How do you fit a Blum drawer front? With the drawer box slill in position in the runners proceed as below. Hold the drawer front as shown and line up the plates. Push the drawer front into the sides until both sides click into place. With the drawer front now in position, you can check the clearance all round and decide on adjustments required.
Full Answer
How to install drawer runners for drawers?
Prepare the drawer back for the drawer runners. Before you build your drawer, you need to prepare the drawer back. It’s easier to do this before assembly than after. You need to drill a 1/4″ hole and cut a notch for your drawer glide. You need to do this on both the right and left side of your drawer back.
Are Blum drawer slides easy to install?
Blum installation instructions leave a lot to be desired but the hardware is great. I pretty much always use Blum Tandem plus Blumotion for my drawer slides. Once you learn how to make sense of the drawer sizing instructions, Blum drawer slides are much easier to install than side mounted drawer slides.
How do you attach the front and back of a drawer?
The front and back parts can be attached to the drawer sides in a number of ways: the easiest of which are loose tenons, dowels or pocket screws. Most people have a pocket hole jig so that’s what I’m using for this tutorial. Prepare the drawer back for the drawer runners. Before you build your drawer, you need to prepare the drawer back.
How do I adjust the drawer front and gallery rails?
Hold the drawer front as shown and line up the plates Push the drawer front into the sides until both sides click into place Next, line up the gallery rails with the fixing at the back, and push down to click into position With the drawer front now in position, you can check the clearance all round and decide on adjustments required
How do I install Blum runners?
6:409:16How to Install Blum Soft-Close Undermount Drawer SlidesYouTubeStart of suggested clipEnd of suggested clipAnd the first thing to do is attach the front clips to the drawer. And then those will then attachMoreAnd the first thing to do is attach the front clips to the drawer. And then those will then attach to the drawer slide once it's in the cabinet. And now I can install the slides into the cabinet.
How do you install Blum self closing drawer slides?
12:5623:07How To Install Blum Undermount Drawer Slides - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure that it's three millimeters to do that i'm just setting. My palini pocket roll whateverMoreMake sure that it's three millimeters to do that i'm just setting. My palini pocket roll whatever you have three millimeters eighth of an inch i said i was going to do both imperial and metric.
How do you install under drawer glides?
5:358:36How to Install Blum TANDEM Undermount Drawer SlidesYouTubeStart of suggested clipEnd of suggested clipMost the slides today use clips on the back. So we just put that into this dovetailed opening andMoreMost the slides today use clips on the back. So we just put that into this dovetailed opening and that will screw to the back wall of the cabinet.
How do you adjust Blum Blumotion drawer slides?
0:001:20How To: Tandem Blumotion Drawer Glide Adjustment - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurning. The drawer over you'll see the button that slides forward. And back slide. The button aMoreTurning. The drawer over you'll see the button that slides forward. And back slide. The button a little at a time replacing. The drawer on to the glide.
How do you install self closing bottom mount drawer slides?
0:542:07Liberty - European Bottom Mount Drawer Slide - Installation VideoYouTubeStart of suggested clipEnd of suggested clipSlide the cabinet member. Completely onto the drawer member measure the distance from the bottom ofMoreSlide the cabinet member. Completely onto the drawer member measure the distance from the bottom of the drawer front to the top of the cabinet.
How do you mount a Blum undermount drawer slide?
0:408:30Easy to Make DIY Drawers & Install Blum Undermount Drawer SlidesYouTubeStart of suggested clipEnd of suggested clipAnd then install it in the cabinet with undermount drawer slides you need a half inch space betweenMoreAnd then install it in the cabinet with undermount drawer slides you need a half inch space between the drawer. Bottom. And the bottom of the drawer. So i've set the fence at a half of an inch.
What is an undermount drawer slide?
Undermount drawer glides are pieces of hardware that are found beneath the box of the drawer. They allow the drawer to easily slide open and close. Undermount drawer glides hold more weight and provide more support than drawer glides that are located on the sides of the drawer box.
Can you put drawer slides on the bottom of a drawer?
By flat mounting Drawer Slides underneath as well as using conventional Drawer Slides you can make the drawer more stable.
How do you install Blum tandem undermount drawer slides into face frame cabinetry?
1:202:27How To Install Blum Tandem Undermount Drawer SlidesYouTubeStart of suggested clipEnd of suggested clipPlace once locked in the drawer will slide in them out as intended. Alright so after installing 10MorePlace once locked in the drawer will slide in them out as intended. Alright so after installing 10 sets of drawer slides. Between both the BlueMotion.
How do you adjust drawer slides?
4:195:22How to Adjust Cabinet Drawer Boxes & Glides - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress up on the gray adjustment tab and push forward or backward to adjust the rise or fall of theMorePress up on the gray adjustment tab and push forward or backward to adjust the rise or fall of the drawer front. Check both the left and right sides.
How do you adjust Blum hinges?
1:212:34How To Adjust Blum Hinges & Align Cabinet Doors - Cabinetdoors.comYouTubeStart of suggested clipEnd of suggested clipMake small adjustments while alternating between the top hinge and the bottom hinge until each sideMoreMake small adjustments while alternating between the top hinge and the bottom hinge until each side of the door sits an equal distance from the face frame. The process is similar for the left/right.
Why is my drawer not closing?
If your kitchen drawer will not close all the way, first empty it and try closing it again. If it still sticks, pull it all the way out and place it on a work surface. Check the empty space and see if there is anything in there that would prevent the drawer from closing.
How do you install Blum tandem undermount drawer slides into face frame cabinetry?
1:202:27How To Install Blum Tandem Undermount Drawer SlidesYouTubeStart of suggested clipEnd of suggested clipPlace once locked in the drawer will slide in them out as intended. Alright so after installing 10MorePlace once locked in the drawer will slide in them out as intended. Alright so after installing 10 sets of drawer slides. Between both the BlueMotion.
How do you install a Blum drawer front?
2:514:16Blum Tandembox Antaro - 3 of 3 Fit the drawer front - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy first lining up the brackets to the drawer sites by clipping them out. Then you can attach theMoreBy first lining up the brackets to the drawer sites by clipping them out. Then you can attach the galleries by pushing down from above until the clip into place.
How do you install Blum soft close hinges?
0:000:53How to install Soft Close Hinge - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the tabs that are in the middle. And put those towards to your hole. The easiest way to do itMoreTake the tabs that are in the middle. And put those towards to your hole. The easiest way to do it is as you're pushing towards the hinge in this direction also push it out.
Why is my soft close drawer not working?
The primary reason for self-closing drawer failure is improperly installed guides or a drawer that was built out of square. This can cause the drawer to skew to one side and fail to close all the way. You can adjust this type of drawer using only a screwdriver.
How to make a drawer glide?
But that’s how it is so make sure that for EACH drawer you are building you order: 1 1 pair of drawer glides (sold as a pair) 2 1 Left locking mechanism and 3 1 Right locking mechanism 4 Screws (I use #6 1/2″ for locking mechanism and #8 5/8″ for drawer runner)
How thick is a 563 drawer runner?
IMPORTANT: 563 H Drawer runner is for 1/2″ -5/8″ thick drawer material and that is what these specific notching and boring measurements are for.
What size screws are used for locking mechanism?
Screws (I use #6 1/2″ for locking mechanism and #8 5/8″ for drawer slide)
How to measure drawer front and back?
The front and back should be installed INSIDE your sides. With 1/2″ plywood, the math for the width of your drawer front and back is easy — subtract 1″ from the outer width.
Do drawer slides come in pairs?
You have to order a right and a left locking mechanism for each drawer slide pair you purchase. (The slides come in pairs. The locking mechanisms are sold individually.)
Where is the groove on a drawer?
Make sure you are doing this on the BACK side of the drawer back. The groove for the drawer bottom is on the inside of the drawer. The opposite side of that groove is the drawer back (and the bottom of the drawer back — back.)
Do you have to order both a right and a left locking mechanism for drawer runner?
Yes, you have to order both a right and a left locking mechanism for each drawer runner pair you purchase. The runners come in pairs. The locking mechanisms come one by one like the ants that go marching on.
What is the best drawer slide?
The Blum Tandem series is one of the most popular drawer slides available. They’re commonly heralded as the best drawer slide money can buy. From integrated soft-close (the manufacturer calls it Blumotion), to the tool free adjustments, to their massive versatility, it’s easy to see why so many people love these slides. That being said, there are some important things you should know before you pick these up for next kitchen upgrade. First, these slides are a two-piece design. You select the drawer slide with your desired size and features, then you select the locking device that fits your application. Second, the drawer box needs some extra consideration. We’ll get into all those details down below, so let’s jump into it.
How to get drawer box into opening?
To get the drawer box into your opening, extend your slides all the way out of the opening, and place your box on top of the runners like you see here: Once the box is resting on the runners, just push it on home into the opening. You should here a click as your locking devices engage with the runners.
How to measure drawers for a runner?
So, if you buy an 18” runner, your drawer box should measure 18”, front to back, on the outside of your drawer side material. To make all the sizing easier, we recommend using the same thickness material all around your drawer. For all intents and purposes, it doesn’t really matter what thickness you use for the drawer bottom, but common thicknesses we see are 1/4”, 3/8“, and 1/2”. You can make your drawer sides as tall as you like depending on what you’re going to be storing, so long as you have the proper clearance on your cabinet opening. As for drawer width, you can go just about as wide as you want, but as you go wider you trade off the ability to hold more weight, and at a certain point you will have to use a Lateral Stabilizer to avoid racking and jamming the drawer. We’ll get into more specifics on the drawer box specifications later. Here is a handy chart from Blum describing the critical dimensions for choosing which drawer slide to use.
What is the phone number for Blum Tandem slides?
We really hope this guide helped you. If you still aren’t getting it, please feel free to give us a call Monday – Friday 8am to 5pm CST at (800) 383-0130 to speak to one of our hardware experts, we will be more than happy walk your through the steps, and help you figure out which hardware you should use on your project. Whether you’re upgrading a single nightstand, or working on a whole apartment building, we can give you guidance.
How tall should a drawer be?
You could even make the sides flush with the top of the drawer bottom and create a rollout shelf. In case you are wondering, 1-7/8 ” is the actual runner height.
How thick should a drawer bottom be?
For all intents and purposes, it doesn’t really matter what thickness you use for the drawer bottom, but common thicknesses we see are 1/4”, 3/8“, and 1/2”. You can make your drawer sides as tall as you like depending on what you’re going to be storing, so long as you have the proper clearance on your cabinet opening.
What to do if playback doesn't begin?
If playback doesn't begin shortly, try restarting your device.
