- Turn off the power supply and ensure the working area is safe. ...
- If this is to resize the hole, remove the part of the inner part to suit the new downlight cutout requirement.
- Apply sufficient plaster to the wings to ensure it holds securely in the ceiling, and place the kit to the ceiling cavity and pull down onto the ceiling ...
Full Answer
How do you cut a hole in a downlight?
You can usually find the cut out size listed somewhere on the downlight’s packaging. Put a hole saw on your drill that’s the same size as the cut out. A hole saw has a ring-shaped blade that connects to the end of your drill. Opt for a blade that has carbide or diamond grits to cut the cleanest hole.
How do you fix a hole in the ceiling without drilling?
cut a bit of timber that has say 50mm lap each side of the hole,place above the hole and screw up through the old ceiling either side of the hole so holds it in place now you just cut abit of board to fill the gap and the timber is there to screw up into.
How do you mount a light to the ceiling without drilling?
Push the light into the hole until you hear the clips snap into place. Make sure all the wires go into the hole before your light does. Continue pushing the light straight into your ceiling so the clips go into the hole. Gently push the bottom of the light and listen for a clicking or snapping sound.
How to install a downlight in a ceiling?
Mark the location where you want your downlight with a pencil. Choose a spot that’s between the joists in your ceiling, and draw a dot to mark the center of the light. Make sure the area doesn’t contain any pipes or wires, or else you could damage them when you install the downlight.
How do you fill downlights in ceiling?
1:578:28Downlights Patching Unwanted Redundant Holes - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I can patch up and start to neaten up these furred edges of paper with some sun paper just justMoreNow I can patch up and start to neaten up these furred edges of paper with some sun paper just just knock them off drywall plug pop it into that hole in the center.
How do you fill downlights?
0:279:50How to REPAIR OVER-CUT POTLIGHT! - YouTubeYouTubeStart of suggested clipEnd of suggested clipPaper around the hole and the paint stiffens it up and makes it drop down so in order to do a niceMorePaper around the hole and the paint stiffens it up and makes it drop down so in order to do a nice flat fix on this I'm gonna take some sandpaper. And I got a block of plywood.
How do you fill a hole in a light fitting?
1:013:46Filling Ceiling Holes - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you peel off the plastic front. And then it's this little piece of metal with a messy sticker onMoreSo you peel off the plastic front. And then it's this little piece of metal with a messy sticker on it basically. So then you stick that up on the hole.
How do you cover up recessed light holes?
Covering these holes is as simple as applying a patch to the drywall and painting over the patches to match the color of the paint on the ceiling. If your ceiling has not been painted in a while, you may need to repaint the entire ceiling to get a perfect match.
How do you fill the gap between light fixture and ceiling?
0:072:29How to Hide Gaps Around a Ceiling Light Box - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo ahead and put it up then I'm just going to bend the wires out to hold it up there. Why I getMoreGo ahead and put it up then I'm just going to bend the wires out to hold it up there. Why I get ready it's amount of light. So we'll take the light.
How do you repair a hole in a plasterboard ceiling?
0:353:08How to Patch and Repair a Hole in the Ceiling | DIY | Great Home IdeasYouTubeStart of suggested clipEnd of suggested clipYou just want to make sure that you use plaster screws you'll see with the timber screw it has ribsMoreYou just want to make sure that you use plaster screws you'll see with the timber screw it has ribs underneath the head and that helps it countersink into the timber. But for the plasterboard.
How can I cover a hole in my ceiling?
Paint your ceiling in a decorative pattern. ... Cover your ceiling with wooden planks. ... Add architectural details that cover the holes. ... Install decorative ceiling tiles. ... Add medallions. ... Cover your ceiling with wallpaper. ... Cover your ceiling with fabric. ... Hang decorative items near the flawed areas on your ceiling.
Can you cover recessed lights?
If your home already has downlights installed and now you're just tasked with laying insulation, such as in an attic space, be sure to purchase recessed light covers with a UL rating to create a protective barrier between the top of the light and the insulation.
What is a goof ring?
A goof ring or trim ring is a thin, round or square piece of flat plastic that helps to cover gaps created by mis-cut holes in drywall ceiling applications. Installed by resting on top of the trim flange.
How do you change a bulb in a downlight?
0:241:45Replacing Downlights - YouTubeYouTubeStart of suggested clipEnd of suggested clipAs for CFL downlights some utilize a reflector whereas others do not for a CFL without a reflectorMoreAs for CFL downlights some utilize a reflector whereas others do not for a CFL without a reflector simply twist the bulb loose. And pull the bulb out. And replace it with your new LED.
Can you daisy chain downlights?
Yes, although you can piggy back off each downlight so you shouldn't need the wagos at each light, just where you new cables connect to existing. If you can get above, just use a junction box. Obviously make sure your new downlight are suitable for bathroom use.
Can I fit downlights myself?
Fitting downlights is a job that you can do yourself, however like any electrical DIY project if you are not totally sure about what you are doing them you should get a professional electrician to assist you.
How do you replace a downlight globe?
0:482:08how to replace downlight bulb - remove and install old style globeYouTubeStart of suggested clipEnd of suggested clipCover. So we want to just remove this globe. Here. Slide it out just as easy as that take this globeMoreCover. So we want to just remove this globe. Here. Slide it out just as easy as that take this globe match it up with one exactly the same which we've already got here.
Tips
If you don’t feel comfortable installing the lights yourself, then contact a lighting specialist or an electrician to do the work for you.
Warnings
Never work on electrical wiring while there’s still power to the circuit since you could electrocute yourself.
About This Article
This article was co-authored by Daniel Stoescu and by wikiHow staff writer, Hunter Rising. Daniel Stoescu is a Master Electrician and the Owner and Operator of Home Tech Solutions, LLC in Hampton, Virginia. With over a decade of experience, Daniel specializes in wiring residential, commercial, and light industrial structures.
ThreadJacker Active Member
A regular customer of mine has 8 downlighters in his bathroom ceiling, he wants rid of them as he's sick and tired of replacing the expensive bulbs.
britishblue New Member
If you swap the fitting for ELV downlighters with transformers, the lamps are quite cheap now, and because of the soft start provided by the transformer, the lamps last for ages. I have had 32 in my house and in the last 10 years have only had to replace approximately 8-10 lamps.
frazbertos New Member
cut a bit of timber that has say 50mm lap each side of the hole,place above the hole and screw up through the old ceiling either side of the hole so holds it in place now you just cut abit of board to fill the gap and the timber is there to screw up into.
Big Fat Stu New Member
i would also recommend changing to low voltage lights as these as less likly to blow lamps.
Padai New Member
If it's not too big a room I would just board straight over the top of the whol lot and skim or tape and joint.
brummie taff New Member
Best and quickest way is timber across the hole screwed eitherside of the hole and then fix piece of pb to fit hole. Can then skim straightaway which is very useul when patching on sites.
toomuchworknotenoughtime
I thought this would have been answered somewhere but I've searched and come up with nothing, so apologies if this has been answered before and I haven't searched properly.
Diyisfun
I would patch it with plaster board, using a big dollop of plaster to hold the patch (from the wrong side).
Micilin
Yes, cut a bit of board slightly narrower but longer than the hole. For you say 65 x 120.
hadiya
By using a cardboard you can fill the holes. place the card boards in the holes and apply plaster over the holes.
Diyisfun
He has said thee is access via the floor, hence I dnt use the piece of wire system. (But it may help others)
wozza56
Another way is to put a bit of batten through the hole long enough to go each side of the hole and screw in place from underneath .Then cut some plugs from a piece of scrap plasterboard ( hopefully cut with a holesaw of the same size)srew this to the batten and then tape and plaster
toomuchworknotenoughtime
Thanks for the replies. I'll pop a bit of plasterboad in from above to provide the surface to fill against.
