- Mix the flakes with epoxy resin and hardener in a plastic container.
- Pour the mixture onto your floor, following the instructions on the package of epoxy you purchased. ...
- Allow at least 24 hours for your project’s finish coat to cure completely before walking on it without shoes; otherwise, you may damage the surface with scuffs or scratches!
How to broadcast flakes?
How long can you walk on a floor?
How long does it take to cure concrete?
How long does epoxy flake floor last?
2 to 3 yearsTypically, epoxy flooring lasts 2 to 3 years in heavy traffic. Commercial properties—like garages, restaurants, or factory spaces—with lots of daily foot traffic can expect this experience. However, with proper care and maintenance, your epoxy flooring may last much longer.
How do you install floor flakes?
1:163:37How to Install a Full Broadcast Flake Floor with Belzona - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a paintbrush apply the material to the edges. First then spread evenly across the entire floorMoreUsing a paintbrush apply the material to the edges. First then spread evenly across the entire floor at the thickness as recommended by the manufacturer. Start broadcasting the flakes immediately.
Why do you flake epoxy floors?
Epoxy Flakes are designed to increase the durability of your epoxy floors while offering a high-quality finish. These epoxy flakes/chips offer texture and color to your clear/transparent epoxy floors. Add some color and texture to your garage or industrial floors for an affordable price.
How many pounds of flake do I need for an epoxy floor?
Step 1: How much do you need? For a full broadcast, you need 12% in pounds of epoxy flake (sometimes called 'chips')of the total square footage of the area you are broadcasting. For a standard 1,000 Square Foot space.
How thick is epoxy flake flooring?
Epoxy thicknesses can range from . 2 – 3 mils to 250 mils (1/4”) or thicker, depending on the application. The thinner epoxy floorings are typically used for new concrete or concrete that is in decent shape and does not need a lot of repair work.
Is epoxy flake flooring slippery?
This type of epoxy floor coating system is made of a solid color epoxy base coat and around 3- 5% of the floor is covered with a flake to provide a decorative floor, These floors can be slippery and if antislip media is added to the topcoat, it will ruin the look of the finish.
Should I sand between layers of epoxy?
Sand down Epoxy Resin First, sand down the entire surface of your piece with coarse sandpaper ( we use 80 grit sandpaper here at ArtResin ). Sanding epoxy resin between coats will not only get out the imperfection, but will also serve to provide some tooth between the first and second layers.
Can epoxy floors be mopped?
Epoxy floors do not need soap, warm water, and a good mop or deck-scrubbing brush should be just fine. If you need extra scrubbing power use something like soft soap to aid you with the tougher spills.
Do epoxy floors scratch easily?
Epoxy flooring is one of the most durable applications available. It is resistant to chemicals, stains, cracks, and scratches. Not only that, but it is the perfect choice where heavy equipment is used because along with everything else - it is impact resistant.
How long do you wait between layers of epoxy?
There are two methods for applying additional epoxy resin coats: 1) sanding down your first layer after having let it dry for 24 hrs or, if you're in a hurry, 2) you can pour a new resin layer every 3-5 hrs. Either of these methods work very well, allowing for a very strong bond between resin layers.
How thick should epoxy layers be?
As long as you pour in 1/8" layers, you can go as thick as you like. The reason we recommend this thickness is two-fold: first, it allows the bubbles to escape properly, and second, it avoids any excessive overheating of the resin. So for best results always pour in a 1/8" layer, and you're good to go!
Do you have to grind floor for epoxy?
Acid etching a garage floor is a great solution for those who are installing the floor themselves and do not have access to industrial grinders. However, for larger commercial jobs, older concrete, or worn floors we always recommend grinding before epoxy installation.
What do you put under peel and stick floors?
Plywood. Plywood can be an acceptable surface for self-adhesive vinyl tiles as it makes a smooth underlayment for peel-and-stick tiles.
How many pounds of flakes do I need for a garage floor?
In most cases, a full coverage flake floor system requires 6-8 pounds of flakes per square foot.
Why do they put flakes on garage floor?
They are used in epoxy and resinous floor coatings to give the floor an aesthetic appeal, texture, hide imperfections and help to build up the thickness of the coating applied.
How do you install floor chips?
1:163:31Basecoat Application- Applying Your Basecoat & Color Chips - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you purchase multiple colors of chips. This should be mixed together in a separate containerMoreIf you purchase multiple colors of chips. This should be mixed together in a separate container prior to beginning the application the chips are applied by tossing them upward towards the ceiling.
How to broadcast flakes?
After the material is backrolled you will begin broadcasting the flakes. The best way to accomplish this is to place several pounds of the flakes into a clean bucket and take small handfuls of the chips and toss them in the air onto the tacky floor. It is important to throw them upward to get a good spread and faster coverage.
How long can you walk on a floor?
The floor can be walked on in 4 hrs. Avoid any heavy furniture for 3-7 days.
How long does it take to cure concrete?
They must be clean and free from any contaminants that may inhibit the adhesion of the resins. Concrete must be cured for a minimum of 30 days and be free of any internal moisture. The slab should be profiled to a minimum CSP-2 from grinding or shot blasting. This means “pretty rough”. You want the surface to be similar to 60 or 80 grit sandpaper. This gives the resin something to grab onto. It is imperative that all dust is thoroughly vacuumed after prep.
How much epoxy do you need for a full broadcast?
For a full broadcast, you need 12% in pounds of epoxy flake (sometimes called ‘chips’) of the total square footage of the area you are broadcasting.
How to do a touch up on a floor?
When you’re done, look at your floor and check for dips and other areas you need to do a touch up. So the process goes: First Broadcast – high up in the air, even spread across the floor. Second Broadcast – between the first broadcast and even with the floor, even spread as well.
How far should you spread a flake?
The general theory when spreading flake is to start high, and then end low. You’ll start at about 10-15 ft broadcast in length, and then gradually work your way closer as you lower your flake spread.
What are epoxy flakes used for?
1.) Epoxy color flakes for decoration. Considering they are available in infinite color combinations architects, designers, contractors, business owners, and homeowners alike, have taken flake floor systems way beyond the residential garage. Color Flakes are now being used in: 2.)
What is the largest size of epoxy flakes?
Epoxy Flakes are for all intents and purposes just paint. They come in different sizes with the largest being 1 inch and the smallest being 1/32inch. By far the most common size is 1/4 inch. 1 inch Epoxy Flakes. 1/4th inch Epoxy Flakes. 1/32 inch Epoxy Flakes. People often ask me questions about those pretty little color flakes we often apply ...
What colors are Flakes?
The color combinations are infinite. Flakes are even available in neon colors like orange, green, yellow, pink, and blue, as well as glow in the dark colors.
How many flakes are in a 2 car garage?
So your average 400 square foot 2 car garage has approximately 50 pounds of flakes on a finished floor. With that amount of flakes on the floor, color flakes don’t hide major imperfections but they can cover up many minor imperfections that comparably priced non flaked epoxy floors don’t cover up.
Is flake floor WD40 slippery?
Just keep in mind that WD40 or tire shine will make your slip resistant floor just as slippery as any other hard surface sprayed with the same. 3.)
Is epoxy flake slippery?
The problem was it only took a couple of drops of water to make that glassy smooth Epoxy flake floor more slippery than a sheet of ice. So in the rainy season, especially in Florida, people would pull into their garage, the floor would be all wet, they would take a step, and slip and fall.
Is a flakes a square?
The flakes are not a set shape like square or round but random in shape to provide better aesthetics. They are UV stable but the longevity of the color is heavily dependent upon the UV stability and quality of the finish coating system which is most always Polyaspartic.
How to broadcast flakes?
After the material is backrolled you will begin broadcasting the flakes. The best way to accomplish this is to place several pounds of the flakes into a clean bucket and take small handfuls of the chips and toss them in the air onto the tacky floor. It is important to throw them upward to get a good spread and faster coverage.
How long can you walk on a floor?
The floor can be walked on in 4 hrs. Avoid any heavy furniture for 3-7 days.
How long does it take to cure concrete?
They must be clean and free from any contaminants that may inhibit the adhesion of the resins. Concrete must be cured for a minimum of 30 days and be free of any internal moisture. The slab should be profiled to a minimum CSP-2 from grinding or shot blasting. This means “pretty rough”. You want the surface to be similar to 60 or 80 grit sandpaper. This gives the resin something to grab onto. It is imperative that all dust is thoroughly vacuumed after prep.
