How To Fit Your Glass Splashback
- 1. PEEL off backing: Make sure all corners are well protected from any hard surfaces. Carefully peel off the protective film back. ...
- 2. STICK on the wall: Place the bottom edge of the splashback to the rear of the hob, cooker, range or sink. ...
- 3. SEAL all edges: Use clear silicone sealant to seal around all four sides of the splashback. ...
How do you fix a glass splashback to a wall?
There are two different methods of fixing a glass splashback to a wall: Using adhesive is the easiest route to go down as essentially you just need to apply it to the rear of the splashback and push it into position on the wall and ensure its supported sufficiently until the adhesive cures.
What is a glass Splashback and where can I use it?
The Glass splashback can be placed behind cookers or sinks or (if you feeling adventurous) be used as an alternative to tiling or other finished surfaces between worktops and wall units.
Where do you put a glass splashback behind a hob?
The vast majority of glass splashbacks only cover a section of the wall, directly behind the hob. From an aesthetic perspective, you’re going to want to ensure that the splashback is fitted central to the hob rather than offset to one side. Getting this right is all in the measurements.
How much gap do I need for a glass splashback?
Ensure that the batten is fixed at the correct height allowing for the required 2mm gap. To give you your 2mm gap at the bottom of the splashback and above your worktop surfaces, you will need some 2mm chocks to rest the glass on. These will need to be removed once the adhesive has set.
What is a glass splashback?
Where is the splashback on a kitchen hob?
Is toughened glass stronger than annealed glass?
Can glass be cut?
Can you use clear silicone on glass splashbacks?
What adhesive do you use for glass splashback?
siliconeFor sticking it to the wall, we recommend as a glass splashback adhesive sealant, a neutral clear solvent-free silicone (also known as mirror adhesive or low modular neutral cure silicone – phew!). Its got great bonding strength, quick to cure and is water resistant so just the thing for the job.
Can you stick a glass splashback to tiles?
You can install a simple glass splashback on top of tiles in a matter of minutes using neutral cure silicone, see below for a great example of a glass splashback that has been fitted on top of existing wall tiles. TThis customer chose a glass splashback that compliments the wall tiles and worktops to great effect.
Can a glass splashback be cut to size?
Like splashbacks made of natural stone, glass splashbacks require an additional level of kitchen design planning. That's because the glass needs to be cut to size before it's toughened. Once this is done, the entire piece cannot be cut or processed in any way.
Can you put glass splashback behind cooker?
A glass splashback is a quick and easy way to protect behind your cooker hob, the toughened glass is designed to withstand the heat and day to day use whilst being easy to clean.
Are glass splashbacks a good idea?
Due to their protective nature when it comes to moisture and heat, glass splashbacks are ideal for use in bathrooms too. Glass, naturally, is a fantastic material for splashbacks. The protection offered by a good splashback, can in the long run, save you considerable amounts of money in remedial building costs.
Do glass splashbacks crack?
Glass splashbacks can crack under the pressure of intense heat but this typically only happens when the incorrect glass is used. At CreoGlass we only create splashbacks using toughened glass. Good quality toughened glass is both heat resistant and safe.
How long can a glass splashback be without a join?
A common question that we get asked regarding custom glass splashbacks is; the maximum length that we can go. A large number of our customers want a splashback that is free of glass joins, and rightfully so. The maximum length that we can go in one panel is 3.6 meters.
How thick should a glass splashback be?
6mmA: Splashback thickness is usually 6mm, but we can do other thicknesses e.g. 8mm. Q: Can you see through the splashback glass? A: The glass is back-painted so you cannot see through to the wall or the adhesive. So unlike stained glass, it is a completely opaque finish.
Are glass splashbacks hard to keep clean?
Are glass splashbacks hard to keep clean? One of the biggest benefits of choosing glass is that it offers a seamless, clean design, with no grout lines for mould or grime to grow. This makes it easy to clean with little to no effort, and ensures it will maintain its brand new look for many years.
How do I attach a splashback to the wall?
Apply adhesive While some heavy or out-sized splashbacks require screws for a firm fixing, the most popular way to attach regular glass, metal and other sheet-style splashbacks is by using a combination of double-coated foam tape and low modulus silicone adhesive.
Can you drill holes in glass splashbacks?
A: Absolutely yes! Installing your splashback using both methods of pre-drilled holes or the high strength glue option, are both straight forward for anyone who is confident with DIY.
Do I need splashback behind hob?
Do you need a splashback behind a cooker? Kitchen splashbacks are highly useful as they help protect your walls from scratches, spills, and impacts. The area behind the cooker is prone to high temperatures. Intense heat may damage your wall surface and develop cracks.
Can I glue splashback over tiles?
Can An Acrylic Splashback Be Put Over Tiles? The short answer is Yes.
Can peel and stick backsplash go over tile?
A: Yes, installing peel and stick backsplash over existing tiles is a good idea. This can give your kitchen an updated look without the hassle and mess of traditional tile backsplashes.
Can you put splashback over tiles in bathroom?
An easy and inexpensive way of updating your bathroom is to use acrylic splashbacks in place of standard tiles. You can choose to remove the old tiles first or if the surface is relatively flat, you can place your new splashbacks straight over the top.
Can you glue tiles to glass?
Weldbond Glue - When bonding glass tiles to a glass surface, use Weldbond sparingly if you require a crystal-clear bond. Any whiteness indicates the curing process is not complete.
How to Install a Glass Splashback | Mitre 10 Easy As DIY
A glass splashback is an easy way to improve the look of your kitchen. They come in a variety of colours, and they’ll help protect your walls from messy cook...
What is a glass splashback?
Glass splashbacks are a brilliant way of adding a bold splash of colour to any kitchen. They come with the added benefit of having a highly reflective surface which light can easily bounce off, making a room feel bigger and lighter. Here’s how to install a glass splashback in 5 easy steps. Remember, when working with glass you should always take ...
Where is the splashback on a kitchen hob?
The vast majority of glass splashbacks only cover a section of the wall, directly behind the hob. From an aesthetic perspective, you’re going to want to ensure that the splashback is fitted central to the hob rather than offset to one side. Getting this right is all in the measurements.
Is toughened glass stronger than annealed glass?
Toughened glass is four times stronger than annealed glass but unlike the latter, it cannot be cut once formed. That’s why Glass and Stainless create each glass splashback bespoke to your needs.
Can glass be cut?
Remember, when working with glass you should always take extra care. Don’t leave the glass splashback somewhere where it could be knocked or damaged. At Glass and Stainless we only use toughened glass which is one of the safest forms out there, but it always pays to be careful. Toughened glass is four times stronger than annealed glass but unlike the latter, it cannot be cut once formed. That’s why Glass and Stainless create each glass splashback bespoke to your needs.
Can you use clear silicone on glass splashbacks?
Leave a few millimetres gap from the wall though in order to apply the silicone sealant. When it comes to installing a glass splashback you should only use a clear silicone, not a white one. The transparent nature of glass means that any other type of silicone will simply ruin the look.
How to keep glass splashbacks shiny?
When it comes to cleaning your glass splashback to keep it super shiny and sparkly, follow these simple steps: Try to clean off any splashes as soon as you can. The longer you leave that curry or beans, the harder your job will be. Don’t use anything more abrasive than a soft cloth.
How to install a splashback on a gas stove?
To install the splashback, apply the silicone to the back of the glass in 20mm sized blobs and around 100mm apart. Lift the splashback into position and gently push down to make sure its flat against the wall. Use spacers to keep the splashback from resting directly on the cooker.
How to get streaks off glass?
Use another soft cloth to remove the detergent and dry off the glass. If streaks are left on the surface, take a super soft cloth and give the dry splashback another wipe – circular actions work especially well – and buff to finish.
How to clean splashbacks?
When it comes to cleaning your glass splashback to keep it super shiny and sparkly, follow these simple steps: 1 Try to clean off any splashes as soon as you can. The longer you leave that curry or beans, the harder your job will be. 2 Don’t use anything more abrasive than a soft cloth. Scourers, wash pads, brillo – all a no-no. Our splashbacks have feelings too you know. 3 With your soft cloth in hand, spray or wet the glass with a mild soapy detergent or glass cleaner. 4 Give it a gentle wipe side to side making sure any greasy marks or stains are lifted clean off. Keep going until its all looking tip top once again. 5 Use another soft cloth to remove the detergent and dry off the glass. 6 If streaks are left on the surface, take a super soft cloth and give the dry splashback another wipe – circular actions work especially well – and buff to finish.
How to clean a glass door with a soft cloth?
With your soft cloth in hand, spray or wet the glass with a mild soapy detergent or glass cleaner. Give it a gentle wipe side to side making sure any greasy marks or stains are lifted clean off. Keep going until its all looking tip top once again. Use another soft cloth to remove the detergent and dry off the glass.
How to get 2mm gap on splashback?
These will need to be removed once the adhesive has set. These will be included in with some kits. Apply the adhesive to the rear of the glass in dollops.
Why do you need backlighting for glass splashbacks?
Back lighting for your glass splashback can also be installed to create varying lighting moods or to highlight certain areas or your visual images.
What Type of Glass will I Need to use?
With the use of glass as a splashback, you will need to use toughened glass. This will mean if you are fixing the splashback with screw fixings, the holes for the fixings will have to pre drilled by the glass splashback provider. Any "cut outs" for power sockets, TV points and telephone sockets will need to be made before the glass is toughened as this can’t be done after the toughening process has been completed.
What kind of adhesive do you use for splashbacks?
They should also be able to supply this. In most cases you can also use a suitable construction adhesive such as Gripfill or No Nails or even adhesive pads. One thing you should check is that the adhesive is heat resistant.
How to protect splashback from falling off?
If the splashback has nothing to rest the bottom edge on while the adhesive is drying then you will need to fit a batten to the wall to support its weight until the adhesive is fully set. The batten will need to be screwed to the wall to ensure that it doesn’t come off and risk your splashback coming crashing to the ground. Ensure that the batten is fixed at the correct height allowing for the required 2mm gap.
Why use coloured glass splashbacks?
The use of coloured glass is a great way to improve the style of your kitchen and can create a real feature. The Glass splashback can be placed behind cookers or sinks or (if you feeling adventurous) be used as an alternative to tiling or other finished surfaces between worktops and wall units.
Where should the splashback be on a free standing stove?
If your Cooker or stove is free-standing, you will probably want your splashback to continue below the work surface height at the rear of your cooker / stove to give a clean visual finish to your splash back.
What is a glass splashback?
Glass splashbacks are a brilliant way of adding a bold splash of colour to any kitchen. They come with the added benefit of having a highly reflective surface which light can easily bounce off, making a room feel bigger and lighter. Here’s how to install a glass splashback in 5 easy steps. Remember, when working with glass you should always take ...
Where is the splashback on a kitchen hob?
The vast majority of glass splashbacks only cover a section of the wall, directly behind the hob. From an aesthetic perspective, you’re going to want to ensure that the splashback is fitted central to the hob rather than offset to one side. Getting this right is all in the measurements.
Is toughened glass stronger than annealed glass?
Toughened glass is four times stronger than annealed glass but unlike the latter, it cannot be cut once formed. That’s why Glass and Stainless create each glass splashback bespoke to your needs.
Can glass be cut?
Remember, when working with glass you should always take extra care. Don’t leave the glass splashback somewhere where it could be knocked or damaged. At Glass and Stainless we only use toughened glass which is one of the safest forms out there, but it always pays to be careful. Toughened glass is four times stronger than annealed glass but unlike the latter, it cannot be cut once formed. That’s why Glass and Stainless create each glass splashback bespoke to your needs.
Can you use clear silicone on glass splashbacks?
Leave a few millimetres gap from the wall though in order to apply the silicone sealant. When it comes to installing a glass splashback you should only use a clear silicone, not a white one. The transparent nature of glass means that any other type of silicone will simply ruin the look.
