Fit the removable upper nipple in to the throttle pulley and thread the inner cable through the central hole. Turn the throttle twist grip back to its stop and pull the inner cable tightly but not enough to move the carb slide. Then tighten down the upper nipple and test to see if the carb responds.
Where does the choke cable run on a Lambretta?
The choke cable on a Series I through III Lambretta runs from the choke lever on the right side of the glovebox, to the carburetor on the right side of the engine. The cable has two small soldered nipples on each end and must be a specific length to work properly.
How do I adjust the choke on my electric lawn mower?
Ensure that the choke outer cable is flush tight with the choke lever as shown. Put the choke adjuster up to the outer cable, slide on the spring and hold the choke slide in place. You can see that I have marked the inner cable with a black dot to show where the nipple 'should' have been to fit properly. Cut the cable to the correct length.
How do I install a choke cable?
The cable goes from left to right, through the adjuster and spring and in to the cutaway in the choke slide, which you can see in the pic below. Once assembled, it is simply turned down on to the carb. Here you can see the route of the cable over the frame, behind the toolbox. Here is our new choke lever mechanism.
How do you replace a choke cable on a carburetor?
Cut the cable to the correct length. Dip the new end in flux. Add a blob of solder. Slot the new end in the choke slide to ensure a good fit. Now seat the outer cable, and push through the inner. Push on the spring and then the slide. and tighten down on to the carb where indicated.
How do you install a choke cable?
2:4517:41Team G503 Throttle And Choke Cable Installation Willys MB / Ford GPW ...YouTubeStart of suggested clipEnd of suggested clipWe're going to be placing the cable through that opening first and then through the dash. And thenMoreWe're going to be placing the cable through that opening first and then through the dash. And then out the column here i'm going to show you in the front where the grommet hole is it's the third one.
How do you put a choke cable on a carburetor?
1:015:49Installing a new Throttle and Choke Cable SHA Carburetor - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe top of the slide slide it through. And then go up like that. This part is a little tricky youMoreThe top of the slide slide it through. And then go up like that. This part is a little tricky you gotta kind of finesse it through. It helps to remove this so you don't get frayed ends.
How do you fit a Lambretta throttle cable?
Fit the removable upper nipple in to the throttle pulley and thread the inner cable through the central hole. Turn the throttle twist grip back to its stop and pull the inner cable tightly but not enough to move the carb slide. Then tighten down the upper nipple and test to see if the carb responds.
How do you set up a Lambretta gear cable?
0:4633:58Fitting lambretta cables, TV175 rebuild part 11 - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight a thread you look on the left-hand side of the the headset here and you've got this little tabMoreRight a thread you look on the left-hand side of the the headset here and you've got this little tab washer on on series 3s you haven't got that on series twos.
Where do you connect electric choke wire?
For electric choke hookup, attach the bayonet end of the long electrical lead supplied to the positive terminal on the choke cap. The other end must be connected to an ignition activated 12-volt source. The distributor side of the ignition coil is NOT a 12- volt source. It is a 7-9-volt source after cranking.
How do you remove a carburetor choke cable?
0:321:18How to Remove Choke Cable on a Motorcycle - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe hook them to the eye hooks on here tighten them down they don't have to be incredibly tight justMoreWe hook them to the eye hooks on here tighten them down they don't have to be incredibly tight just enough to support the motorcycle. Now we'll be removing the choke cable right here that's an 11 16.
How do you adjust a Lambretta clutch cable?
3:0819:07#lambretta clutch cable adjustment, for dummies! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt one spline in so that when i adjust the cable properly. It should be at that optimal 90 degreeMoreIt one spline in so that when i adjust the cable properly. It should be at that optimal 90 degree angle now the problem is if you if it's too slack like it was here.
How do you rebuild a Lambretta?
0:054:06Lambretta LI Rebuild Part One - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne of the first jobs would do on it on this particular model series free Lambretta really you'veMoreOne of the first jobs would do on it on this particular model series free Lambretta really you've got a crime ring which fits below the head set and between your leg shoes.
How do you change a throttle handle on a scooter?
6:2122:01Scooter Throttle Replacement How To - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight directly underneath the headlight.MoreRight directly underneath the headlight.
How throttle and choke linkage is setup on a Briggs 2 piece carburetor?
0:085:13Choke, Throttle & Governor Linkage Configuration on Briggs & Stratton 4 ...YouTubeStart of suggested clipEnd of suggested clipGoes from the lever right here right to this plastic part at the back here it's just hooked in thereMoreGoes from the lever right here right to this plastic part at the back here it's just hooked in there and when you move the choke lever just shuts it or opens it.
Do I need a choke on my carburetor?
If you live in a warm climate you may not need a choke. Also, most race vehicles will use a carb without a choke. If you do require a choke, you can choose the one that best suits your needs. If you want more control, you can choose a manual choke.
How does a choke cable work?
A choke valve/cable is designed to restrict the flow of air in the carburettor of an engine. This helps enrich the fuel-air mixture, improving the ability to start an engine in low temperature conditions.
When the choke is on is it open or closed?
Normally choke will be in open position, in which valve is parallel to the air flow, and has no effect on the air flow. When choke is actuated by mechanical or by pneumatic method, it rotates an angle restrict the air flow (closed position).
CHOKE CABLE
Technical help for Series one, two and three Lambrettas. Models include the Li, Li Special, TV, SX, GP, Serveta and API/SIL models
CHOKE CABLE
How do you overcome the problem of the inner choke cable being too long.
