same, and that is 23mm from the edge to the center of the bore. The position of the plate can vary, for 90-180, the plate is set at 37mm from the edge of the carcass.
What do you use Forstner bits for?
Forstner bits are unique in their ability to drill overlapping holes, notches on the edges of a workpiece, and angled holes on the face of a workpiece (pocket holes, for example). The bit will cut whether or not the center spur is engaging the workpiece. This feature is unique to the Forstner bit.
How do you install hinge plates?
12:4121:01How to Measure & Install Concealed Hinges on Cabinet Doors - YouTubeYouTubeStart of suggested clipEnd of suggested clipBetween the edge of the piece of wood that I'm using for my jig and the hole. And I'm going to put aMoreBetween the edge of the piece of wood that I'm using for my jig and the hole. And I'm going to put a couple of screws in to fix it into place.
Where do you drill for European hinges?
4:197:47Drilling Euro Hinges - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe really the only key is you want to try and make the tail here on both sides where you're goingMoreThe really the only key is you want to try and make the tail here on both sides where you're going to attach it to your frame of the cabinet. You want to make sure those are pretty even.
How far should hinges be from edge of door?
When installing a brand new door, the top hinge is usually placed five to seven inches from the top of the door and the bottom hinge is usually placed 10 to 11 inches from the door's bottom.
Introduction to kitchen cabinet door hinges
Before we get into it, we need to make sure you understand all the parts involved so you know exactly what we’re referring to in the instructions. We’ll be talking about the most commonly used type of hinges, European-style hinges, also known as concealed hinges or cup hinges.
How to drill holes for kitchen door hinges
When you order kitchen cabinets from Kitchen Warehouse, they usually arrive pre-drilled for easy assembly, unless the doors are directional and can only be installed one way up. You then have the freedom to decide whether these will be right-hung or left-hung doors and drill the hinge holes yourself accordingly.
Mounting new kitchen cupboard doors
To start with, you should have unscrewed and removed the old kitchen doors and any hinge backplates from the cabinets. If your new doors have the same measurements and hinge positionings, you should be able to use the existing holes to install the new doors.
Looking for replacement kitchen doors for a kitchen makeover?
There are many benefits of replacement kitchen doors, but don’t just take our word for it. Browse our website for yourself to discover a stunning range of replacement kitchen door styles, from signature Shaker doors to contemporary handleless kitchen doors, with a variety of finishes including gloss, matt, textures, and paint.
How big is a hinge cup hole?
Luckily for all concerned, the vast majority of European hinge cups fit perfectly into single, 35mm-in-diameter sized hole.
Can you drill all 3 holes in a jig?
All of the bits are powered by the same hex drive, so you can quickly drill all three holes without having to change tooling. The jig has indexed settings for a number of hinge cup tabs (“tab” is the term commonly used for the distance from the edge of the cup hole to the edge of the door).
