How To Fill An Elastomeric Pump Before being given to the patient, a qualified pharmacy will fill the device with the medication prescribed inside a sterile environment. The action of filling the pump gets done manually using a one-way valve, either through a peristaltic repeater pump or a syringe.
Full Answer
What is an elastomeric pump?
An elastomeric pump, also known as a balloon pump or ball pump, is a medical device used for infusing medication. Depending on the therapy needed, these medications might include antibiotics, chemotherapy, 5FU, cytostatics, analgesics, and local anesthetics. Elastomeric pumps use pressure to infuse medication.
How do I Disconnect my elastomeric pump after an infusion?
Disconnecting your elastomeric pump Once your infusion is finished, your pump needs to be disconnected from your CVC. You may disconnect your pump yourself, or you may have an appointment at MSK so your healthcare provider can disconnect it.
What is a continuous infusion with an elastomeric pump?
Continuous Infusion with Your Elastomeric Pump 1 About Your Elastomeric Pump. Your pump is a small, lightweight device that will put chemotherapy into your bloodstream at a steady rate. 2 Starting Your Continuous Infusion. ... 3 During Your Continuous Infusion. ... 4 After Your Continuous Infusion. ...
How should I store my pre-filled elastomeric pump?
Typically, pre-filled elastomeric pumps will be stored in a refrigerator or freezer. Therefore it will need to rest at room temperature for a while before beginning the infusion. It is essential to verify that the medication for the infusion is the correct medication for the patient.
How do you fill an infusion pump?
1:004:29Syringe Pump (Running a Syringe Pump) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow keep the piston of the syringe over the side lock and then slowly bring the end to this slot.MoreNow keep the piston of the syringe over the side lock and then slowly bring the end to this slot. And gently push the syringe. Inside.
How do you prime an elastomeric pump?
0:083:08Easypump® ST/LT Elastomeric Infusion Pump Priming and FillingYouTubeStart of suggested clipEnd of suggested clipTwist Off the cap from The Filling port and place it on the sterile surface attach the primingMoreTwist Off the cap from The Filling port and place it on the sterile surface attach the priming syringe to the filling port. Down the syringe plunger until the syringe is empty.
Are elastomeric pumps reusable?
Are elastomeric pumps reusable? No. Elastomeric pumps are disposable.
How do you know when elastomeric pump is done?
Your infusion is finished when the balloon is completely deflated (see Figure 5). Continuous infusion with a pump usually takes about 48 hours.
How do you know when a pump is primed?
Let the pump run for approximately one minute. If you opened any relief valves, wait until water begins to run from them before closing them again. If the pump turns off naturally, it's primed.
Does a pump need to be primed?
For reliable operation, pumps must first be primed; that is, air or gases to be expelled from the suction and impeller eye area and replaced with liquid to be pumped. The pump would not function properly when not completely filled with liquid.
How long does elastomeric paint last?
ten yearsLong-lasting The strong makeup of elastomeric paint gives it much more longevity than ordinary paints. It will last upwards of ten years when applied properly.
In which setting is an elastomeric pump most commonly used?
The elastomeric pump is typically used in acute or chronic (moderate-severe), oncologic or non-oncologic, post-operative pain, when oral therapy is no longer sufficient....This system is mainly used for continuous infusion of:anesthetics;analgesics;anti-inflammatories;chemotherapeutics.
Does elastomeric paint expire?
Long-lasting – Since the makeup of Elastomeric is so strong, it can remain that way past ordinary paints. Elastomeric paint can hold up to ten years, and elastomeric coating can hold up even longer.
How do you sleep during chemo pump?
Where do I keep the pump when I am sleeping? Keep the pump at a height similar to where the infusion connects to your intravenous line. This could be on top of the bedcovers, or on a bedside table. Avoid placing the pump beneath the pillow or bedcovers where it may be too warm.
Can you shower with a chemo pump?
If your medication is delivered via a pump, you must also keep the pump dry when bathing. You can try taking your showers/baths at the same time as your medicine bag changes. OR you can place your pump in a clean plastic bag, seal the bag, and hook the covered pump on a shower hook.
How does an elastomeric device work?
An elastomeric device is a device used to deliver medication through your intravenous (IV) line. Medication is put in a balloon-like chamber, and pressure from the balloon delivers the medication at a safe and steady rate. Your nurse will teach you how to use the elastomeric device, and how to flush your IV line.
How do you prime a pump set?
0:032:27Prime iV tubing and set IV pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake off all the little stickers clamp your tubing take off the excessive things that are attachedMoreTake off all the little stickers clamp your tubing take off the excessive things that are attached to it. Open that pop that off. And then prime it in push it all the way in.
How do I keep my pump primed?
Turn the pump's power back on, and allow it to run as-is for about a minute. If you opened valves on your pump, wait until water seeps out from them before closing. Wait for your water pump to finish its cycle. If the pump turns off naturally, you've fully primed your pump.
How do you prime a line without bubbles?
1:183:02How to PRIME primary IV tubing | NO AIR BUBBLES! | - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you just open it wide like that that is going to allow air bubbles to come in. So slowly openMoreIf you just open it wide like that that is going to allow air bubbles to come in. So slowly open that roller clamp.
What is pump priming?
Pump priming refers to the steps taken to stimulate spending in an economy during or after a recession. Generally, it involves pumping small amounts of government funds into a depressed economy to encourage growth.
What is an elastomeric pump?
Elastomeric pumps - also called balloon pumps - are usually used in the medical field to administer liquid drugs such as local anesthetics , Analgesics, cytostatics or antibiotics (depending on the therapy). The required pressure for administrating the drug comes from the elastomeric layer that is molded inside the pump.
How long does it take for an elastomeric pump to work?
Depending on the pump's size the drug inside the pump can be delivered over a time spread varying between thirty minutes to seven days.
Where does the pressure for administering a drug come from?
The required pressure for administrating the drug comes from the elastomeric layer that is molded inside the pump. When the pump is filled the layer is stretched. The elastic constriction drives the liquid through the tubing and eventually through a flow restrictor out into the patient connection.
Do elastomeric pumps require electricity?
Elastomeric pumps do not require any electricity and are not gravity driven. When placed above or below the patient, flow rate is typically increased or decreased slightly (head height effect). Filling the pump is done manually through a one-way valve using a syringe or peristaltic repeater pump.
