HOW TO INSTALL TONGUE & GROOVE PANELING
- Step One Select the species of wood that matches your design. ...
- Step Two Calculate the amount of paneling that you need. ...
- Step Three If it is an existing wall, remove the trim. ...
- Step Four Decide how you are going to finish your paneling. ...
- Step Five Now for the fun part, installing the paneling and watching your wall being transformed. ...
How much cost is installing tongue and groove boards?
Tongue and groove typically costs between $1.25 — $1.60 per linear foot, or around $2.50 to $3.00 per square foot. Some wood species, like cedar, will cost you way more than yellow pine or spruce.
How to install Tongue Groove porch floor board?
How to Install Tongue and Groove Porch Flooring
- Priming. At first, lay the planks facing down across the porch. ...
- Measurement. Measure the first plank such that it is perpendicular across the joists on the porch. ...
- Nailing. Once the planks are cut to appropriate sizes, set all the plank in place, with the grooved side facing the house.
- Layering. ...
- Priming. ...
How to install tongue and groove treated lumber?
How to install a tongue and groove plank wall
- Mark your studs. Use a stud finder or knock or drill holes until you find the studs at the top and bottom of the portion of wall you are going ...
- Avoid visible nail holes. Install planks with the tongue up. ...
- Leave an expansion gap. Don’t install your first row of planks directly on the floor. ...
- Level or parallel. ...
Can you put tongue and groove on to concrete floor?
Unlike hardwood flooring, engineered flooring can be installed over concrete or existing flooring, such as tile or linoleum. Although tongue and groove solid hardwood flooring does fit together, it must still be nailed to a subfloor.
How do you attach tongue and groove paneling?
2:105:28How To Fit Tongue & Groove/Farmhouse Wall PanellingYouTubeStart of suggested clipEnd of suggested clipMarking. Once you're happy pin it to the wall with a nail gun. We recommend pinning the panel on theMoreMarking. Once you're happy pin it to the wall with a nail gun. We recommend pinning the panel on the tongue piece so that your nail hole will be hidden when the next piece is fitted.
Do you glue tongue and groove paneling?
+1 on no glue in the T&G joint. The individual boards need to be able to expand contract individually (That's the advantage of T&G). To solve the exposed unfinished tongue issue, you can pre-stain and finish the tongues before assembly.
How do you fasten tongue and groove?
Drive the nails through the shoulder of the tongues into the framing at about a 45-degree angle. The next grooved edge will hide the nail holes. A 15- or 16-gauge brad nailer with 2-in. nails is the best choice for fastening, although an 18-gauge nailer will do the job, too.
How do you start tongue and groove walls?
Leaving a gap of 1/2″ at each wall surface for expansion and start to install the first row. Install the plank with groove closest to the wall. Secure the first row by nailing into the tongue to the joist, (or furring strip) and secure the groove side of the plank by face nailing into the joist.
Do you nail into the tongue or groove?
The groove of the plank should face the wall and the tongue should face outward. This makes the tongue accessible for nailing, but not the groove.
Should you paint tongue and groove before or after installation?
Paint the tongues. Before installing the tongue-and-groove boards, paint the tongues the same color that you will be painting the finished wainscot. That way no other color will show through when the boards shrink in the winter.
How far apart do you nail tongue-and-groove?
Space the fasteners 12 to 24 inches apart when securing tongue-and-groove boards. Placing the fasteners too close may cause the boards to split.
Which side of tongue-and-groove faces out?
The smooth side should be fitted so it faces outward. Check your planks before you install them. Make sure the rough side is against the wall, ceiling, or floor. This will give a more professional finish.
Can you put tongue-and-groove over drywall?
If you're looking to reboot the atmosphere in a living room or bedroom by covering the existing drywall with tongue-and-groove boards, the good news is that there are no codes prohibiting it. In fact, the fire-resistance of drywall balances the propensity of wood to burn and makes the room safer than wood alone.
Do you need to glue tongue and groove cladding?
T&G panels are uniquely designed so that they can fit together without the need for nails or glue.
Do you need drywall under tongue and groove?
Drywall will help with some types of sound, like people talking or a radio playing, but it won't help much with footfalls and people walking around. If you want to get the most bang for your buck, 5/8" type X drywall and safe and sound mineral wool will help, and stop most normal talking from being heard.
How do you cover a wall with tongue and groove?
Apply a layer of shellac-based primer over the entire wall. Work in long, even strokes, keeping the primer as smooth and even as possible. As you go, roll out any splotches or uneven sections of paint on the surface. Shellac-based stain blocking primer is best for tongue and groove walls.
Do you need to glue tongue and groove cladding?
T&G panels are uniquely designed so that they can fit together without the need for nails or glue.
Should I nail or glue paneling?
You may apply panels with adhesive directly to surfaces that are level, sound and clean. Nail directly into the studs when installing your paneling over existing paneling, wallpapered walls or surfaces which will not support adhesive.
How do you glue tongue and groove?
0:242:21How to float/install a tongue and groove engineered floor ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe'll put it here push it in I have a little tapping block you can make it out of wood this is aMoreWe'll put it here push it in I have a little tapping block you can make it out of wood this is a hard plastic block. I'll just tap it a little bit to make sure the boards are tight.
Can you glue tongue and groove to wall?
Baton is the only way, you do not glue to wall. Then split every tongue/groove every time with secret nailing.
How to contact tongue and groove paneling?
Using these how to install tongue and groove paneling instructions will help ensure your have a successful do-it-yourself project. Call us at 715-369-5700 for tongue and groove ...
How to determine the size of paneling for a wall?
Calculate the amount of paneling that you need. Measure the length and height of each wall, and multiply the height times length to get square footage. Determine the width of plank that you want to install. Pine and cedar normally come in 5″ and 7″ widths, but hardwoods normally can be made in any widths. With these two pieces of information, your supplier should be able to provide the right amount of boards for your job.
How to make a wall longer than planks?
If your wall is longer than your planks, you will have needed to pre-cut the plank to have the end land on the nearest joist. Face nail at the end to the joist. You will need to do the same on the next piece. Measure from the end of your first plank to the end of the wall, leaving the 1/2″for expansion.
Can you nail boards perpendicular to joists?
If you install the boards perpendicular to the joists, you can nail directly to the joists themselves. This is the easiest and quickest method of installation. If you wish to install the boards parallel to the joists, you will have to install furring strips and then secure the paneling to the strips. (On a new wall, blocking between the joists ...
Is tongue and groove wood planks easier to install?
Compared to drywall (which includes steps of installation, taping, mudding and sanding of multiple coats, and 2-3 coats of paint), installation of tongue and groove wood planks is easier, cleaner and much less time consuming. So how easy is it? Let’s walk through the steps of how to install tongue and groove paneling.
Can you paint paneling before installing?
Decide how you are going to finish your paneling. Painting can be done after installation is complete. Finishing with a polyurethane is best done before installation. Since polyurethane is self-leveling, it is best to lay out the individual panels horizontally, (think saw horses), and spray or brush the polyurethane on before installation. Another great idea is to buy your paneling pre-finished and avoid the hassle altogether.
Do you need to nail the groove side of a board?
Since the groove side is now secured by the tongue of the first row, there is now no need to face nail the board on the groove side. Continue to install rows. Check every two-three rows that you are still parallel to the first row or the wall. It may be necessary to cheat on a row by not butting up tight to the previous row.
How to lay tongue and groove paneling?
Continue to lay your boards row by row. Secure a new row of tongue & groove paneling to the row beneath it by sliding the groove (the top side of the row below) into the tongue (the bottom side of the row above)- you may need to use a mallet to get the tongue & groove to secure together. When starting a new row, use your small cut off pieces – this will improve your staggered pattern and prevent creating waste.
What is tongue and groove wall paneling?
Reclaimed tongue & groove wall paneling is a great way to add an interesting wood accent wall to your home. Installing your tongue & groove wall planking can be quick & easy with the right tools and techniques.
Can you replace an outlet cover with paneling?
If you are placing wall paneling around an outlet or light switch, you will need to bump out the outlet as you work. Once your paneling is completely installed, you can replace your outlet cover for a seamless look.
Can you install wood paneling over drywall?
You can install wood paneling directly over drywall- or - in the case of tongue & groove paneling, you can install directly over wall studs since the tongue & groove creates a seal. On your chosen accent wall, use a stud finder to locate your studs, mark each stud with a line so that they are easy to find while you install the wood wall planking.
What is tongue and groove board?
Installing tongue-and-groove (aka T&G) boards is a fast, inexpensive way to panel any ceiling or wall. You can install T&G over bare framing, drywall or plaster, so it's a great cover-up for an ugly ceiling.
Can you cut a board shorter?
Don't fight warped, twisted or bowed boards; cut them shorter. In fact, it's OK to install boards that are only a couple of feet long. They'll look great, and you won't waste any expensive wood.
Can you put tongue and groove together?
(2) You have to seat the tongues and grooves together, and they don't always want to marry. (3) Tongue and groove isn't always flat, so you have to force the boards together to get them seated.
Can you fit grooves in tongue and seat?
Break off the groove flanges. On any installation, you'll have times when you can't fit the groove in the previous tongue and seat the board. In fact, it's almost always the case with the very last board. But it can also happen at shiplap ceiling protrusions or even at projecting inside corners.
Can you run battens parallel to the ceiling?
Also, the battens will somewhat flatten out uneven ceilings. Another plus: You can run the battens either parallel or perpendicular to the ceiling framing, depending on which way you want the tongue and groove to run. Wall and Ceiling Repair Simplified: 11 Clever Tricks.
Can you mark electrical cutouts on tongue and groove?
It's really tricky to accurately mark cutouts for electrical boxes and other ceiling openings on tongue and groove. The secret is to scribe and/or mark as much as possible in place on the shiplap ceiling rather than to try to measure everything perfectly.
Can tongue and groove be painted?
Tongue-and-groove boards are notorious for shrinking and expanding with changes in temperature and humidity. Unfinished tongue and groove boards installed in humid summer conditions can be an ugly mess during the dryness of winter. As the wood dries and shrinks, unfinished stripes will appear where the tongues withdraw from the grooves. But if you apply finish before installation, the tongues will be completely finished—no unfinished stripes to appear later! You could also opt for paint to finish your boards for a white shiplap ceiling look.
What is tongue and groove paneling?
Tongue and groove paneling consists of individual planks that are milled to have a projecting ridge, called a tongue, on one edge and a groove on the opposite edge. When the paneling is installed, the tongue on one panel fits into the groove of the panel next to it.
How to install tongue side panel?
The tongue side will form the long edge of the panel. Install the panel with one end at the bottom corner of the wall, tongue side up, leaving a 1/8-inch gap at the floor. Cut the next panel, using the measurement of the tongue side of the previous panel as the length of the groove side. Continue cutting and installing panels to cover the wall.
How to install diagonal paneling?
Diagonal installation of paneling requires much more cutting and measuring than the other two styles of installation. Begin by nailing up vertical furring strips, then cut a triangular piece of panel by cutting a 45-degree angle at both ends of the piece with the cuts meeting at the grooved edge.
How much space between floor and ceiling?
Leave at least a 1/8-inch space between the panel and the floor and ceiling to allow for expansion of the wood. Continue sliding new panel against the previous panel, tongue into groove, until you reach the next corner, at which point you'll likely need to cut a panel to fit. Advertisement.
Can paneling be installed over existing walls?
Paneling can be installed during construction or, almost as easily, over the top of existing finished walls. Several techniques for installing paneling are common, each with its own distinct aesthetic character. Advertisement.
