How To Fit an Inset Kitchen Sink
- Step 1: Remove the old sink (if replacing)
- Step 2: Clean and treat the worktop
- Step 3: Assemble your new kitchen sink
- Step 4: Apply sealing strip/putty
- Step 5: Position the sink
- Step 6: Clamp the clips
- Step 7: Taps & Pipes
How to install a kitchen sink on a kitchen worktop?
The sink should sit perfectly on the sealing putty around the edges that sit on your worktop. With the clips you’ve already attached in step 3, you need these fit the sink’s rim to the worktop. Clamp the sink firmly in place and cut off any excess sealant where possible for a neater appearance.
How do I install a new kitchen sink in my Kitchen?
Carefully place and position your new sink in the gap left by your old model (or in the new gap created in your new kitchen) to ensure a comfortable fit. The sink should sit perfectly on the sealing putty around the edges that sit on your worktop. With the clips you’ve already attached in step 3, you need these fit the sink’s rim to the worktop.
How do you attach a sink to an upside down worktop?
It is very important that the joint between the underside of the sink and the top of the worktop is kept waterproof. This is achieved by sealing putty and most sinks are supplied with this. It either comes in a self-adhesive roll or a small tub. While the sink is upside down, apply the sealing putty to the edges of the sink and fit the sink clips.
How do you cut a kitchen worktop to size?
Cutting the Worktop Slabs Measure the size the worktop will be. Draw the measurements on the worktops. Tape over the measurements for visibility while cutting. Put on goggles and a face mask. Cut the worktop to shape. Find the spots where you’ll put the sink and cooktop. Trace the sink and cooktop on the worktop’s surface.
How do you stick a sink to a countertop?
Use a caulk gun to apply a thick bead of caulk around the edge of the countertop. Raise the sink so it presses against the underside of the countertop and forms a watertight seal. Add boards and shims as needed to ensure the sink stays in place. Use the sink clips to attach the sink to the counter.
How do you attach a sink to a laminate countertop?
3:154:03How to Install a Stock Countertop & Drop-In Sink on a kitchen islandYouTubeStart of suggested clipEnd of suggested clipMany sinks come with a paper template. Place it in your sinks location square it up and tape it downMoreMany sinks come with a paper template. Place it in your sinks location square it up and tape it down. After you trace the shape use a drill with a 3/8 inch bit to drill a hole in each corner.
Where should sink be placed on worktop?
Place your sink upside down on the worktop to enable you to see where to mark out the cutting area. Place the sink where you want it to sit on the base unit, checking that the depth of the sink will drop down unobstructed inside the unit.
Can you install a new sink in existing countertop?
Unless the sink was formed as a continuous component of the countertop, it can be removed and replaced easily – whether it's undermount or drop-in. Though, you will need to make sure that the replacement sink is suited for the same size hole that you already have in the countertop.
How do you install a kitchen sink without clips?
Traditionally, kitchen sinks use mounting hardware to secure the sink to the countertop. However, when you are missing the hardware, or your installer recommends that you avoid drilling the required hardware mounting holes in your granite, you can use silicone adhesive and epoxy to install the sink.
Can you have a drop in sink with laminate countertops?
You may have heard that you can't have an undermount sink with a laminate countertop, but that's old news. Yes, you CAN have an undermount sink!
How far from edge of worktop should sink be?
Final thoughts: the minimum recommended distance between any edge of a wooden worktop and the sink is 50mm, so bear this in mind when dreaming up your layout.
How far from counter edge should sink be?
Draw a line parallel to the front edge of the countertop, indicating how far back the sink should be located. Typically the setback is 2" to 2-1/2" from the front of the counter, depending on the countertop overhang, the type of sink bowl and the size of the sink deck.
What goes first sink or countertop?
After Your New Countertops are Installed You'll likely be getting new sinks along with your new countertops. For best results, it's generally recommended to wait 24 hours after countertop installation before setting up the sink.
How do you install a kitchen sink with a new countertop?
Kitchen Sink Installation in 8 StepsMeasure and Mark the Kitchen Sink's Layout. ... Mark the Cut Lines onto the Counter. ... Cut a Sink Opening with a Jigsaw. ... Install Kitchen Faucet. ... Attach Strainer Over Plumber's Putty. ... Set The Sink and Connect Water Supply. ... Connect the Drain Pipes. ... Attach Dishwasher Drain and Tidy up.
Can a granite countertop be cut to fit a new sink?
Yes, you can cut existing granite for a new sink. However, it's important to recognize the risks of doing so. Usually, you'll need to find a sink with a larger footprint than the old one. Then, you can cut the excess granite away, leaving the right-size cutout for the new sink.
Is it easy to replace a kitchen sink?
Sink replacement is a straightforward project that you can probably tackle yourself. After turning off the water supply, remove the sink by taking apart the pipes, cutting the caulk, and undoing the sink's clamps.
What kind of screws do you use for laminate countertops?
1 1/4-inch long screws should work, though double check before driving them in as you do not want a screw to come through the top.
How do you drill a hole in a laminate countertop?
0:235:36Using a Hole Saw to Cut Laminated Countertop - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou drill with your hole saw from the bottom of the counter. Not don't ever drill into the laminateMoreYou drill with your hole saw from the bottom of the counter. Not don't ever drill into the laminate material itself otherwise you can miss fraying and cracking it.
How do you install a kitchen sink with a new countertop?
Kitchen Sink Installation in 8 StepsMeasure and Mark the Kitchen Sink's Layout. ... Mark the Cut Lines onto the Counter. ... Cut a Sink Opening with a Jigsaw. ... Install Kitchen Faucet. ... Attach Strainer Over Plumber's Putty. ... Set The Sink and Connect Water Supply. ... Connect the Drain Pipes. ... Attach Dishwasher Drain and Tidy up.
What adhesive do you use for countertops?
Epoxy glue is the most common type of glue used in granite installations, as it is one of the few types of adhesives that can provide a bond that is as strong as the stone itself.
How to test if a kitchen sink fits perfectly?
Test to see if the sink fits perfectly in situ and roughly draw around the sink where there may be any obstacles and cut parts of the kitchen base with a jigsaw again if needed.
What Size Lip Do I Need to Fit a Kttchen Sink?
The size of the lip you need to make will depend on your manufacturer's instructions. What I was hesitant was, yes, my instructions said 10mm, yet on Astracast's twitter page, they recommended 12mm.
How to mark 50mm gap?
The way it works is, adjust the triangularish piece to stop at 50mm in my case, then twist to tighten to fix in place.
How big of a gap should I use for a tile backsplash?
I chose to position mine with 50mm gap at the back and 50mm gap at the front. Note, some leave themselves a slightly bigger gap at the back to allow for tiling. I didn't get hung up on this because I knew about 7mm would only be needed later for tiles and adhesive and I'm not going to be picky over that.
What size drill bit do I need to cut curved corners?
This should work for any size bit, but here I'm using a 20mm one.
Do you need to waterproof laminate worktops before fitting?
Then the final stage for now was to remove the masking tape and seal the cut worktop with a waterproof glue or silicone and leave to dry. This is important to prevent water damage if I ever had a plumbing leak or it gets damp.
Can you go back after cutting a hole in a kitchen sink?
Once you cut a hole in your worktop to fit a kitchen sink, there's no going back. That's the only thing that's intimidating about this job, really. Why? Because if you mess it up, you'll probably need to buy a new one which they're not that cheap.
How to test if a kitchen sink fits perfectly?from thecarpentersdaughter.co.uk
Test to see if the sink fits perfectly in situ and roughly draw around the sink where there may be any obstacles and cut parts of the kitchen base with a jigsaw again if needed.
What Size Lip Do I Need to Fit a Kttchen Sink?from thecarpentersdaughter.co.uk
The size of the lip you need to make will depend on your manufacturer's instructions. What I was hesitant was, yes, my instructions said 10mm, yet on Astracast's twitter page, they recommended 12mm.
How to mark 50mm gap?from thecarpentersdaughter.co.uk
The way it works is, adjust the triangularish piece to stop at 50mm in my case, then twist to tighten to fix in place.
How big of a gap should I use for a tile backsplash?from thecarpentersdaughter.co.uk
I chose to position mine with 50mm gap at the back and 50mm gap at the front. Note, some leave themselves a slightly bigger gap at the back to allow for tiling. I didn't get hung up on this because I knew about 7mm would only be needed later for tiles and adhesive and I'm not going to be picky over that.
What size drill bit do I need to cut curved corners?from thecarpentersdaughter.co.uk
This should work for any size bit, but here I'm using a 20mm one.
Do you need to waterproof laminate worktops before fitting?from thecarpentersdaughter.co.uk
Then the final stage for now was to remove the masking tape and seal the cut worktop with a waterproof glue or silicone and leave to dry. This is important to prevent water damage if I ever had a plumbing leak or it gets damp.
Can you go back after cutting a hole in a kitchen sink?from thecarpentersdaughter.co.uk
Once you cut a hole in your worktop to fit a kitchen sink, there's no going back. That's the only thing that's intimidating about this job, really. Why? Because if you mess it up, you'll probably need to buy a new one which they're not that cheap.
How to install multiple worktops?
Place the middle worktop on the support frame. When installing multiple worktop pieces, start with the one that’s furthest back or center. Have a few friends over to hoist the worktops onto the supports. Large worktops are heavy and contact with other surfaces can leave an unsightly scratch.
How to measure for a worktop?
1. Measure the size the worktop will be. Hold a measuring tape up along the wall to determine how much space you have available . If your old worktop is still in place, it can serve as a useful estimate. When building around a corner, plan on connecting 2 slabs or dividing a slab into 2 pieces with a diagonal cut.
How to trace a sink and cooktop?
An easy way to do this is to flip them over and lay them on the worktop’s surface. Masking tape and a marker pen are perfect for creating the guiding lines. Before cutting, move all the lines inward by 5 to 10 mm (0.20 to 0.39 in). This is because the edges of these features hang over the worktop so they don’t fall through.
What is the best material for countertops?
Consider the durability of whichever material you use. Mitchell Newman, the Principal of Habitar Design and Stratagem Construction, says: "Quartz is one of the best substances for countertops because it's very durable. It's also non-porous, which means it's very hard to stain it. It comes in a variety of colors, from a modern clear grey to styles that are veined like marble. Quartzite, or stone quartz, is another great option. It's hard to stain and is relatively uncommon, but it's a little more expensive. You also see granite, marble, and limestone worktops, but those are more porous."
What to put on when sawing worktops?
Put on goggles and a face mask. Before sawing worktop pieces, take safety precautions. Put on goggles to shield your eyes from chipped material. Face masks offer extra protection, so they may be worth the cost.
How much space between wood and wall?
Wood worktops expand and contract a lot. When using them, leave 5 mm (0.20 in) between the wood and the wall. Leave 30 mm (1.2 in) between the wood and a freestanding oven.
How to build around a corner?
When building around a corner, plan on connecting 2 slabs or dividing a slab into 2 pieces with a diagonal cut. For non-square worktops, measure out the space you have available, then carefully measure out how you’ll make your cuts. Wood worktops expand and contract a lot.
How to cut tape off of a worktop?
Drill a 25mm hole in the worktop, inside the taped off area, and push the blade of your jigsaw through the hole. You can drill more than one hole if it makes it easier for you to cut round the inside of the tapes. Keep firm pressure on the jigsaw but do not try to force it to cut faster or you may get a jagged edge.
When fitting a kitchen worktop, do you need to follow the manufacturer's recommendations?
When you are fitting a kitchen worktop you need to follow the manufacturer’s recommendations for cutting and fitting. These vary depending on the material. See more about fitting different kitchen worktops in our Projects section.
Why do you put a sink upside down?
Place your sink upside down on the worktop to enable you to see where to mark out the cutting area.
When is the sink laid on the base unit?
When the worktop is fitted and all the pipes for the plumbing are roughly in place inside the base unit, lay the sink on the worktop.
What tool do you use to cut holes in Formica?
The best tool to use for this is a jigsaw.
Do composite kitchen worktops come preformed?
moulded into the worktop by the manufacturer. As these come preformed, you must be absolutely sure your measurements are correct when you order your worktops.
Do you need to fit a kitchen worktop before you put in a sink?
Many people fit the worktop and sink first then struggle underneath it in a really confined space, but there is no need to fit the kitchen worktop before you get the plumbing ready to accept the sink and taps.
Why do you need to seal the edges of a kitchen sink?
Thisseal is needed to prevent any water leaks and to avoid damage to your worktop.
How to attach new taps to water supply?
Then, apply PTFE tape to the thread of the pipe - where it joins the tap - to create a watertight seal.
How much worktop do I need for a cutout?
You should have about 40-50mm of worktop remaining at the front and back of the cutout. This will be more than enough - the clips need about 20mm to grip. As I said before, often the base unit panels get in the way, but just make slots into the tops of the panels for the clips.
What do darn clips do for a sink?
These can be a right pain to furkle around getting a screwdriver into, and not least that as you apply pressure to tighten the screw the darn clip slips sideways to paint the air a vivid colour of blue.
